H53 电工用钢 标准查询与下载

ASTM A664-06 在ASTM规范中对电工钢和层压钢级别的识别的标准操作规程

1.1 This practice covers the procedure for designating (within ASTM specifications) standard grades of flat-rolled electrical steels made to specified maximum values of core loss. This practice applies to magnetically soft irons and steel (low-carbon steels and alloys of iron with silicon, aluminum, and so forth) where a core loss measurement at a stated peak value of alternating induction and a stated frequency, such as 15 kG (1.5 T) and 60 Hz, is normally used to grade the material. This practice also applies when some other property is specified (or a different induction or frequency, or both) as the limiting characteristic, provided the material also meets all the requirements of the ASTM specification.1.2 Individual specifications that are in conformity with this practice are Specifications A 677, A 683, A 726, A 840/A 840M, and A 876.1.3 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications

ASTM A664-06e1 在ASTM规范中对电工钢和层压钢级别的识别的标准操作规程

1.1 This practice covers the procedure for designating (within ASTM specifications) standard grades of flat-rolled electrical steels made to specified maximum values of core loss. This practice applies to magnetically soft irons and steel (low-carbon steels and alloys of iron with silicon, aluminum, and so forth) where a core loss measurement at a stated peak value of alternating induction and a stated frequency, such as 15 kG (1.5 T) and 60 Hz, is normally used to grade the material. This practice also applies when some other property is specified (or a different induction or frequency, or both) as the limiting characteristic, provided the material also meets all the requirements of the ASTM specification.1.2 Individual specifications that are in conformity with this practice are Specifications A 677, A 683, A 726, A 840/A 840M, and A 876.1.3 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications

DIN EN 10107:2005 以完全加工状态交付的晶粒定向电工钢片和钢带

This European Standard is defines the grades of grain-oriented electrical sheet steel in nominal thicknesses of 0,23mm,0,27mm,0,30mm and 0,35mm. In particular, it gives general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as inspection procedures. This European Standard applies to Goss textured grain- oriented magnetic sheet steel supplied in the final annealed condition in sheets or coils, and intended for the construction of magnetic circuits.#,,#

Grain-oriented electrical steel sheet and strip delivered in the fully processed state; German version EN 10107:2005

DIN EN 10342:2005 磁性材料.电工钢板、带钢和叠层板材的表面绝缘分类

This standard establishes a classification of surface insulations for electrical steel sheet, strip and laminations according to their general composition, relative insulating ability and function.These surface insulations are either oxide layers or applied coatings.The purpose of this classification is to create a nomenclature for the various types of surface insulations.

Magnetic materials - Classification of surface insulations of electrical steel sheet, strip and laminations; German version EN 10342:2005

IEC 60404-8-3:2005 磁性材料.第8-3部分:单项材料规范.以半加工状态交货的冷轧电工非合金和合金钢片及钢带

Applies to magnetic material intended for the construction of magnetic circuits. These materials correspond respectively to classes C.21 and B.2 of IEC 60404-1: 2000. This standard defines the grades of cold-rolled electrical non-oriented non-alloyed (no

Magnetic materials - Part 8-3: Specifications for individual materials - Cold-rolled electrical non-alloyed and alloyed steel sheet and strip delivered in the semi-processed state

BS EN 10342:2005 磁性材料.电工钢片、带材和层压板材表面绝缘的分类

This document establishes a classification of surface insulations for electrical steel sheet, strip and laminations according to their general composition, relative insulating ability and function. These surface insulations are either oxide layers or applied coatings. The purpose of this classification is to create a nomenclature for the various types of surface insulations and to assist users of surface insulations by providing general information about the chemical nature and use of the surface insulations. It is not the intent of this classification to specify insulation requirements in terms of specific values of surface insulation resistance. Such requirements are to be agreed between the purchaser and the steel producer, where applicable. The classification is to be used in conjunction with the various specifications for cold rolled electrical steels (see the European Standards listed in Clause 2).

Magnetic materials - Classification of surface insulations of electrical steel sheet, strip and laminations

WJ 2666-2005 火炮用击发电磁铁型式尺寸

Type and size of firing electromagnet for artillery

ASTM A677-05e1 全处理型无取向电工钢的标准规范

1.1 This specification covers the detailed requirements to which flat-rolled nonoriented fully processed electrical steel shall conform.1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed during mill processing, so additional heat treatment by the user is usually not necessary.1.3 These nonoriented fully processed electrical steels are low-carbon, silicon-iron, or silicon-aluminum-iron alloys containing up to about 3.5 % silicon and a small amount of aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel Fully Processed Types

ASTM A683-05 半成品类无取向电工钢标准规范

1.1 This specification covers the detailed requirements to which flat-rolled, nonoriented semiprocessed electrical steel shall conform.1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed through heat treatment by the user. 1.3 These nonoriented, semiprocessed electrical steels are low carbon, silicon-iron or silicon-aluminum-iron alloys containing up to about 2.5 % silicon and less than 1 % aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types

ASTM A683-05e1 半成品类无取向电工钢标准规范

1.1 This specification covers the detailed requirements to which flat-rolled, nonoriented semiprocessed electrical steel shall conform.1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed through heat treatment by the user. 1.3 These nonoriented, semiprocessed electrical steels are low carbon, silicon-iron or silicon-aluminum-iron alloys containing up to about 2.5 % silicon and less than 1 % aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types

ASTM A677-05 全处理型无取向电工钢的标准规范

1.1 This specification covers the detailed requirements to which flat-rolled nonoriented fully processed electrical steel shall conform.1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed during mill processing, so additional heat treatment by the user is usually not necessary.1.3 These nonoriented fully processed electrical steels are low-carbon, silicon-iron, or silicon-aluminum-iron alloys containing up to about 3.5 % silicon and a small amount of aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel Fully Processed Types

ASTM A971/A971M-05 测量平滚轧电工钢卷材边缘锥度和凸面的标准试验方法

Flat-rolled electrical steel master coils are usually slit into narrower coils. Usually these slit coils are punched or sheared into laminations of various shapes. The laminations are then uniformly stacked to become the cores of magnetic devices such as motors and transformers. Uniform stacking of many laminations exhibiting excessive taper causes assembly problems and poor appearance. Nonuniform stack lengths in motors cause imbalance and noise. When the laminations are interleaved in transformers, taper causes air spaces within the core resulting in increased noise, exciting current, and core loss.1.1 This test method provides a procedure for measuring edge taper and crown of flat-rolled electrical steel coils as produced at the steel mill.1.2 The values and equations stated in customary (cgs-emu and inch-pound) units or SI units are to be regarded separately as standard. Within this standard, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard.1.3 The following material specifications include requirements for edge taper or crown: A 677, A 683, A 726, A 840/A 840M, and A 876.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Edge Taper and Crown of Flat-Rolled Electrical Steel Coils

ASTM A726-05 半成品型冷轧磁性迭片钢的标准规范

1.1 This specification covers cold-rolled carbon sheet steel used for magnetic applications. These products, commonly called "cold-rolled magnetic lamination steel" (CRML) are usually intended for applications in which the stamped laminations or assembled core structures for electrical equipment are annealed to develop the desired core loss and permeability characteristics.1.2 By using appropriate lamination annealing practices, the user can optimize magnetic properties for the various types.1.3 Non-guaranteed core-loss types, usually made to controlled chemical compositions, are available but are not covered by this specification.1.4 Higher quality core-loss types are made to controlled chemical compositions and are usually given a critical reduction on a temper-mill to yield specified magnetic properties after a suitable lamination anneal. These products, typically called semiprocessed lamination steel, are classified by the ASTM Code Letter D in accordance with Practice A 664.1.5 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

Standard Specification for Cold-Rolled Magnetic Lamination Quality Steel, Semiprocessed Types

ASTM A726-05(2010) 半成品型冷轧磁性迭片级钢的标准规格

1.1 This specification covers cold-rolled carbon sheet steel used for magnetic applications. These products, commonly called “cold-rolled magnetic lamination steel” (CRML) are usually intended for applications in which the stamped laminations or assembled core structures for electrical equipment are annealed to develop the desired core loss and permeability characteristics. 1.2 By using appropriate lamination annealing practices, the user can optimize magnetic properties for the various types. 1.3 Non-guaranteed core-loss types, usually made to controlled chemical compositions, are available but are not covered by this specification. 1.4 Higher quality core-loss types are made to controlled chemical compositions and are usually given a critical reduction on a temper-mill to yield specified magnetic properties after a suitable lamination anneal. These products, typically called semiprocessed lamination steel, are classified by the ASTM Code Letter D in accordance with Practice A664. 1.5 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

Standard Specification for Cold-Rolled Magnetic Lamination Quality Steel, Semiprocessed Types

ASTM A683-05(2010) 半成品无取向电工钢的标准规格

1.1 This specification covers the detailed requirements to which flat-rolled, nonoriented semiprocessed electrical steel shall conform. 1.2 This steel is produced to specified maximum core-loss values and is intended primarily for commercial power frequency (50- and 60-Hz) applications in magnetic devices. Desirable core-loss and permeability characteristics are developed through heat treatment by the user. 1.3 These nonoriented, semiprocessed electrical steels are low carbon, silicon-iron or silicon-aluminum-iron alloys containing up to about 2.5 % silicon and less than 1 % aluminum. 1.4 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types

DIN EN 60404-6:2004 磁性材料.第6部分:使用环形样品的频率范围在20 Hz 到 200 kHz的磁性软金属和粉末材料的磁性能测量方法

This part of IEC 60404 specifies methods for the measurement of a.c. magnetic properties of materials in the frequency range 20 Hz to 200 kHz other than electrical steels and soft ferrites. The materials covered by this part of IEC 60404 include those speciality alloys listed in IEC 60404-8-6, amorphous and nanocrystalline materials, pressed and sintered and metal injection moulded parts such as are listed in IEC 60404-8-9, cast parts and magnetically soft composite materials.#,,#

Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range of 20 Hz to 200 kHz by the use of ring specimens (IEC 60404-6:2003); German version EN 60404-6:20

IEC 60404-8-1:2004 磁性材料.第8-1部分:单项材料规范.硬磁材料

Specifies minimum values for the principal magnetic properties of, and dimensional tolerances for, technically important magnetically hard materials (permanent magnets). For information purposes only, the standard provides values for the densities of the

Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials

IEC 60404-8-1:2001/AMD1:2004 磁性材料.第8-1部分:单项材料规范.硬磁材料.修改件1

This standard is Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials; Amendment 1.

Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials; Amendment 1

IEC 60404-1-1:2004 磁性材料.第1-1部分:分类.电工钢薄板、带材和叠层板材的表面绝缘

Establishes a classification of surface insulations for electrical steel sheet, strip and laminations according to their general composition, relative insulating ability and function. These surface insulations are either oxide layers or applied coatings.

Magnetic materials - Part 1-1: Classification - Surface insulations of electrical steel sheet, strip and laminations

ASTM A801-04 锻造铁-钴高磁饱和合金的标准规范

1.1 This specification covers two wrought iron-cobalt alloy types currently manufactured and supplied commercially for use in magnetic components requiring high permeability at and above 15 kG (1.5 T) or high magnetic saturation. The specific alloy types covered are:Alloy TypeUNSNominal Composition1R3000549 % Co, 49 % Fe, 2 % V2K9265027 % Co, 0.50 % Cr, balance Fe1.1.1 This specification also covers material supplied by a producer in the form and physical condition suitable for fabrication into parts that will later be given final heat treatment to achieve the desired magnetic characteristics and, where required, mechanical properties. It covers material supplied in form of forging billets, hot-rolled products, cold-finished bars, and strip.1.2 This specification does not cover parts produced by casting or by powder metallurgical techniques.1.3 The values stated in customary (cgs-emu and inch-pound) units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

Standard Specification for Wrought Iron-Cobalt High Magnetic Saturation Alloys (UNS R30005 and K92650)