H53 电工用钢 标准查询与下载

IEC 60404-11:1991/AMD2:2012 磁性材料.第11部分:磁带和磁条表面绝缘电阻测定的试验方法.修改件2

Magnetic materials - Part 11: Method of test for the determination of surface insulation resistance of magnetic sheet and strip; Amendment 2

ASTM A901-12 半成品型非晶形磁芯合金的标准规格

1.1 This specification covers the general requirements to which flat-cast, amorphous, semi-processed, iron-base magnetic core alloys must conform. 1.2 These alloys are produced by a rapid-quenching, direct-casting process, resulting in metals with noncrystalline (amorphous) structure. The metallic alloys are made to meet specified maximum core-loss values and are intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed by further heat treatment in a magnetic field by the user. The heat treatment typically consists of heating the material to a temperature of 320 to 420°C in a dry, inert atmosphere for 5 to 10 min, although soak times of up to 2 h may be used for large transformer cores. A magnetic field may be required during annealing as designated by the producer. Exact optimum annealing conditions depend on the processing of the material and the size and shape of the device. 1.3 Some of these alloys are sensitive to mechanical stress. Care must be exercised in minimizing any stresses on the material in its final application, otherwise, its magnetic properties will be significantly impaired. 1.4 This specification is developed to aid in the purchase of transformer grade amorphous strip. It provides the chemical, physical, and magnetic parameters and procedures for quality control tests. 1.5 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. Note 18212;For more information on procedures associated with this specification, refer to the following: Practices A34/A34M, A664, A700, and B490; Test Methods A370 and A773/A773M. 1.6 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Amorphous Magnetic Core Alloys, Semi-Processed Types

ASTM A677-12 全处理型无定向电工钢标准规格

1.1 This specification covers the detailed requirements to which flat-rolled nonoriented fully processed electrical steel shall conform. 1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed during mill processing, so additional heat treatment by the user is usually not necessary. 1.3 These nonoriented fully processed electrical steels are low-carbon, silicon-iron, or silicon-aluminum-iron alloys containing up to about 3.58201;% silicon and a small amount of aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel Fully Processed Types

ASTM A876-12 全加工型平轧的晶粒定向的硅铁电工钢

1.1 This specification covers the detailed requirements to which the specified grades of flat-rolled, grain-oriented, fully processed electrical steels shall conform. These steels are used primarily in transformer cores operating at moderate to high magnetic flux densities at commercial power frequencies (50 and 60 Hz). 1.2 These grain-oriented electrical steels are low-carbon, silicon-iron alloys with a silicon content of approximately 3.28201;% in which low core loss and high permeability in the direction of rolling have been achieved by appropriate metallurgical processing. 1.3 The electrical-steel grades described in this specification include (1) conventional grain-oriented electrical steel tested at 15 kG (1.5 T) in accordance with Test Method A343/A343M, (2) conventional grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Method A343/A343M, (3) high-permeability grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Method A343/A343M, and (4) laser-scribed high-permeability grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Methods A804/A804M. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.

Standard Specification for Flat-Rolled, Grain-Oriented, Silicon-Iron, Electrical Steel, Fully Processed Types

JIS C 2550-4:2011 电工钢条和电工钢板试验方法.第4部分:测定电工钢条和电工钢板表面绝缘特性试验方法

This Standard is applicable to the measuring methods of surface insulation resistance of electrical steel strip and sheet. This test method is applicable to electrical steel strip and sheet insulated on one or both surfaces, and is suitable for manufacturing control in the application of insulation coatings.

Test methods for electrical steel strip and sheet -- Part 4: Methods of test for the determination of surface insulation resistance of electrical strip and sheet

JIS C 2550-5:2011 电工钢条和电工钢板试验方法.第5部分:电工钢条和电工钢板密度,电阻率和堆垛系数的测量方法

This Standard specifies the measuring methods of density, resistivity and stacking factor of electrical steel strip and sheet. These quantities are necessary to establish the magnetic characteristics of the material. In particular, the density is necessary to allow specified values of the magnetic flux density to be set without knowing the thickness of the test specimen.

Test methods for electrical steel strip and sheet.Part 5: Methods of measurement of density, resistivity and stacking factor of electrical strip and sheet

JIS C 2550-3:2011 电工钢条和电工钢板试验方法.第3部分:中频时测量电工钢条和电工钢板磁特性测量方法

This Standard is applicable to the methods of measurement of the magnetic properties of electrical steel strip and sheet in the medium-frequency range of 400 Hz to 10 kHz under a.c. excitation.

Test methods for electrical steel strip and sheet -- Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet at medium frequencies

JIS C 2550-2:2011 电工钢条和电工钢板的试验方法.第2部分:电工钢条和电工钢板的几何特性测定方法

This Standard specifies the test methods for the determination of the following geometrical characteristics of electrical steel strip and sheet.

Test methods for electrical steel strip and sheet.Part 2: Methods of determination of the geometrical characteristics of electrical steel strip and sheet

JIS C 2550-1:2011 电工钢条和电工钢板试验方法.第1部分:采用爱普斯坦方圈测量电工钢条和电工钢板磁特性测量方法

This Standard is applicable to the measuring methods of magnetic properties of grain oriented and non-oriented electrical steel strip and sheet under a.c. excitation at frequencies up to 400 Hz and those under d.c. excitation.

Test methods for electrical steel strip and sheet.Part 1: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of an Epstein frame

ASTM A664-11 美国材料试验学会规范中鉴定标准电工钢等级的标准操作规程

1.1 This practice covers the procedure for designating (within ASTM specifications) standard grades of flat-rolled electrical steels made to specified maximum values of core loss. This practice applies to magnetically soft irons and steel (low-carbon steels and alloys of iron with silicon, aluminum, and so forth) where a core loss measurement at a stated peak value of alternating induction and a stated frequency, such as 15 kG (1.5 T) and 60 Hz, is normally used to grade the material. This practice also applies when some other property is specified (or a different induction or frequency, or both) as the limiting characteristic, provided the material also meets all the requirements of the ASTM specification. 1.2 Individual specifications that are in conformity with this practice are Specifications A677, A683, A726, and A876. 1.3 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications

IEC TR 62581:2010 电工钢.用单个薄片和艾普斯坦试样的磁致伸缩特性的测量方法

This technical report describes the general principles and technical details of the measurement of the magnetostriction of single sheet specimens preferably 500 mm long and 100 mm wide and Epstein strip specimens, specified in IEC 60404-2, of electrical steel by means of optical sensors and accelerometers. These methods are applicable to test specimens obtained from electrical steel sheets and strips of any grade. The characteristics of magnetostriction are determined for a sinusoidal induced voltage, for specified peak values of magnetic polarization and for a specified frequency. The measurements are made at an ambient temperature of 23 °C ± 5 °C on test specimens which have first been demagnetized.

Electrical steel - Methods of measurement of the magnetostriction characteristics by means of single sheet and Epstein test specimens

DIN IEC 60404-3:2010 磁性材料.第3部分:用单片测试仪对电气钢片和钢带磁性能的测量方法(IEC 60404-3-1992 + A1-2002 + A2-2009)

Magnetic materials - Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester (IEC 60404-3:1992 + A1:2002 + A2:2009)

IEC 60404-3:2010 电磁材料.第3部分:用单片钢板测试仪测量电钢带和钢片磁性能的方法

The object of this part is to define the general principles and the technical details of the measurement of the magnetic properties of magnetic sheets by means of a single sheet tester.

Magnetic materials – Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester (Edition 2.2 Consolidated Reprint)

ASTM A971/A971M-10 测量平滚轧电工钢卷材边缘锥度和凸面的标准试验方法

Flat-rolled electrical steel master coils are usually slit into narrower coils. Usually these slit coils are punched or sheared into laminations of various shapes. The laminations are then uniformly stacked to become the cores of magnetic devices such as motors and transformers. Stacking of many laminations exhibiting excessive taper causes assembly problems and poor appearance. Nonuniform stack lengths in motors cause imbalance and noise. When the laminations are interleaved in transformers, taper causes air spaces within the core resulting in increased noise, increased exciting current, and higher core loss.1.1 This test method provides a procedure for measuring edge taper and crown of flat-rolled electrical steel coils as produced at the steel mill. 1.2 The values and equations stated in customary (cgs-emu and inch-pound) units or SI units are to be regarded separately as standard. Within this standard, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard. 1.3 The following material specifications include requirements for edge taper or crown: A677, A683, A726, A840, and A876. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Edge Taper and Crown of Flat-Rolled Electrical Steel Coils

IEC 60404-3:1992/AMD2:2009 磁性材料.第3部分:用单片试验器测量磁钢片及磁钢带磁性能的方法.修改件2

Magnetic materials - Part 3: Methods of measurement of the magnetic properties of magnetic strip and sheet by means of a single sheet tester; Amendment 2

IEC 60401-2:2009 铁氧体软磁芯的术语和命名.第2部分:尺寸基准

Terms and nomenclature for cores made of magnetically soft ferrites - Part 2: Reference of dimensions

ASTM A876-09e1 全处理型平轧的晶粒取向的硅铁电工钢用的标准规格

1.1 This specification covers the detailed requirements to which the specified grades of flat-rolled, grain-oriented, fully processed electrical steels shall conform. These steels are used primarily in transformer cores operating at moderate to high magnetic flux densities at commercial power frequencies (50 and 60 Hz). 1.2 These grain-oriented electrical steels are low-carbon, silicon-iron alloys with a silicon content of approximately 3.2 % in which low core loss and high permeability in the direction of rolling have been achieved by appropriate metallurgical processing. 1.3 The electrical-steel grades described in this specification include (1) conventional grain-oriented electrical steel tested at 15 kG (1.5 T) in accordance with Test Method A343/A343M, (2) conventional grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Method A343/A343M, (3) high-permeability grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Method A343/A343M, and (4) laser-scribed high-permeability grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Methods A804/A804M. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.

Standard Specification for Flat-Rolled, Grain-Oriented, Silicon-Iron, Electrical Steel, Fully Processed Types

ASTM A876-09 全处理型平轧的晶粒取向的硅铁电工钢用标准规范

1.1 This specification covers the detailed requirements to which the specified grades of flat-rolled, grain-oriented, fully processed electrical steels shall conform. These steels are used primarily in transformer cores operating at moderate to high magnetic flux densities at commercial power frequencies (50 and 60 Hz). 1.2 These grain-oriented electrical steels are low-carbon, silicon-iron alloys with a silicon content of approximately 3.2 % in which low core loss and high permeability in the direction of rolling have been achieved by appropriate metallurgical processing. 1.3 The electrical-steel grades described in this specification include (1) conventional grain-oriented electrical steel tested at 15 kG (1.5 T) in accordance with Test Method A 343/A 343M, (2) conventional grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Method A 343/A 343M, (3) high-permeability grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Method A 343/A 343M, and (4) laser-scribed high-permeability grain-oriented electrical steel tested at 17 kG (1.7 T) in accordance with Test Methods A 804/A 804M. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.

Standard Specification for Flat-Rolled, Grain-Oriented, Silicon-Iron, Electrical Steel, Fully Processed Types

ASTM A345-09 磁设备用平轧电工钢的标准规范

1.1 This specification covers general procedures for specifying requirements in the procurement and delivery of flat-rolled electrical steels for magnetic applications. When an applicable individual specification does not exist, this specification enables the user to order a suitable material to be supplied under controlled conditions with respect to magnetic quality, sampling, testing, packaging, and so forth, by specifying certain requirements on the purchase order and citing this specification. 1.2 Individual ASTM electrical steel specifications that are in conformity with this specification are Specifications A677, A683, A726, A840, and A876. Note 18212;For more information on other standards associated with this specification, refer to the following: Test Methods A341/A341M, A343/A343M, A348/A348M, A596/A596M, A712, A717/A717M, A719/A719M, A720/A720M, A721/A721M, A773/A773M, A804/A804M, A889/A889M, A937/A937M, A971/A971M, and Practice A664. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Flat-Rolled Electrical Steels for Magnetic Applications

IEC 60404-4:1995/AMD2:2008 磁性材料.第4部分:软磁材料的直流磁性的测量方法.修改件2

This amendment has been prepared by IEC technical committee 68: Magnetic alloys and steels. The text of this amendment is based on the following documents: Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. The committee has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be ~ reconfirmed, ~ withdrawn, ~ replaced by a revised edition, or ~ amended.

Magnetic materials - Part 4: Methods of measurement of d.c. magnetic properties of magnetially soft materials; Amendment 2