L17 电感器、变压器 标准查询与下载

BS EN 60044-3:2003 仪表用变压器.组合变压器

This part of IEC 60044 applies to newly manufactured combined transformers for use with electrical measuring instruments and electrical protective devices at frequencies from 15 Hz to 100 Hz. The requirements and tests of this standard, in addition to the requirements and tests of IEC 60044-1, IEC 60044-2 and IEC/PAS 60044-5 cover current, voltage and capacitor voltage transformers, that are necessary for combined instrument transformers.

Instrument transformers - Combined transformers

NF C52-558-2-7/A11:2003 功率变压器、电源设备及类似装置的安全性.第2-7部分:玩具用变压器的特殊要求

Safety of power transformers, power supply units and similar - Part 2-7 : particular requirements for transformers for toys.

IEC 60044-2:2003 仪表用变压器.第2部分:感应电压变压器

This part of IEC 60044 applies to new inductive voltage transformers for use with electrical measuring instruments and electrical protective devices at frequencies from 15 Hz to 100 Hz. Although this standard relates basically to transformers with separate windings, it is also applicable, where appropriate, to auto-transformers. This standard does not apply to trans-formers for use in laboratories. NOTE Requirements specific to three-phase voltage transformers are not included in this standard but, so far as they are relevant, the requirements in clauses 3 to 11 apply to these transformers and a few references to them are included in those clauses (e.g. see 2.1.4, 5.1.1, 5.2, and 11.2). Clause 13 covers the requirements and tests, in addition to those in clauses 3 to 12, that are necessary for single-phase inductive protective voltage transformers. The requirements of clause 13 apply particularly to transformers which are required to have sufficient accuracy to operate protective systems at voltages that occur under fault conditions.

Instrument transformers - Part 2: Inductive voltage transformers

IEC 60044-1:2003 仪表用变压器.第1部分:电流互感器

This part of IEC 60044 applies to newly manufactured current transformers for use with electrical measuring instruments and electrical protective devices at frequencies from 15 Hz to 100 Hz. Although the requirements relate basically to transformers with separate windings, they are also applicable, where appropriate, to autotransformers. Clause 11 covers the requirements and tests, in addition to those in clauses 3 to 10, that are necessary for current transformers for use with electrical measuring instruments. Clause 12 covers the requirements and tests, in addition to those in clauses 3 to 10, that are necessary for current transformers for use with electrical protective relays, and in particular for forms of protection in which the prime requirement is the maintenance of accuracy up to several times the rated current. For certain protective systems, where the current transformer characteristics are dependant on the overall design of the protective equipment (for example high-speed balanced systems and earth-fault protection in resonant earthed networks), additional requirements are given in clause 13 for class PR transformers and in clause 14 for class PX transformers. Clause 13 covers the requirements and tests in addition to those in clauses 3 to 10 that are necessary for current transformers for use with electrical protective relays, and in particular for forms of protection in which the prime requirement is the absence of remanent flux. Clause 14 covers the requirements and tests in addition to those in clauses 3 to 10 that are necessary for current transformers for use with electrical protective relays, and in particular for forms of protection for which knowledge of the transformer's secondary excitation characteristic, secondary winding resistance, secondary burden resistance and turns ratio is sufficient to assess its performance in relation to the protective relay system with which it is to be used. Current transformers intended for both measurement and protection shall comply with all the clauses of this standard.

Instrument transformers - Part 1: Current transformers

NF C93-371:2003 高频感应部件.非电气特性和测量方法.第1部分:电子和电信设备用固定的表面安装感应器

High frequency inductive components - Non electrical characteristics and measuring methods - Part 1 : fixed, surface mounted inductors for use in electronic and telecommunication equipment.

KS C 4305-2002 发光管变压器

이 규격은 네온, 기타의 비활성 가스 또는 이들과 수은 증기를 충전한 냉음극 네온관에 전력

Luminous-tube transformers

IEC 60044-2/AMD2:2002 仪表用互感器.第2部分:电感式电压互感器.修改件3

This is Amendment 2 to IEC 60044-2-1997 (Instrument transformers Part 2: Inductive voltage transformers)

Instrument transformers - Part 2: Inductive voltage transformers; Amendment 2

IEC 60044-3:2002 仪表用互感器.第3部分:组合式互感器

This part of IEC 60044 applies to newly manufactured combined transformers for use with electrical measuring instruments and electrical protective devices at frequencies from 15 Hz to 100 Hz. The requirements and tests of this standard, in addition to th

Instrument transformers - Part 3: Combined transformers

IEC 60044-1/AMD2:2002 仪表用互感器.第1部分:电流互感器.修改件2

This is Amendment 2 to IEC 60044-1-1996 (Instrument transformers Part 1: Current transformers)

Instrument transformers - Part 1: Current transformers; Amendment 2

BS EN 62024-1:2002 高频感应部件.电气特性和测量方法.毫微亨(利)芯片感应器

This International Standard specifies electrical characteristics and measuring methods for the nanohenry range chip inductor that is normally used in high frequency (over 100 kHz) range.

High frequency inductive components - Electrical characteristics and measuring methods - Nanohenry range chip inductor

BS EN 62025-1:2002 高频感应部件.非电气特性和测量方法.电子和远程通信设备用固定表面安装的感应器

This International Standard applies to fixed, surface mounted inductors. Should conflict arise between these specifications and the detail specifications, the latter will take precedence. The object of this standard is to establish requirements to describe terms, to give recommendations for standard values and dimensions and to give guidance on fixed, surface mounted inductors.

High frequency inductive components - Non-electrical characteristics and measuring methods - Fixed, surface mounted inductors for use in electronic and telecommunication equipment

BS EN 60044-8:2002 仪表变压器.电流变压器

This part of IEC 60044 applies to newly manufactured electronic current transformers having an analogue voltage output or a digital output, for use with electrical measuring instruments and electrical protective devices at nominal frequencies from 15 Hz to 100 Hz. NOTE Additional requirements due to the bandwidth are considered. The accuracy requirements on harmonics are given in annex D. Clause 12 covers the accuracy requirements that are necessary for electronic current transformers for use with electrical measuring instruments. Clause 13 covers the accuracy requirements that are necessary for electronic current transformers for use with electrical protective relays, and particularly for forms of protection in which the prime requirement is to maintain the accuracy up to several times the rated current. If required, the transient accuracy of an electronic current transformer during fault is also given in this clause. Electronic current transformers intended for both measurement and protection should comply with all the clauses of this standard and are called multipurpose electronic current transformers. The transformer technology can be based on optical arrangements equipped with electrical components, on air-core coils (with or without a built-in integrator), or on iron-core coils with integrated shunt used as a current-to-voltage converter, alone or equipped with electronic components. For analogue output, the electronic current transformer may include the secondary signal cable. Examples of electronic current transformer technologies using air-core coils and ironcore coils with integrated shunt are given in annex C. For digital output, this standard takes into account a point-to-point connection from the electronic transformer to electrical measuring instruments and electrical devices (see annex B). Some information has been added in order to ensure the compatibility of this point-to-point link with the overall system of communication in the substation, thus allowing data exchange between all kinds of substation devices. This information builds what is called the mapping of the link layer of the point-to-point serial link. Processbus communication is under consideration. This mapping allows interoperability between devices from different manufacturers. This standard does not specify individual implementations or products, nor does it constrain the implementation of entities and interfaces within a computer system. This standard specifies the externally visible functionality of implementations together with conformance requirements for such functionalities.

Instrument transformers - Electronic current transformers

IEC 60044-8:2002 互感器.第8部分:电子电流互感器

This part of IEC 60044 applies to newly manufactured electronic current transformers having an analogue voltage output or a digital output, for use with electrical measuring instruments and electrical protective devices at nominal frequencies from 15 Hz

Instrument transformers - Part 8: Electronic current transformers

SN/T 1093-2002 进出口电流互感器检验规程

本标准规定了进出口电流互感器的抽样检验及检验结果的判定。 本标准适用于频率为 15 Hz-100 Hz，额定电压不大于 500 kV ，供电气测量仪表用和电气保护装置 用的进出口电流互感器的检验。 本标准不适用于进出口精密电流互感器的检验。

Rules for the inspection of current transformers for import and export

IEC 60688:2002 交流电量转换成模拟信号或数字信号的电测量变换器

Applies to transducers with electrical inputs and outputs for making measurements of a.c. electrical quantities with a nominal frequency between 5 Hz and 1 500 Hz. The output signal may be in the form of an analogue direct current or in digital form. Sup

Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals

IEC 62024-1:2002 高频感应部件.电气特性和测量方法.第1部分:毫微亨(利)瑕庇的感应器

This International Standard specifies electrical characteristics and measuring methods for the nanohenry range chip inductor that is normally used in high frequency (over 100 kHz) range.

High frequency inductive components - Electrical characteristics and measuring methods - Part 1: Nanohenry range chip inductor

IEC 62025-1:2002 高频感应部件.非电气特性和测量方法.第1部分:电气和远程通信设备用固定表面安装的感应器

The object of this standard is to establish requirements to describe terms, to give recommendations for standard values and dimensions and to give guidance on fixed, surface mounted inductors.

High frequency inductive components - Non-electrical characteristics and measuring methods - Part 1: Fixed, surface mounted inductors for use in electronic and telecommunication equipment

SJ/T 11255-2001 叠层型片式电感器详细规范

本规范规定了叠层片式电感器的分类、要求、试验方法、检验规则及包装、运输和贮存等要求。 本规范适用于表面安装用叠层片式电感器。

Detail specification for multiplayer chip inductors

SJ/T 11245-2001 单相R型铁心电源变压器

本标准规定了R型铁心电源变压器的技术要求、检验规则及标志、包装、运输贮存等要求。 本标准适用于工作电压不高于500 V、电源频率为1000 Hz以下、重量不大于12 kg的电子设备用干式R型铁心电源变压器。

Single-phase power transformers using R-cores

ASTM F2213-02 磁共振环境中无源插件上磁感应扭矩测量的标准试验方法

1.1 This test method covers the measurement of the magnetically induced torque produced by the static magnetic field in the magnetic resonance environment on passive implants (implants that function without the supply of electrical power) and the comparison of that torque to the equivalent torque applied by the gravitational force to the implant.1.2 This test method does not address the issue of magnetically induced force due to spatial gradients in the static magnetic field.1.3 The torque considered here is the static torque due to the interaction of the MRI static magnetic field with the magnetization in the implant. The dynamic torque due to interaction of the static field with eddy currents induced in a rotating device is not addressed in this test method.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Magnetically Induced Torque on Passive Implants in the Magnetic Resonance Environment