E42 石油蜡 标准查询与下载

NB/SH/T 0408-2013 蜡纸或纸板表面蜡量测定法

本标准规定了蜡纸或纸板表面蜡量测定方法。

Standard test method for surface wax on waxed paper or paperboard

NB/SH/T 0399-2013 石油蜡过氧化值测定法

本标准规定了石油蜡过氧化值的测定方法。本标准适用于石油蜡类产品。

Standard test method for peroxide number of petroleum wax

NB/SH/T 0417-2013 轻质液体石蜡

本标准规定了轻质液体石蜡的要求和试验方法、检验规则、标志、包装、运输、贮存和安全。本标准适用于用作化工原料的轻质液体石蜡。

Light liquid paraffin wax

NB/SH/T 0588-2013 石油蜡体积收缩率测定法

本标准规定了石油蜡体积收缩率的测定方法。本标准适用于石蜡和微晶蜡,也适用于天然蜡、合成蜡及特种蜡产品。

Standard test method for determining the volume contraction of petroleum waxes

NB/SH/T 0407-2013 石油蜡水溶性酸或碱试验法

本标准规定了石油蜡水溶性酸或碱试验方法。本标准适用于石蜡和微晶蜡。

Standard test method for water soluble acids and alkalis of petroleum waxes

NB/SH/T 0871-2013 橡胶防护蜡

本标准规定了橡胶防护蜡的产品分类、技术要求和试验方法、取样、检验规则、标志、包装、运输和贮存。本标准适用于以石蜡、微晶蜡为主要原料,通过添加其他助剂得到的橡胶防护蜡。本标准所属产品主要用于各种橡胶制品的物理防老。

Protective wax for rubber

NB/SH/T 0875-2013 家禽拔毛专用蜡

本标准规定了家禽拔毛专用蜡的产品分类、技术要求和试验方法、取样、标志、包装、运输和贮存。本标准适用于以食品级石油蜡为基础组份,添加一定量的食品级改性添加剂,经物理调和而制得的家禽拔毛专用蜡。

Poultry defeathering wax

DIN 51532:2012 石油蜡.熔点的测定(冷却曲线)

Petroleum waxes - Determination of melting point (cooling curve)

DIN 51531:2012 石油蜡.含油量的测定

Petroleum waxes - Determination of oil content

QB/T 4362-2012 蜡制品.蜡烛用石蜡

本标准规定了蜡烛用石蜡的技术要求、试验方法、检验规则和标志、包装、运输、贮存及保质期。 本标准适用于以含油蜡为原料，经发汗或溶剂脱油，再经白土或加氢精制所得到的蜡烛用石蜡。

Wax product.Paraffin wax for candle

ASTM D3944-12 石蜡凝固点的标准试验方法

5.1 The related methods of determining the melt point of petroleum wax are relatively time-consuming. This method endeavors to reduce the duration of testing significantly and at the same time maintain a reasonable precision. This method can be useful for quality control of petroleum waxes as well as research and product development work on these waxes. 5.2 For methods used for testing melt points of petroleum waxes, see Tests Method D87, D127, including Petrolatum and Test Method D938. 1.1 This test method covers a procedure for rapidly determining the solidification point of petroleum wax. Note 1—This test method is also applicable to similar materials such as synthetic waxes but the precision may vary. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Solidification Point of Petroleum Wax

ASTM D3944-12(2017) 石油蜡凝固点的标准试验方法

5.1 The related methods of determining the melt point of petroleum wax are relatively time-consuming. This method endeavors to reduce the duration of testing significantly and at the same time maintain a reasonable precision. This method can be useful for quality control of petroleum waxes as well as research and product development work on these waxes. 5.2 For methods used for testing melt points of petroleum waxes, see Tests Method D87, D127, including Petrolatum and Test Method D938. 1.1 This test method covers a procedure for rapidly determining the solidification point of petroleum wax. Note 1: This test method is also applicable to similar materials such as synthetic waxes but the precision may vary. 1.2 The values stated in SI units are to be regarded as the standard. . 1.2.1 Exception—The values given in parentheses are for information only 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Solidification Point of Petroleum Wax

ASTM D938-12(2017) 包括凡士林在内的石油蜡冷凝点的标准试验方法

5.1 Congealing point is a wax property that is of interest to many petroleum wax consumers. The procedure described here measures the temperature at which a sample being cooled develops a “set” or resistance to flow. At that temperature, the wax may be at or close to the solid state, or it may be semisolid and quite unctuous, depending on the composition of the wax or petrolatum being tested. In the case of petrolatums, congealing property is associated with the formation of a gel structure as the sample cools. 1.1 This test method covers determination of the congealing point of petroleum waxes, including petrolatum. 1.2 The values stated in SI units are to be regarded as the standard. 1.2.1 Exception—The values given in parentheses are for information only. 1.3 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: This test method is an alternative to Test Method D127. Results obtained are usually lower than the results obtained by Test Method D1278201;–8201;IP8201;133, the amount of the deviation varying with the nature of the petroleum wax. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Congealing Point of Petroleum Waxes, Including Petrolatum

ASTM D938-12 包括凡士林在内的石油蜡凝固点的标准试验方法

5.1 Congealing point is a wax property that is of interest to many petroleum wax consumers. The procedure described here measures the temperature at which a sample being cooled develops a “set” or resistance to flow. At that temperature, the wax may be at or close to the solid state, or it may be semisolid and quite unctuous, depending on the composition of the wax or petrolatum being tested. In the case of petrolatums, congealing property is associated with the formation of a gel structure as the sample cools. 1.1 This test method covers determination of the congealing point of petroleum waxes, including petrolatum. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1—This test method is an alternative to Test Method D127. Results obtained are usually lower than the results obtained by Test Method D1278201;–8201;IP8201;133, the amount of the deviation varying with the nature of the petroleum wax.

Standard Test Method for Congealing Point of Petroleum Waxes, Including Petrolatum

NB/SH/T 0556-2010 石油蜡溶剂抽出物测定法

本标准规定了石油蜡溶剂抽出物的测定方法。 本标准采用国际单位制[SI]单位。 本标准可能涉及某些有危险的材料、设备和操作，但是无意对此有关的所有安全问题都提出建议。因此，在使用之前，用户有责任建立适当的安全和防护措施，并确定相关规章的适用性。

Standard test method for solvent extractables in petroleum waxes

NB/SH/T 0401-2010 石油蜡粘点和结点测定法

1.1本标准规定了石油蜡粘点和结点的测定方法。本标准适用于石油蜡。 1.2本标准可能涉及某些有危险的材料、设备和操作，但并无意对与此有关的所有安全问题都提出建议。因此，在使用本标准之前，用户有责任建立适当的安全和防护措施，并确定相关规章的适用性。

Standard test method for blocking and picking points of petroleum wax

NB/SH/T 0848-2010 聚乙烯蜡表观黏度测定法

本标准规定了用布氏LVT或LVF型黏度计和加热系统测定聚乙烯蜡表现黏度的方法。 本标准可能涉及某些有危险的材料、设备和操作，但并无意对与此相关的所有安全问题都提出建议。因此，在使用本标准之前，用户有责任建立适当的安全和防护措施，并确定相关规章的适用性。

Standard test method for determining the apparent viscosity of polyethylene wax

NB/SH/T 0809-2010 天然蜡和合成蜡酸值测定法

1．1本标准规定了天然蜡和合成蜡酸值测定方法。 1．2本标准用乙醇-二甲苯混合物作溶剂，适用于所有的天然蜡，包括巴西棕榈蜡。也适用于氧化的微晶蜡、氧化的费一托合成蜡、氧化聚乙烯蜡和褐煤蜡。 1．3本标准可能涉及某些有危险的材料、设备和操作，但并无意对与此有关的所有安全问题都提出建议。因此，在使用本标准之前，使用者有责任建立适当的安全和防护措施，并制定有适用性的管理制度。

Standard test method for acid number (empirical) of synthetic and natural waxes

DIN 51579:2010 石腊检验. 针入法测定

This document specifies the determination of the density at room temperature or higher testing temperature of solid to semisolid mineral oil paraffins, microcrystalline wax, petroleum jelly, synthetic paraffins and waxes. This test method is applicable by a needle penetration of up to 250 scale divisions (1 scale division is equivalent to 0,1 mm).

Testing of paraffin - Determination of needle penetration

ASTM D1321-10 石油蜡针入度的标准试验方法

Petroleum waxes differ in hardness. Needle penetration is a measurement of hardness. Hardness may have a significant effect upon other physical properties.1.1 This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle. This test method is applicable to waxes having a penetration of not greater than 250. Note 18212;This test method is similar to the needle method for determining the penetration of bituminous material, Test Method D5. Cone methods applicable to greases and to petrolatum are described in Test Methods D217 and Test Method D937, respectively. 1.2 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Needle Penetration of Petroleum Waxes