H53 电工用钢 标准查询与下载

YB/T 4517-2016 700MW及以上级大型电机用冷轧无取向电工钢带

Cold-rolled non-oriented electrical steel strip for large motors of 700MW and above

ASTM A677-16 无取向电气钢完全处理类型的标准规格

1.1 This specification covers the detailed requirements to which flat-rolled nonoriented fully processed electrical steel shall conform. 1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50 and 60 Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed during mill processing, so additional heat treatment by the user is usually not necessary. 1.3 These nonoriented fully processed electrical steels are low-carbon, silicon-iron, or silicon-aluminum-iron alloys containing up to about 3.58201;% silicon and a small amount of aluminum. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel Fully Processed Types

ASTM A683-16 无取向电气钢半处理类型的标准规格

1.1 This specification covers the detailed requirements to which flat-rolled, nonoriented semiprocessed electrical steel shall conform. 1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50 and 60 Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed through heat treatment by the user. 1.3 These nonoriented, semiprocessed electrical steels are low carbon, silicon-iron or silicon-aluminum-iron alloys containing up to about 2.58201;% silicon and less than 18201;% aluminum. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types

DIN EN 10251:2015 磁性材料.测定电工钢片和电工钢带几何特性值的方法;德文版本EN 10251-2015

Magnetic materials - Methods of determination of the geometrical characteristics of electrical steel sheet and strip; German version EN 10251:2015

BS EN 10106:2015 冷轧无取向电工钢带材和板材以完全加工状态交货

Cold rolled non-oriented electrical steel strip and sheet delivered in the fully processed state

BS EN 10303:2015 中频用薄磁钢带材和薄板

Thin magnetic steel strip and sheet for use at medium frequencies

BS EN 10330:2015 磁性材料.磁性开路中磁性材料矫顽力的测量方法

Magnetic materials. Method of measurement of the coercivity of magnetic materials in an open magnetic circuit

BS EN 10251:2015 磁性材料 电工钢板及钢带几何特性的测定方法

Magnetic materials. Methods of determination of the geometrical characteristics of electrical steel sheet and strip

IEC 60404-8-1:2015 磁性材料.第8-1部分:单项材料规范.硬磁材料

Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials

ASTM A664-15 识别ASTM规范中标准电工钢级别的标准实践规程

1.1 This practice covers the procedure for designating (within ASTM specifications) standard grades of flat-rolled electrical steels made to specified maximum values of specific core loss. This practice applies to magnetically soft irons and steel (low-carbon steels and alloys of iron with silicon, aluminum, and other alloying elements) where a core loss measurement at a stated peak value of alternating induction and a stated frequency, such as 1.5 T (15 kG) and 60 Hz, is normally used to grade the material. This practice also applies when some other property is specified (or a different induction or frequency, or both) as the limiting characteristic, provided the material also meets all the requirements of the ASTM specification. 1.2 Individual specifications that are in conformity with this practice are Specifications A677, A683, A726, A876, and A1086. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications

YB/T 5224-2014 中频用电工钢薄带

本标准规定了频率为100Hz~10kHz磁路结构中使用的冷轧取向和无取向电工钢薄带的术语和定义、分类、牌号、一般要求、技术要求、几何特性和偏差、检查和测试、检验、包装、标志和质量证明书等。本标准适用于公称厚度为0. 05mm~0. 20mm并以退火状态和卷状供货的电工钢薄带。

Specification for thin electrical steel strip for use at medium frequencies

DIN EN 10107:2014 以完全加工状态交付的晶粒定向电工钢片和钢带

Grain-oriented electrical steel strip and sheet delivered in the fully processed state; German version EN 10107:2014

BS EN 10107:2014 以完全加工状态交付的晶粒定向电工钢带和钢板

Grain-oriented electrical steel strip and sheet delivered in the fully processed state

JIS C 2552:2014 全加工状态中运送的冷轧不定向电工钢带和薄板

This Standard defines the grades of cold-rolled non-oriented electrical steel strip and sheet with insulation on both sides in nominal thicknesses of 0.35 mm, 0.47 mm,0.50 mm,0.65 mm and 1.00 mm (hereafter referred to as "steel strip"). In particular,it gives general requirements, magnetic properties,geometric characteristics,tolerances,technological characteristics,as well as inspection procedures.

Cold-rolled non-oriented electrical steel strip and sheet delivered in the fully-processed state

SN/T 3468.7-2013 钢材残损检验鉴定规程 第7部分：电工钢板和钢带

SN/T 3468的本部分规定了残损电工钢板和钢带检验鉴定的一般程序和要求。本部分适用于电工钢板和钢带残损的检验鉴定。

Rules for the damage survey of steel materials.Part 7:Electrical steel sheets and strips

SN/T 3514-2013 电工钢晶粒取向与无取向鉴定方法 X射线衍射测定织构法

本标准规定了X射线衍射测定织构鉴定电工钢晶粒取向与无取向的方法。本标准适用于晶粒取向与无取向电工钢的鉴定。

Identification method of texture analysis for grain oriented and non-oriented electrical steels.X-ray diffraction(XRD)

ASTM A1086-13 全加工型平轧晶粒取向硅铁电工钢标准规格

1.1 This specification covers the detailed requirements to which flat-rolled thin-gauge nonoriented fully processed electrical steel shall conform. Nominal thicknesses included in this specification are 0.004 in. (0.10 mm) to 0.012 in. (0.30 mm). 1.1.1 Refer to Specification A677 for properties of flat-rolled nonoriented fully processed electrical steel in nominal thicknesses of 0.014 in. (0.36 mm) to 0.025 in. (0.64 mm). 1.1.2 Refer to Specification A876 for properties of flat-rolled grain-oriented fully processed electrical steel. 1.1.3 Thin-gauge nonoriented electrical steels with a high silicon content (typically 61/28201;%) manufactured using silicon vapor-deposition or similar processes are not included in this specification. 1.2 The steel covered in this specification is produced to specified maximum core loss values and is intended primarily for use in rotating electrical machinery and other electromagnetic devices operating at moderate to elevated frequencies (100 Hz and greater). Desirable core loss and permeability characteristics are developed during mill processing; however, lamination manufacturing processes may adversely affect these mill-produced properties. Additional stress-relief heat treatment by the user may therefore be helpful in remediating these properties in the manufactured laminations. Stress-relief annealing is discussed further in Appendix X2. 1.3 These thin-gauge nonoriented fully processed electrical steels are low-carbon, silicon-iron, or silicon-aluminum-iron alloys typically containing 2.5 to 3.58201;% silicon and a small amount of aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Thin-Gauge Nonoriented Electrical Steel Fully Processed Types

YB/T 4321-2012 具有规定磁性能和力学性能的钢板及钢带

本标准规定了具有规定磁性能和力学性能的钢板及钢带的牌号、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、复验、数值修约、包装、标志及质量证明书等。本标准适用于旋转电机用磁性材料。

Steel sheets and strips with specified magnetic properties and mechanical properties

JIS C 2553:2012 交付到全加工状态的冷轧晶粒取向电工钢薄板和钢带

This Standard defines the grades of cold-rolled grain-oriented electrical steel strip and sheet with insulation coating on both sides in nominal thicknesses of 0.23mm, 0.27mm, 0.30mm and 0.35mm. In particular, it gives general requirements, magnetic properties, geometric characteristics, tolerances, technological characteristics, as well as inspection procedures.

Cold-rolled grain-oriented electrical steel strip and sheet delivered in the fully-processed state

IEC 60404-11:2012 磁性材料.第11部分:磁片和带材的表面绝缘电阻测定方法

Magnetic materials - Part 11: Method of test for the determination of surface insulation resistance of magnetic sheet and strip