K47 输电线路器材 标准查询与下载

DL/T 763-2013 架空线路用预绞式金具技术条件

Specifications for pre-twisted fittings for overhead lines

IEC 60743:2013 带电作业.工具、设备和装置术语

Live working - Terminology for tools, devices and equipment

DIN EN 40-3-1:2013 灯柱.第3-1部分:设计和验证.特征和在规范.德文版本EN 40-3-1-2013

Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads; German version EN 40-3-1:2013

DIN EN 40-3-3:2013 灯柱.第3-3部分:设计和检验.通过计算检定.德文版本EN 40-3-3-2013

Lighting columns - Part 3-3: Design and verification - Verification by calculation; German version EN 40-3-3:2013

DIN EN 60900:2013 带电作业.交流电1000 V和直流1500 V以的带电作业用手持工具(IEC 60900-2012).德文版本EN 60900-2012

Live working - Hand tools for use up to 1 000 V a.c. and 1 500 V d.c. (IEC 60900:2012); German version EN 60900:2012

BS EN 62488-1:2013 电力应用电力线通信系统.EHV/HV/MV电力网络操作模拟和数字电力载波线系统规划

Power line communication systems for power utility applications. Planning of analogue and digital power line carrier systems operating over EHV/HV/MV electricity grids

DL/T 1248-2013 架空输电线路状态检修导则

本标准规定了架空输电线路的检修分类及检修项目、状态检修策略、状态检修计划、线路状态检修项目实施等。本标准适用于110 (66) kV及以上电压等级交流架空输电线路的状态检修;35kV交流架空输电线路以及直流架空输电线路可参考采用。

Guide for condition based maintenance strategy of overhead transmission line

DL/T 1249-2013 架空输电线路运行状态评估技术导则

本标准规定了架空输电线路运行单元划分、状态量描述、状态量变化和状态评估等。本标准适用于110 (66) kV及以上电压等级的架空输电线路(简称“线路”)运行状态的技术评估工作;35kV线路可参考采用。

Guide for running state assessment strategy of overhead transmission line

DL/T 767-2013 全介质自承式光缆(ADSS)用预绞式金具技术条件和试验方法

本标准规定了全介质自承式光缆(简ADSS)用预绞式金具的型式、技术条件和试验方法等内容。本标准适用于采用预绞方式安装在ADSS上的悬垂线夹、耐张线夹、防护金具等预绞式金具。

Technical requirements and tests for helical fittings of ADSS

DL/T 5154-2012 架空输电线路杆塔结构设计技术规定

Technical regulation of design for tower and pole structures of overhead transmission line

ASTM B701/B701M-13(2018) 钢增强同心绞合自阻尼铝导线的标准规范(ACSR/SD)

1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor, steel-reinforced (ACSR/SD), and its component wires for use as overhead electrical conductors (Explanatory Notes 1 and 2). 1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. For conductor sizes designated by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units. 1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard. Note 1: ACSR/SD is designed to control aeolian vibration by integral damping. The conductors consist of a central core of a round steel wire or wires surrounded by two layers of trapezoidal aluminum 1350-H19 wires or two layers of trapezoidal aluminum 1350-H19 wires and one layer of round aluminum 1350-H19 wires (Fig. 1). The trapezoidal-wire layers are separated from each other and from the steel core by two small annular gaps that provide the conductors self-damping characteristics. The round aluminum wires are in tight layer contact between themselves and the underlying trapezoidal wire layer. Different strandings of the same size of conductor are identified by type, which is the approximate ratio of steel area to aluminum area, expressed in percent (Table 1 and Table 2). FIG. 1 Illustrations of Typical ACSR/SD Strandings Note 2: The aluminum and temper designations conform to ANSI Standard H8201;35.1. Aluminum 1350 corresponds to UNS A91350 in accordance with Practice E527. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD)

ANSI/UL 1565-2013 定位装置安全性标准(提案日期 9-28-12)

Standard for Safety for Positioning Devices (Proposal dated 9-28-12)

BS EN 60900:2012 带电作业.供使用的小于交流1000 V和直流1500 V的手工工具

Live working. Hand tools for use up to 1000 V a.c. and 1500 V d.c

DL/T 1179-2012 lOOOkV交流架空输电线路工频参数测量导则

本标准规定了 1000kV 交流架空輸电線路工頻參數的工頻測量技术方法。 本标准适用于 1000kV 交流架空輸电線路工頻參數的測量，750kV 及以下交流架空輸电線路工頻參 數的測量也可參考使用。

Guide for power frequency parameters measurement of 1,000 kV AC overhead transmission lines

DL/T 1184-2012 lOOOkV输电线路铁塔、导线、金具和光纤复合架空地线监造导则

The guide of supervision for manufacturing 1,000 kV transmission line tower, conductors, electric power fittings and optical fibre composite overhead ground wire

DL/T 1187-2012 lOOOkV 力空输电线路电磁环境控制值

本标准规定了 1000kV 架空輸电線路的工頻电场、工频磁场、无线电干扰和可听噪声控制值。 本标准适用于标称电压为 1000kvV 的架空输电线路。

Control levels for electromagnetic environment producted by 1,000 kV overhead transmission line

DL/T 1192-2012 架空输电线路接续管保护装置

Protector for splicing fitting of overhead transmission line

NF C18-400:2012 带电作业.交流1000 V和直流1500 V以下带电作业用手工工具

Live working - Hand tools for use up to 1 000 V a.c. and 1 500 V d.c

DIN VDE V 0212-474:2012 架空线路用配件. 榫舌和U形夹. 接头尺寸

Fittings for overhead lines - Tongue and clevis - Dimensions of couplings

DIN VDE V 0212-469:2012 架空线路用配件. 双环

Fittings for overhead lines - Double eyes