J95 润滑系统 标准查询与下载

JB/T 7908-1999 内燃机粉末冶金机油泵转子.技术条件

本标准规定了内燃机粉末冶金机油泵转子的技术要求，试验方法，检验规则及标志、包装、运输、贮存等内容。 本标准适用于工作压力不大于0.5 MPa的内燃机机油泵。

Specifications for P/M oil pump rotor of the internal combustion engines

ARMY MIL-PRF-46736 E-1998 干燥型吸入式空气滤清器元件

This specification covers dry type air cleaner filter elements used in single and multi-stage air cleaners(see 6.1).

FILTER ELEMENT, INTAKE AIR CLEANER: DRY TYPE

BS 7403-3:1998 用于内燃机的全流式润滑油过滤器 耐高压差和耐高温试验方法

This part of ISO 4548 specifies tests for measuring the resistance to high differential pressure and the resistance to elevated temperatures of filter elements of full-flow lubricating oil filters for internal combustion engines.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for resistance to high differential pressure and to elevated temperature

BS 7403-11:1998 用于内燃机的全流式润滑油过滤器 自清洁过滤器的测试方法

This part of ISO 4548 specifies test methods for evaluating the characteristics of self-cleaning oil filters for internal combustion engines. It is applicable to filters in which self-cleaning is continuous or intermittent. The removal of retained particles from the filter is achieved by periodic reversal of the direction of the fluid flow through the elements. However, this also applies mechanical stresses to the filter media. The tests specified in this standard are designed to check the filtration performance of the elements under simulated operating conditions and to confirm their ability to withstand, without damage, variations in oil pressure, temperature, direction of flow and the presence of water. The equipment and procedures specified in this part of ISO 4548 are recommended for filters having a nominal flow rate of up to 1 600 l/min.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for self-cleaning filters

ANSI/ANS 59.52-1998 安全相关应急柴油发电机用润滑油系统

This standard provides functional, performance, and design requirements for lubricating oil systems for diesel generators that provide emergency onsite power for light water reactor nuclear power plants. The standard addresses all mechanical equipment associated with the lubricating oil system, with the exception of engine mounted components. These components, which are mounted directly to engine structure itself, are excluded, except to define interface requirements. This standard also includes the lubricating oil system instrumentation and control functional requirements.

Lubricating Oil Systems for Safety-Related Emergency Diesel Generators

ISO 4548-4:1997 内燃机全流式机油滤清器试验方法 第4部分:原始容灰量、滤芯寿命和累积效率(重量法)

This part of ISO 4548 specifies tests for determining the performance of full-flow lubricating oil filters for internal combustion engines as follows. Section 2: Initial particle retention efficiency. This gives the test procedures and parameters for the determination of the initial particle retention efficiency of lubricating oil filter elements under defined test conditions. By reporting the results in accordance with subclause 2.6, the probable retention efficiency for any particle size may be derived. The retention efficiency is determined by the gravimetric method. Section 3: Life and cumulative efficiency. This gives the test procedures and parameters for the determination of element life and cumulative efficiency of lubricating oil filters. The cumulative efficiency is determined by the gravimetric method. NOTE — By agreement between filter manufacturer and purchaser, tests on large filters can be conducted on the basis of tests carried out on filters scaled-down in length. The relationship of the filter flow and test dust addition rate to the effective length of the filter medium should be the same in the scaled-down tests as in the full size filter. For the purposes of this part of ISO 4548, a filter having a test flow rate exceeding 100 l/min is considered large.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 4: Initial particle retention efficiency, life and cumulative efficiency (gravimetric method)

ISO 4548-1:1997 内燃机全流式机油滤清器试验方法 第1部分:压差/流量特性

This part of ISO 4548 specifies tests for determining the differential pressure/flow characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of a filter with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 1: Differential pressure/flow characteristics

ISO 4548-3:1997 内燃机全流式机油滤清器试验方法 第3部分:耐高压差和耐高温性

This part of ISO 4548 specifies tests for measuring the resistance to high differential pressure and the resistance to elevated temperatures of filter elements of full-flow lubricating oil filters for internal combustion engines.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 3: Resistance to high differential pressure and to elevated temperature

ISO 4548-2:1997 内燃机全流式机油滤清器试验方法 第2部分:滤芯旁通阀特性

This part of ISO 4548 specifies tests for determining the element by-pass valve characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of an element by-pass valve with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 2: Element by-pass valve characteristics

ISO 4548-11:1997 内燃机全流式机油滤清器试验方法 第11部分:自洁式滤清器

This part of ISO 4548 specifies test methods for evaluating the characteristics of self-cleaning oil filters for internal combustion engines. It is applicable to filters in which self-cleaning is continuous or intermittent. The removal of retained particles from the filter is achieved by periodic reversal of the direction of the fluid flow through the elements. However, this also applies mechanical stresses to the filter media. The tests specified in this standard are designed to check the filtration performance of the elements under simulated operating conditions and to confirm their ability to withstand, without damage, variations in oil pressure, temperature, direction of flow and the presence of water. The equipment and procedures specified in this part of ISO 4548 are recommended for fitters having a nominal flow rate of up to 1 600 l/min.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 11: Self-cleaning filters

KS B 6344-1996 油压系统.囊式蓄能器

이 규격은 기계 설비에 사용하는 유압 시스템에 사용되는 유압용 블래더 형식의 세퍼레이터를

Oil hydraulic system- Bladder type accumulators

JB/T 8414-1996 内燃机机油泵传动轴端的型式和尺寸

本标准规定了机油泵传动轴端的型式和尺寸。 本标准适用于中小功率内燃机机油泵(包括齿轮泵和转子泵)的传动轴端的设计和制造。

Type and size of oil pump drive shaft end of internal-combustion engine

JB/T 8413-1996 内燃机油泵 技术条件

本标准规定了内燃机用外啮合渐开线齿轮泵总成和内啮合摆线齿轮泵总成的技术要求，检验规则和标志、包装、运输、储存。 本标准适用于内燃机用齿轮泵和转子泵。内啮合渐开线齿轮泵可参照本标准。

Specifications for internal combustion engine oil pumps

BS 7403-9:1995 内燃机用全流式润滑油过滤器.入口和出口防泄油阀试验方法

Method of measuring the effectiveness of anti-drain valves if fitted to spin-on or easy change type oil filters.

Full-flow lubricating oil filters for internal combustion engines - Method of test for inlet and outlet anti-drain valves

ISO 4548-9:1995 内燃机全流式机油滤清器试验方法 第9部分:进、出口止回阀试验

Specifies methods of measuring the effectiveness of either inlet or outlet anti-drain valves if fitted to a full-flow lubricating oil filter of the "spin-on" or "easy change" type, for internal combustion engines.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 9: Inlet and outlet anti-drain valve tests

JB/T 7451-1994 静压支承润滑系统供油装置 技术条件

本标准规定了静压支承供油装置的技术条件，检验方法，检验规则及标志、包装与贮存。 本标准适用于以运动粘度为2～68mm^(2)/s的油液为工作介质的金属切削机床静压支承润滑系统恒压供油装置。

Specifications of oil supply device for hydrostatic bearing lubrication system

JB/T 7452-1994 数控机床润滑系统供油装置 技术条件

本标准规定了数控机床集中润滑系统连续与间歇供油装置的技术条件，检验方法，检验规则，标志、包装、贮存。 本标准适用于数控机床、精密机床，以粘度为22～100mm^(2)/s精制矿物油为工作介质的润滑系统连续及间歇供油装置，也适用于一般机床及机械设备的润滑供油装置。

Specifications of oil supply device for lubricating system of CNC machine tool

JB/T 6725-1993 内燃机旋装式机油滤清器 试验方法

本标准规定了测试内燃机旋装式机油滤清器性能的试验项目、装置、方法和程序。 本标准适用于体积流量为50L/min以下的内燃机旋装式机油滤清器。

Test methods for spin-on oil filters for internal combustion engines

BS 6580:1992 发动机冷冻剂浓缩物(防冻剂)防腐规范

Minimum performance requirements for concentrates intended for use at appropriate dilutions in the cooling systems of all types of liquid-cooled internal combustion engine.

Specification for corrosion inhibiting, engine coolant concentrate ('antifreeze')

JB/T 6005-1992 内燃机机油泵转子系列参数

Internal Combustion Engine Oil Pump Rotor Series Parameters