K47 输电线路器材 标准查询与下载

DB43/T 1808-2020 连续缠绕铺放玻璃纤维增强塑料电缆导管技术规范

Technical specifications for continuous winding and laying of glass fiber reinforced plastic cable ducts

DL/T 1995-2019 变电站换流站带电作业用绝缘平台

Insulation platform for live working in substation converter station

DL/T 1889-2018 输电杆塔用紧固件横向振动试验方法

Lateral vibration test method for fasteners used in transmission towers

DL/T 1147-2018 电力高处作业防坠器

Fall arrest device for electric power work at heights

ASTM B524/B524M-18 铝合金增强同心绞合铝导线的标准规范(ACAR 1350/6201)

1.1 This specification covers concentric-lay-stranded conductors made from round aluminum 1350-H19 (extra hard) wires and round aluminum-alloy 6201-T81 (hard: solution heat treated, cold worked, and then artificially aged) core wires for use as overhead electrical conductors (Explanatory Note 1). Note 1: The aluminum, alloy, and temper designations conform to ANSI H35.1/ANSI H35.1[M]. Aluminum 1350 and Alloy 6201 correspond to unified numbering system A91350 and A96201, respectively, in accordance with Practice E527. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Alloy Reinforced (ACAR, 1350/6201)

ASTM B549-18 架空电导体用铝包钢增强同心绞合铝导体的标准规范

1.1 This specification covers concentric-lay-stranded conductors made from round aluminum 1350-H19 (extra hard) aluminum wires and round aluminum-clad steel core wires for use as overhead electrical conductors (Explanatory Note 1 and Note 2). 1.2 The SI values of density and resistivity are to be regarded as standard. For all other properties the inch-pound units are regarded as standard and the SI units may be approximate. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Clad Steel Reinforced for Use in Overhead Electrical Conductors

DL/T 1781-2017 电力器材质量监督检验技术规程

Technical regulations for quality supervision and inspection of electrical equipment

DL/T 1740-2017 直流气体绝缘金属封闭输电线路技术条件

Specifications for DC gas-insulated metal-enclosed transmission lines

DL/T 5755-2017 沙漠地区输电线路杆塔基础工程技术规范

Technical specifications for foundation engineering of transmission line towers in desert areas

DIN VDE 0212-470:2017 架空线路用配件.第470部分:轭板

Yoke plates according to this standard are used preferably for overhead electrical lines and switchgears and controlgears with nominal system voltages exceeding AC 1 kV and DC 1,5 kV.

Fittings for overhead lines - Part 470: Yoke Plate

DL/T 768.4-2017 电力金具制造质量 第4部分：球墨铸铁件

Manufacturing quality of electrical fittings - Part 4: Ductile iron castings

DL/T 768.2-2017 电力金具制造质量 第2部分：黑色金属锻制件

Manufacturing quality of electrical fittings - Part 2: Forgings of ferrous metals

DL/T 768.3-2017 电力金具制造质量 第3部分：冲压件

Manufacturing quality of electric power fittings part 3: Stamping parts

DL/T 768.5-2017 电力金具制造质量 第5部分：铝制件

Manufacturing quality of electrical fittings - Part 5: Aluminum parts

DIN VDE 0212-474:2017 架空线路用配件. 第474部分:榫舌和U形夹. 接头尺寸

Fittings for overhead lines - Part 474: Tongue and clevis - Dimensions of couplings

DIN VDE 0212-478:2017 架空线路用配件.第478部分:U形搭接线

Fittings for overhead lines - Part 478: Clevis straps

DIN VDE 0212-459:2017 架空线路用配件.第459部分:双端球形销

Fittings for overhead lines - Part 459: Twin balled pins

DIN VDE 0212-469:2017 架空线路用配件.第469部分:双环

Fittings for overhead lines - Part 469: Double eyes

DIN VDE 0212-473:2017 架空线路用配件.第473部分:连接螺栓

Fittings for overhead lines - Part 473: Connecting bolts

DIN VDE 0212-465:2017 架空线路用配件.第465部分:球头挂环

Fittings for overhead lines - Part 465: Ball eyes