E13 石油钻井 标准查询与下载

SY/T 6709-2008 膏盐层钻井技术规程

本标准规定了膏盐层钻井工艺要求、钻井施工重点措施和钻井复杂情况处理方法。 本标准适用于油气井膏盐层钻井作业。

Drilling technology rules for gypsolith and salt formation

SY/T 6708-2008 石油天然气钻井液日报表

本标准规定了石油天然气工业钻井工程过程中钻井液用日报表的格式。 本标准适用于石油天然气工业钻井工程中钻井液工作领域。

Daily drilling fluid report for oil and natural gas industry

SY/T 6707-2008 海洋井场调查规范

本标准规定了1500m水深以内的移动式海上钻井装置井场调查的内容、方法和技术要求。 本标准适用于移动式海上钻井装置井场的工程地质和工程物探调查。

Specification for marine well site survey

ISO 10414-1:2008 石油和天然气工业.钻井液的现场测试.第1部分:水基液

This part of ISO 10414 provides standard procedures for determining the following characteristics of water-based drilling fluids: a) drilling fluid density (mud weight); b) viscosity and gel strength; c) filtration; d) water, oil and solids contents; e) sand content; f) methylene blue capacity; g) pH; h) alkalinity and lime content; i) chloride content; j) total hardness as calcium. Annexes A through K provide additional test methods which may be used for -- chemical analysis for calcium, magnesium, calcium sulfate, sulfide, carbonate and potassium; -- determination of shear strength; -- determination of resistivity; -- removal of air; -- drill-pipe corrosion monitoring; -- sampling, inspection and rejection; -- rig-site sampling; -- calibration and verification of glassware, thermometers, viscometers, retort-kit cup and drilling-fluid balances; -- permeability-plugging testing at high temperature and high pressure for two types of equipment; -- example of a report form for water-based drilling fluid.

Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids

ASTM D7400-08 井下地震测试的标准试验方法

The seismic downhole method provides a designer with information pertinent to the seismic wave velocities of the materials in question (1). The P-wave and S-wave velocities are directly related to the important geotechnical elastic constants of Poisson’s ratio, shear modulus, bulk modulus, and Young’s modulus. Accurate in-situ P-wave and S-wave velocity profiles are essential in geotechnical foundation designs. These parameters are used in both analyses of soil behavior under both static and dynamic loads where the elastic constants are input variables into the models defining the different states of deformations such as elastic, elasto-plastic, and failure. Another important use of estimated shear wave velocities in geotechnical design is in the liquefaction assessment of soils. A fundamental assumption inherent in the test methods is that a laterally homogeneous medium is being characterized. In a laterally homogeneous medium the source wave train trajectories adhere to Snell’s law of refraction. Another assumption inherent in the test methods is that the stratigraphic medium to be characterized can have transverse isotropy. Transverse isotropy is a particularly simple form of anisotropy because velocities only vary with vertical incidence angle and not with azimuth. By placing and actuating the seismic source at offsets rotated 90° in plan view, it may be possible to evaluate the transverse anisotropy of the medium. Note 18212;The quality of the results produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D 3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D 3740 provides a means of evaluating some of those factors.1.1 These test methods are limited to the determination of the interval velocities from arrival times and relative arrival times of compression (P) and vertically (SV) and horizontally (SH) polarized shear (S) seismic waves which are generated near surface and travel down to an array of vertically installed seismic sensors. A preferred method intended to obtain data for use on critical projects where the highest quality data is required is included. Also included is an optional method intended for use on projects which do not require measurements of a high degree of precision. 1.2 Various applications of the data will be addressed and acceptable procedures and equipment, such as seismic sources, receivers, and recording systems will be discussed. Other items addressed include source-to-receiver spacing, drilling, casing, grouting, a procedure for borehole installation, and conducting actual borehole and seismic cone tests. Data reduction and interpretation is limited to the identification of various seismic wave types, apparent velocity relation to true velocity, example computations, use of Snell''s law of refraction, and assumptions. 1.3 There are several acceptable devices that can be used to generate a high-quality P or SV source wave or both and SH source waves. Several types of commercially available receivers and recording systems can also be used to conduct an acceptable downhole survey. Special consideration should be given to the types of receivers used and their configuration. Heavily-damped sensors should not be used so that spectr......

Standard Test Methods for Downhole Seismic Testing

GOST R 53240-2008 油气探井.试验规则

Oil and gas exploratory wells. Rules of testing

SY/T 5480-2007 固井设计规范

本标准规定了石油及天然气钻井固井设计的技术要求。 本标准适用于石油及天然气钻井固井设计，其他行业固井设计也可参考执行。

Specification for cementing design

SY/T 5089.1-2007 钻井井史格式 第1部分：陆地部分

SY/T 5089-2007的本部分规定了石油及天然气陆上钻井井史的格式、内容和填写要求。 本部分适用于石油天然气陆上钻井井史。

Well history format for drilling Part 1: Onshore drilling

SY/T 5089.2-2007 钻井井史格式 第2部分：海上部分

SY/T 5089-2007 的本部分规定了钻井井史的格式、内容和填写技术要求。 本部分适用于海上勘探、开发各类井的钻井井史编写。

Well history format for drilling Part 2: Offshore drilling

SY/T 5172-2007 直井井眼轨迹控制技术规范

本标准规定了石油与天然气钻井直井井眼轨迹控制技术指标，设计技术要求，工具、测量仪器的配备和使用要求。 本标准适用于直井的井眼轨迹控制。

Specifications for trajectory control in straight holes

SY/T 5467-2007 套管柱试压规范

本标准规定了油气井套管柱的试压时间、方法、指标及组织与实施。 本标准适用于石油与天然气井各层次套管固井施工作业后的套管柱试压。

Specification for casing string pressure test

SY/T 5840-2007 钻井液用桥接堵漏材料室内试验方法

本标准规定了钻井液用桥接堵漏材料的室内试验方法。 本标准适用于钻井液用桥接堵漏材料室内试验。

Recommended practice for laboratory testing of bridging materials for drilling fluids

SY/T 6704-2007 井斜仪校准装置校准方法

本标准规定了井斜仪校准装置的计量特性、校准条件、校准项目、校准方法、校准结果和校准间隔。 本标准适用于新建立、使用中和修理后的三轴转台井斜仪校准装置的校准，其他类型的井斜仪校准装置亦可参照使用。

Calibration method of inclinometer calibration facility

BS EN ISO 13503-2:2006+A1:2009 石油和天然气工业.完井液和材料.水力压裂和砾石填充作业用支撑剂性能测定

This part of ISO 13503 provides standard testing procedures for evaluating proppants used in hydraulic fracturing and gravel-packing operations. NOTE “Proppants” mentioned henceforth in this part of ISO 13503 refer to sand, ceramic media, resin-coated proppants, gravel-packing media and other materials used for hydraulic fracturing and gravel-packing operations. The objective of this part of ISO 13503 is to provide a consistent methodology and specifications for testing performed on hydraulic fracturing and/or gravel-packing proppants.

Petroleum and natural gas industries - Completion fluids and materials - Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations

SY/T 5313-2006 钻井工程术语

本标准规定了石油钻井工程专用的术语。 本标准适用于石油钻井工程领域，也适用于石油工业的其他领域。

Vocabulary of well drilling engineering

BS EN 15112:2006 油井套筒防外部腐蚀用阴极保护

This European Standard specifies methods used to evaluate the external corrosion hazards of well casings, as well as cathodic protection means and devices to be implemented in order to prevent corrosion of the external part of these wells in contact with the soil. This European Standard applies to any gas, oil or water well with metallic casing, whether cemented or not. However, in special conditions (shallow casing: e.g. 50 m, and homogeneous soil), EN 12954 can be used to achieve the cathodic protection and assess its efficiency. This European Standard also describes techniques allowing determination of the current required for protection and ensuring correct operation of the cathodic protection devices installed.

External cathodic protection of well casing

SY/T 5374.1-2006 固井作业规程 第1部分:常规固井

SY/T 5374的本部分规定了常规固井作业要求和作业程序。 本部分适用于石油及天然气钻井中常规固井作业施工。

Cementing specification. Part 1: Conventional primary well cementing

SY/T 5964-2006 钻井井控装置 组合配套安装调试与维护

本标准规定了钻井井控装置组合配套型式、安装、调试与维护要求。 本标准适用于陆上石油天然气钻井井控装置。

Combination installation adjustment and maintenance of well-control equipments

SY/T 5416.1-2006 定向井测量仪器测量及检验 第1部分:无线随钻类

SY/T 5416的本部分规定了脉冲类无线随钻测量仪器的测量工作条件、测量准备、测量、回收与保养、检验通则、地面操作系统的检查、井下系统的检验及检验结果的处理。 本部分适用于定向井脉冲类无线随钻测量仪器的测量及检验。

Measurement and inspect regulation of directional surveying instruments. Part 1: Measurement while drilling

SY/T 5374.2-2006 固井作业规程 第2部分:特殊固井

SY/T 5374的本部分规定了内管法注水泥、双级注水泥、尾管注水泥、挤水泥和注水泥塞等特殊工艺固井的要求和作业程序。 本部分适用于石油及天然气钻井中的特殊固井作业。

Cementing specification. Part 2: Special cementing