K56 燃气轮机及其辅助设备 标准查询与下载

KS B ISO 3977-3:2015 燃气轮机.采购.第3部分:设计要求

Gas turbines — Procurement — Part 3: Design requirements

BS ISO 19372:2015 微型涡轮机应用 安全

Microturbines applications. Safety

ASME PTC 22-2014 燃气涡轮机的性能试验规则

The new edition of PTC 22 is intended to be a more thorough and accurate approach to the thermal performance testing of gas turbines based on industry feedback and harmonization with other codes and standards. To more completely support testing of gas turbines in a broad range of applications, this edition includes significant changes from previous to incorporate methodology for determination of gas turbine exhaust energy, flow, and temperature. PTC 22 establishes directions and rules for conduct and results reporting of thermal performance tests for open cycle gas turbine power plants and gas turbine engines. This performance test code provides explicit instruction on determining corrected power, heat rate, exhaust flow, exhaust energy, and exhaust temperature. Guidance is also provided for designing testing requirements and programs to satisfy different goals such as absolute performance and comparative performance. It is the intent of this performance test code to provide results with the highest level of accuracy consistent with the best engineering knowledge and practice in the gas turbine industry. In planning the test, an uncertainty analysis must demonstrate that the proposed instrumentation and measurement techniques meet the requirements of the Code. PTC 22 is used in power plants worldwide and is recognized internationally. This performance test code was developed by a committee with balanced membership from manufacturers, power plant owners and operators, design engineers, and general interest groups.

Performance Test Code on Gas Turbines

JIS B 8124:2013 燃气发动机驱动的废能发电包组件的要求

Requirements of the components of the gas engine driven cogeneration package

ASME TDP-1-2013 发电用蒸汽涡轮机的水损坏预防:化石燃料厂

ASME?s TDP-1 Standard provides recommended practices for the prevention of water damage to steam turbines used in fossil-fuel-fired electrical power generation. These practices address damage due to water, wet steam, and steam backflow into a steam turbine and are applicable to conventional steam cycle, combined cycle and cogeneration plants. They cover design, operation, inspection, testing, and maintenance of those aspects of the following power plant systems and equipment concerned with preventing the induction of water into steam turbines and associated systems and equipment: motive steam systems; steam attemperation systems; turbine extraction/ admission systems; feedwater heaters; turbine drain systems; turbine steam seal systems; start-up systems; condenser steam and water dumps; steam generator sources. Any connection to the turbine is a potential source of water either by induction from external equipment or by accumulation of condensed steam. The sources treated herein specifically are those found to be most frequently involved in causing damage to turbines. Although water induction into the high and intermediate pressure turbines have historically been recognized as the most damaging, experience has shown that water induction in low pressure turbines can cause significant damage.

Prevention of Water Damage to Steam Turbines Used for Electric Power Generation: Fossil-Fueled Plants

JIS B 8041:2012 燃气轮机.验收试验

Gas turbines -- Acceptance tests

ASME STP-TS-012-1-2012 燃气轮机使用的工作燃气的热物理特性

This document presents a collection of ideal gas and real gas data for 14 chemical species and air, in temperature and pressure ranges typically of interest to the gas turbine performance community. It provides recommended thermodynamic and transport property data and it explicitly presents the relatively simple equations required for calculating the ideal gas property data.

Thermophysical Properties of Working Gases Used In Working Gas Turbine Applications (STP-TS-012-1 - 2012)

ASME TDP-2-2012 发电用汽轮机水损害防护:核燃料厂

This Standard includes practices that are concerned primarily with the prevention of water damage to steam turbines used for water-cooled nuclear reactor power generation. The practices cover design, operation, inspection, testing, and maintenance of those aspects of the following power plant systems and equipment concerned with the prevention of water induction into steam turbines and the safe removal ofwater from steam turbines and the following associated systems and equipment: (a) main steam and bypass systems, piping, and drains (b) turbine extraction systems, piping, and drains (c) turbine steam seal systems, piping, and drains (d) feedwater heaters, piping, and drains (e) turbine drain systems (f) condenser steam and water dumps (g) start-up systems. This Standard is not intended to impose new requirements for existing facilities retroactively

Prevention of Water Damage to Steam Turbines Used for Electric Power Generation: Nuclear-Fueled Plants

DIN 4709:2011 测定额定热输入不超过70 kW的微型CHP设备的标准效率系数

Determination of the standard efficiency factor for micro-CHP-appliances of nominal heat input not exceeding 70 kW

ANSI/ASME PTC51-2011 燃气轮机进气口空调机

Gas Turbine Inlet Air Conditioning Equipment

ANSI/ASME B133.8-2011 燃气轮机装置噪音释放

This Standard provides methods and procedures for specifying the sound emissions of gas turbine installations for industrial, pipeline, and utility applications. This Standard is applicable to land based, or shore side barge-mounted gas turbines in single or multiple arrangements, for indoor or outdoor stationary installations. This Standard is not intended to be submitted for consideration as an ISO or ISO/IEC JTC-1 Standard.

Gas Tubine Installation Sound Emissions

ASME PTC 51-2011 燃气轮机进气口.空调设备

This Code may be used for in situ testing of inlet airconditioning systems (cooling/heating) as they apply to gas turbines in simple, cogeneration, and combinedcycle applications. Cooling systems covered by this Code include evaporative systems (foggers and media-based evaporative coolers) and mechanical/thermal refrigeration systems. Heating systems covered by this Code include compressor-bleed type systems and heating-coil systems.

Gas Turbine Inlet Air-Conditioning Equipment

ASME P-5-2010 生产用蒸汽发生器用简要数据报告

Summary Data Report For Process Steam Generators

SY/T 0440-2010 工业燃气轮机安装技术规范

本规范适用于具有风管式燃烧室和水平结合面结构的燃气轮机动力装置的安装。其他类似结构和用途的燃气轮机动力装置可参照执行。 工程施工过程中的职业健康与安全、环境保护等方面的要求应符合国家、地方法规的规定。 工业燃气轮机安装除应执行本规范的规定外，尚应符合国家现行有关标准的规定。

Installation technical specification for industrial gas turbine

NF E37-500*NF ISO 2314:2010 燃气轮机.验收试验

Gas turbines - Acceptance tests.

BS ISO 2314:2009 燃气轮机.验收试验

Gas turbines - Acceptance tests

ANSI/ISA 77.14.01-2010 矿物燃料发电池汽轮机控制装置

This standard addresses steam turbine governor controls and overspeed protection of steam turbine generators in fossil power plants. Specifically excluded from consideration are single valve and controlled extraction turbines, mechanical drive turbines, automated startup/shutdown systems, turbine supervisory instrumentation, steam bypass systems, and turbine water induction prevention (TWIP) systems.

Fossil Fuel Power Plant Steam Turbine Controls

ANSI/ASME PTC12.2-2010 蒸汽表面冷凝装置

Steam Surface Condensers

ISO 2314:2009 燃气轮机.验收试验

This International Standard applies to open-cycle gas-turbine power plants using combustion systems supplied with gaseous and/or liquid fuels as well as closed-cycle and semi-closed-cycle gas-turbine power plants. It can also be applied to gas turbines in combined cycle power plants or in connection with other heatrecovery systems. In cases of gas turbines using free-piston gas generators or special heat sources (for example synthetic gas of chemical processes, blast furnace gas), this International Standard can be used as a basis but suitable modifications are necessary. Acceptance tests of gas turbines with emission control and/or power augmentation devices that are based on fluid injection and/or inlet air treatment are also covered by this International Standard and it is necessary that they be considered in the test procedure, provided that such systems are included in the contractual scope of the supply subject to testing. Comparative testing can be subject to many different scenarios, depending on the purpose of the conducted measures. This International Standard can also be applied to comparative tests designed to verify performance differentials of the gas turbine, primarily for testing before and after modifications, upgrades or overhaul, although no special reference is made to these topics. This International Standard also includes procedures for the determination of the following performance parameters, corrected to the reference operating parameters: a) electrical or mechanical power output (gas power, if only gas is supplied); b) thermal efficiency or heat rate; c) turbine exhaust energy (optionally exhaust temperature and flow). It is necessary that any other performance parameters defined in the contract between equipment supplier and purchaser be considered accordingly in the specific test procedure as well as in the supplier's standard manufacturing test procedure. This International Standard describes measurement methods and corresponding instruments employed and their calibration arrangement and handling. It includes provisions for preparing and conducting a performance test, defines operating conditions of the gas turbine, boundary conditions and their limits as well as standard conditions (3.9) that should be used as a reference if no other conditions are agreed at the time of purchase. Furthermore, it contains provisions for the measurement data recording and handling, methods for the calculation and correction of the test results as well as the development of the uncertainty thereof. Test tolerance is not addressed in this International Standard, because it is considered a commercial term not based on statistical analysis of measurement results. It is necessary that the methodology on how to apply tolerances for the demonstration of compliance with the guaranteed values be defined in the contract. For the optional test to determine exhaust energy and/or flow, these values are determined from an energy balance around the gas turbine. Uncertainty values can be minimized by achieving the limits defined in this International Standard for the key parameters in the energy balance. 1 This International Standard does not apply to the following: a) emission testing; b) noise testing; c) vibration testing; d) performance of specific components of the gas turbine; e) performance of power augmentation devices and auxiliary systems, such as air inlet cooling devices, fuel gas compressors, etc.; f) conduct test work aiming at development and research; g) adequacy of essential protective devices; h) performance of the governing system and protective systems; i) operating characteristics (starting characteristics, reliability testing, etc.).

Gas turbines - Acceptance tests

KS B ISO 3977-4:2009 燃气轮机.采购.第4部分:燃料和环境

이 표준은 연료의 질과 환경에의 영향을 고려하여 가스 터빈을 조달하기 위한 지침을 제시한다

Gas turbines－Procurement－Part 4：Fuels and environment