K54 汽轮机及其辅助设备 标准查询与下载

ANSI/ASME PTC39.1-2005 凝水排除器

This Code covers steam traps which are devices used in removing condensate and non-condensibles from steam systems.

Steam Traps

DL/T 905-2004 汽轮机叶片焊接修复技术导则

Technical guide for repair welding of turbine blades

JIS B 0127:2004 火力发电厂术语汇编.火力和地热发电厂的汽轮机和辅助设备

この規格は，火力発電で用いられる蒸気タービン及び附属装置，並びに地熱発電設備に関する用語について規定する。備考 この規格の用語は，原子力発電用，コンバィンドサイクル発電用，並びに一般産業用に使用している蒸気タービン設備及び附属装置に適用してもよい。

Glossary of terms for thermal power plant -- Steam turbines and auxiliary equipment of thermal and geothermal power plant

JIS B 8105:2004 蒸汽涡轮机.验收试验.改型蒸汽涡轮机的热性能检查试验

この規格は，蒸気タービン及び蒸気タービン設備に，幾つかの設備変更を伴う改造を行った改造蒸気タービンの性能確認方法について，次の事項の保証値を実証するため，発電用の過熱及び湿り蒸気タービンの試験の実施，並びに試験結果の計算方法について規定する。

Steam turbines -- Acceptance test -- Thermal performance verification tests of retrofitted steam turbines

ASME PTC 6-2004 蒸汽轮机.勘误表:2/2006

This Code provides procedures for the accurate testing of steam turbines. It is recommended for use in conducting acceptance test of steam turbines and any other situation in which performance levels must be determined with minimum uncertainty. It may be used for testing of steam turbines operating either with a significant amount of superheat in the initial steam (typically fossil-fueled units) or predominantly within the moisture region (typically nuclear- fueled units). This Code contains rules and procedures for the conduct and reporting of steam turbine testing, including mandatory requirements for pretest arrangements, instruments to be employed, their application and methods of measurement, testing techniques, and methods of calculation of test results. The performance parameters which may be determined from a Code test include: (a) heat rate, (b) generator output, (c) steam flow, (d) steam rate, (e) feedwater flow. It also contains procedures and techniques required to determine enthalpy values within the moisture region and modifications necessary to permit testing within the restrictions of radiological safety requirements in nuclear plants.

Steam Turbines Erratum: 2/2006

ANSI/ASME PTC6-2004 汽轮机的性能试验标准6

This code may be used for testing of steam turbines operating either with a significant amount of superheat in the initial steam (typically fossil fueled units) or predominantly within the moisture region (typically nuclear fueled units). This code contains rules and procedures for the conduct and reporting of steam turbine testing, including mandatory requirements for pretest arrangements, instruments to be employed, their application and methods of measurement, testing techniques, and methods of calculation of test results. The performance parameters which may be determined from a Code test include: (a) heat rate, (b) generator output; (c) steam flow, (d) steam rate, (e) feedwater flow. It also contains procedures and techniques required to determine enthalpy valves within the moisture region and modifications necessary to permit testing within the restrictions of radiological safety requirements in nuclear plants.

Performance Test Code 6 on Steam Turbines

ASME PTC 6.2-2004 组合循环中蒸汽涡轮机

This Code may be used for testing steam turbines in combined cycles with or without supplementary firing and in cogeneration applications. Within these categories of combined and cogeneration cycles, this Code is applicable to condensing and noncondensing steam turbines, to reheat and nonreheat steam turbines, and to induction/ extraction steam turbines. The variety of cycles presents challenges in writing a code that addresses all issues encountered for all cycle configurations. ASME PTC 6 is the appropriate code for testing steam turbines in nuclear and fossil- fired regenerative feedwater heater cycles. This Code is applicable only to turbines in cycles in which steam is the working fluid. This Code provides procedures for testing and calculating turbine-generator output performance corrected to reference conditions as a measure of overall turbine performance. This Code contains rules and procedures for the conduct and reporting of steam turbine testing, including requirements for pretest arrangements, testing techniques, instrumentation, methods of measurement, and methods for calculating test results and uncertainty.

Steam Turbines in Combined Cycles

JIS B 8101:2003 汽轮机规范

この規格は，発電用蒸気タービン(以下，タービンという。)の一般仕様について規定する。なお，この規格をその他の用途の蒸気タービンに適用してもよい。

Specifications for steam turbines

NF C55-553-1*NF EN 60953-1:2002 汽轮机热力验收试验规则.第1部分:方法 A:大容量冷凝式汽轮机的高精度

Rules for steam turbine thermal acceptance tests - Part 1 : Method A - High accuracy for large condensing steam turbines.

ISO 14661:2000/Amd 1:2002 工业用热涡轮机(蒸汽涡轮机、气体膨胀式轮机).一般要求.修改件A1:工业用热涡轮机数据表

This is Amendment 1 to ISO 14661-2000 (Thermal turbines for industrial applications (steam turbines, gas expansion turbines) — General requirements — )

Thermal turbines for industrial applications (steam turbines, gas expansion turbines) - General requirements; Amendment A1: Data sheets for thermal turbines for industrial applications

BS DD IEC TS 61370:2002 蒸汽轮机.蒸汽纯度

This technical specification describes the importance of the chemical characteristics of steam supplied to steam turbines and the need to prevent corrosion and deposition in steam space, in order to minimize the risk of turbine corrosion failures or loss of efficiency or output. The significance of relevant chemical parameters, mostly related to impurity levels, is discussed in terms of types of plant and chemistry operating regimes. This specification is applicable to turbines of all electrical output rating and any exhaust condition, i.e. condensing or back pressure. However, the range of application in terms of output rating or steam pressure is dictated by economic factors such as the relative cost of monitoring equipment and turbine plant. It is designed for new plant, but may be adapted for use on existing plant.

Steam turbines - Steam purity

IEC TS 61370:2002 蒸汽汽轮机.蒸汽纯度

This technical specification describes the importance of the chemical characteristics of steam supplied to steam turbines and the need to prevent corrosion and deposition in steam space, in order to minimize the risk of turbine corrosion failures or loss

Steam turbines - Steam purity

BS EN 60953-3:2002 汽轮机热力验收试验规则.改装的汽轮机的热性能验证试验

Rules for steam turbine thermal acceptance tests - Thermal performance verification tests of retrofitted steam turbines

JIS B 8102:2002 汽轮机.验收试验

この規格は，蒸気タービン及び蒸気タービン設備に関する次の事項の保証値を実証するため，発電用の過熱及び湿り蒸気タービンの試験の実施，並びに試験結果の計算に対して規定する。なお，発電用以外の蒸気タービンに，この規格を適用してもよい。

Steam turbines -- Acceptance test

IEC 60953-3:2001 气轮机热力性能验收试验规则 第3部分：改型气轮机的热性能验证试验

This part of IEC 60953, also called "retrofit code" (RC), establishes a supplementary retrofit code for thermal verification tests of retrofitted steam turbines. The rules given in this standard follow the guidance given in IEC 60953-2, hereinafter called the RS but contain amendments and supplements regarding guarantees and verification of the guarantees by thermal acceptance tests on retrofitted steam turbines. General principles for the preparation, performance, evaluation, comparison with guaranteed values and the determination of the measurement uncertainties of verification tests are given in this standard. This standard is applicable only when the retrofit involves some hardware change in the steam turbine equipment. Conversely, any modification on the cycle or any retrofit of other equipment of the power plant (e.g. boiler, feedwater heaters, etc.) is not covered by this standard.

Rules for steam turbine thermal acceptance tests - Part 3: Thermal performance verification tests of retrofitted steam turbines

JB/T 10087-2001 汽轮机承压铸钢件技术条件

　　本标准规定了汽轮机承压铸钢件(承压铸钢件包括汽缸、主汽阀、调节阀、蒸汽室、喷嘴室)的技术要求、试验和检验方法、标识及合格证书等。 　　本标准适用于汽轮机孙压铸钢件的订货、制造和检验。本标准不适用于300MW及300MW以上的汽轮机缸体铸钢件。

Specifications for steel casting of steam turbines for pressure purposes

JB/T 10086-2001 汽轮机调节（控制）系统技术条件

　　本标准规定了汽轮机调节(控制)系统的定义和技术要求。 　　本标准适用于固定式发电用汽轮机调节(控制)系统，其它型式汽轮机调节(控制)系统可参照使用。

Technical requirements for steam turbine governing(control) system

JB/T 3596-2001 射水抽气器 性能试验规程

　　本标准规定了凝汽设备抽除空气和其它不凝结气体的射水抽气器的性能试验方法，用以测定不同工作水压力、温度下，抽吸的干空气流量与吸入侧压力之间的关系，抽气器耗功等。 　　本标准适用于火力发电站汽轮机凝汽设备的抽气器。

Performance test code for water jet air ejectors

JB/T 4056-2001 射汽抽气器 性能试验规程

本标准规定了凝汽设备抽除空气或其它不凝结气体的单级或多级射汽抽气器的性能试验方法。 本标准适用于火力发电站和核电站汽轮机凝汽设备的抽气器。

Performance test code for Steam-operated air ejectors

ASME PTC 6A-2001 蒸汽涡轮机试验规程.PTC 6的补充

Test Code for Steam Turbines-Appendix to PTC 6.