E42 石油蜡 标准查询与下载

ASTM D1465-10 石油蜡的粘结点和粘着点的标准试验方法

Blocking of waxed paper, because of the relatively low temperatures at which it may occur, can be a major problem to the paper-coating industry. For example, when the waxed surfaces in a roll of waxed paper stick together, upon separation the surface films are marred and the glossy finish is destroyed. The wax picking point and the wax blocking point indicate an approximate temperature range at or above which waxed surfaces in contact with each other are likely to cause surface film injury.1.1 This test method covers the determination of the blocking point and picking point of petroleum wax. 1.2 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Blocking and Picking Points of Petroleum Wax

ASTM D1386-10 合成和天然蜡的酸值(经验法)的标准试验方法

This test method is used to determine the property of acid functionality. Acid functionality determines the utility of the wax as well as being a significant Quality Control test. 1.1 This test method covers the determination of the acid number of synthetic waxes and natural waxes. The number is obtained by direct titration of the material and indicates the amount of free acid present. 1.2 This test method, using an ethanol-xylene mixture, is applicable to all natural waxes, including carnauba. The test method is also applicable to oxidized microcrystalline waxes, oxidized Fischer-Tropsch, oxidized polyethylene, and montan esters. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acid Number (Empirical) of Synthetic and Natural Waxes

SANS 1265:2009 合成工艺和其它石油资源中得到的蜡油

Covers two types of waxy oil, for use in the blending of creosote/oil wood preservative mixtures.

Waxy oil obtained from the synthol process and from other petroleum sources

JIS K 2236 AMD 1:2009 汽车抛光蜡(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS K 2236:1997 is partially replaced with this Amend- ment.

Polish for automobiles (Amendment 1)

JIS K 2235 AMD 1:2009 石蜡(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS K 2235:1991 is partially replaced with this Amend- ment.

Petroleum waxes (Amendment 1)

ASTM D87-09 石油蜡熔点的标准试验方法(冷却曲线)

Melting point (cooling curve) is a test that is widely used by wax suppliers and consumers. it is particularly applied to petroleum waxes that are rather highly paraffinic or crystalline in nature. A plateau occurs with specimens containing appreciable amounts of hydrocarbons that crystallize at the same temperature, giving up heat of fusion, thus temporarily retarding the cooling rate. In general, petroleum waxes with large amounts of non-normal hydrocarbons or with amorphous solid forms will not exhibit a plateau.1.1 This test method covers the determination of the melting point (cooling curve) of petroleum wax. It is unsuitable for waxes of the petrolatum group, microcrystalline waxes, or blends of such waxes with paraffin wax or scale wax. Note 18212;For additional methods used for testing petroleum waxes, see Test Method D127 and Test Method D938. Results may differ, depending on the method used. For pharmaceutical petrolatum, Test Method D127 usually is used. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Melting Point of Petroleum Wax (Cooling Curve)

SANS 13:2008 地板和家具用基于溶剂的上光蜡

Covers two forms, i.e. liquid and paste, of solvent-based wax polish suitable for use on furniture and floors, other than those of thermoplastic (asphalt), semi flexible vinyl (vinyl-asbestos), flexible vinyl, linoleum, and rubber.

Wax polish, solvent-based, for floors and furniture

SANS 15:2008 地板和家具用乳化上光蜡

Covers wax emulsion paste polish and two types of wax emulsion liquid polish suitable for use on furniture and floors other than (in the case of polish containing an organic solvent) those of thermoplastics (asphalt), semi-flexible vinyl (vinyl-asbestos)

Wax emulsion polish for floors and furniture

DIN 51580:2008 石蜡试验.针入度的测定

Testing of petroleum waxes - Determination of cone penetration

SH/T 0013-2008 微晶蜡

1.1本标准规定了微晶蜡的技术要求、试验方法、标志、包装、贮运、取样。 1.2本标准适用于由石油的重馏分或减压渣油的溶剂脱沥青油经过溶剂精制、脱蜡、脱油、再经白土或加氢精制得到的微晶蜡。 1.3本标准所属产品适用于军工、电子、冶金和化工等行业的用蜡。主要用于防潮、防腐、粘结、上光、绝缘、钝感、铸膜和橡胶防护等。

Microcrystalline wax

SH/T 0404-2008 石蜡光安定性测定法

1.1本标准规定了石蜡光安定性测定方法，适用于食品用石蜡、全精炼石蜡和半精炼石蜡。 1.2本标准可能涉及某些有危险的材料、设备和操作，但并无意对与此有关的所有安全问题都提出建议。因此，在使用本标准之前，用户有责任建立适当的安全和防护措施，并制定有适当性的管理制度。

Test method for light stability of paraffin wax

SH/T 0807-2008 炸药专用复合蜡

本标准规定了以不同馏程的含蜡馏分或与助乳剂、增稠剂等复合而制得的炸药专用复合蜡的要求、试验方法、取样、标志、包装、运输和贮存。 本标准所属产品适用于民用爆破等行业。

Special compound wax for dynamite

ASTM D127-08 包括凡士林在内的石油蜡滴熔点的标准试验方法

Melting point is a wax property that is of interest to most wax consumers. It can be an indication of the performance properties of the wax. Drop melting point, Test Method D 127, is often used to measure the melting characteristics of petrolatums and other high viscosity petroleum waxes.1.1 This test method covers the determination of the drop melting point of petroleum wax. It is used primarily for petrolatums and other microcrystalline wax. Note 18212;Additional methods used for petroleum waxes are Test Method D 87 and Test Method D 938. Results obtained may differ, depending on the method used. For pharmaceutical petrolatum, Test Method D 127 usually is used. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Drop Melting Point of Petroleum Wax, Including Petrolatum

SH/T 0800-2007 蜡滴点测定法

1.1 本标准规定了测定蜡滴点的试验方法，适用于包括石蜡、微晶蜡、聚乙烯蜡、调合蜡和天然蜡在内所有类型的非液态蜡。 1.2 本标准可能涉及某些有危险的材料、设备和操作，但并无意对此有关的所有安全问题都提出建议。因此，在使用本标准之前，用户有责任建立适当的安全和防护措施，并制定有适用性的管理制度。

Standard test method for dropping point of waxes

SH/T 0398-2007 石油蜡和石油脂分子量测定法

1.1 本标准规定了用蒸气压渗透法（简称 VPO 法）测定石油蜡和石油脂分子量的方法。 1.2 本标准适用于石蜡、微晶蜡、液体石蜡、白色油、凡士林及能被邻二氯苯、甲苯溶剂溶解的特种蜡，不适用于容易缔合或解离的物质。 1.3 本标准包含标准曲线法和仪器常数法，其中标准曲线法只适用于分子量＜800 的样品，仪器常数法适用于全部测量范围。 1.4 本标准未对与使用有关的所有安全问题都提出建议，因此，在使用本标准之前，使用者应建立适当的安全和防护措施，并制定相应的管理制度。

Standard test method for molecular weight of petrolemn wax and petrolatum

SH/T 0018-2007 含添加剂石油蜡(热熔胶)表观粘度测定法

1.1 本标准规定了含添加剂石油蜡（热熔胶）表观粘度的测定方法，适用于温度低于 175℃时表观粘度低于20Pa·S 的液态热熔物。 1.2 本标准规定以国际单位制作为标准计量单位。 1.3 本标准可能涉及某些有危险的材料、设备和操作，但并无意对与此有关的所有安全问题都提出建议。因此，在使用本标准之前，用户有责任建立适当的安全和防护措施 ，并制定有适用性的管理制度。

Standard test method for apparent viscosity of petroleum waxes compounded with additives (hot melts)

ASTM D87-07 石蜡熔点的标准试验方法(冷却曲线)

Melting point (cooling curve) is a test that is widely used by wax suppliers and consumers. it is particularly applied to petroleum waxes that are rather highly paraffinic or crystalline in nature. A plateau occurs with specimens containing appreciable amounts of hydrocarbons that crystallize at the same temperature, giving up heat of fusion, thus temporarily retarding the cooling rate. In general, petroleum waxes with large amounts of non-normal hydrocarbons or with amorphous solid forms will not show the plateau.1.1 This test method covers the determination of the melting point (cooling curve) of petroleum wax. It is unsuitable for waxes of the petrolatum group, microcrystalline waxes, or blends of such waxes with paraffin wax or scale wax. Note 1For additional methods used for testing petroleum waxes, see Test Method D 127 and Test Method D 938. Results may differ, depending on the method used. For pharmaceutical petrolatum, Test Method D 127 usually is used.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Melting Point of Petroleum Wax (Cooling Curve)

ASTM D87-07a 石蜡熔点的标准试验方法(冷却曲线)

1.1 This test method covers the determination of the melting point (cooling curve) of petroleum wax. It is unsuitable for waxes of the petrolatum group, microcrystalline waxes, or blends of such waxes with paraffin wax or scale wax. Note 1For additional methods used for testing petroleum waxes, see Test Method D 127 and Test Method D 938. Results may differ, depending on the method used. For pharmaceutical petrolatum, Test Method D 127 usually is used.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Melting Point of Petroleum Wax (Cooling Curve)

ASTM D937-07(2012) 矿脂针入度的标准试验方法

1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Cone Penetration of Petrolatum

ASTM D2669-06(2012)e1 混有添加剂的石油蜡(热熔体)表观粘度的标准试验方法

This test distinguishes between hot melts having different apparent viscosities. It is believed that apparent viscosity determined by this procedure is related to flow performance in application machinery operating under conditions of low shear rate. Apparent viscosity as determined by this method may not correlate well with end use applications where high shear rates are encountered. Materials of the type described in this procedure may be quite non-Newtonian and as such the apparent viscosity will be a function of shear rate under the conditions of test. Although the viscometer described in this test generally operates under conditions of relatively low shear rate, differences in shear effect can exist depending upon the spindle and rotational speed conditions selected for the test program. Maximum correlation between laboratories, therefore, depends upon testing under conditions of equivalent shear.1.1 This test method covers the determination of the apparent viscosity of petroleum waxes compounded with additives (hot melts). It applies to fluid hot melts having apparent viscosities up to about 20 Pa·s at temperatures up to 175°C (347°F). Note 18212;For petroleum waxes and their blends having low apparent viscosities, below about 15 mPa·s, Test Method D445, is especially applicable. 1.2 The values stated in SI units shall be regarded as the standard. One pascal second (Pa·s) = 1000 centipoises (cP). One millipascal second (mPa·s) = 1 centipoise (cgs units). 1.3 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Apparent Viscosity of Petroleum Waxes Compounded with Additives (Hot Melts)