Q72 混凝土构配件 标准查询与下载

BS EN 494:2004 纤维水泥型板及配件.产品规范和试验方法

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses: ? roofing, ? internal wall finishes, ? external wall and ceiling finishes. For the purpose of this document fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics. This document covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating. This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets. NOTE Some of these requirements can be applied to curved sheets, after agreement between manufacturer and purchaser.

Fibre-cement profiled sheets and fittings — Product specification and test methods

DIN EN 12843:2004 预制混凝土产品.杆和柱

This standard applies to precast concrete poles and pole elements, reinforced and/or prestressed; they may receive or include additional components (e. g. cross-arms, platforms etc.) inserts and connections.

Precast concrete products - Masts and poles; German version EN 12843:2004

JC/T 934-2004 预制钢筋混凝土方桩

Precast reinforced concrete square piles

SANS 10109-2:2004 混凝土地面．第二部分：混凝土地面终饰

Covers general principles for commonly used floor finishes of certain types.

Concrete floors Part 2: Finishes to concrete floors

NF P18-948*NF EN 13295:2004 混凝土结构的保护和修理用产品和系统.试验方法.耐碳化作用的测定

Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation.

ISO 8336:1993/Amd 1:2004 纤维水泥平板.修改件1

Fibre-cement flat sheets; Amendment 1

ISO 9933:1995/Amd 1:2004 纤维增强水泥制品.屋面和覆盖用大波瓦或非对称截面瓦和配件.修改件1

This is Amendment 1 to ISO 9933-1995 (Products in fibre-reinforced cement — Long corrugated or asymmetrical section sheets and fittings for roofing and cladding —AMENDMENT 1 )

Products in fibre-reinforced cement - Long corrugated or asymmetrical section sheets and fittings for roofing and cladding; Amendment 1

JIS A 5362:2004 预制混凝土产品.要求的性能和验证方法

この規格は，プレキャストコンクリート製品(以下,製品という。)の要求性能及び照査方法に関する一般的事項について規定する。ただし，建築用コンクリート製品には適用しない。備考この規格は本来，製品の性能についてだけ規定すべきものであるが，製品の使用状況の特性上，製品を使った構造物の性能と全く分離して議論するのが難しい。そこで，製品を用いた構造物の性能にも言及している。しかし，製品と構造物との関係も，製品がそのまま構造物となるもの，製品が構造物の一部をなすもの，製品を複数組み合わせて構造物とするものなど，多様であるため，必ずしも構造物の性能を分離しなくてもよいものもある。また，構造物の設計を考えた場合，構造物への要求性能を基に構造物が計され，それを基に構造物の一部をなす製品が設計?製造されるという流れとなるであろう。この場合には，購人者が構造物及び製品の要求性能を提示し，それを基に製品の製造者が構造物及び製品の設計?照査を行った上で製品の製造を行うことになる。しかし，一般的には製造者は構造物及び製品が使用される状況をある程度想定して製品を設計し，製品の性能を推奨仕様，団体規格などで提示した上で販売することが多いと思われる。この場合，購入者は複数種類の製品から，構造物の性能を満足するような製品を選定して用いることとなると考えられる。

Precast concrete products -- Required performance and methods of verification

JIS A 5371:2004 预制非增强混凝土产品

この規格は，無筋コンクリート製()のプレキャストコンクリート製品（以下,URC製品という。)について規定する。ただし，建築用コンクリート製品及び視覚障害者誘導用コンクりート製品には適用しない。 注()鉄筋コンクリート構造とすることを意図せず，施工上の安全確保などを目的として，鋼材などを使用している製品については，URC製品とする。

Precast unreinforced concrete products

JIS A 5373:2004 预制预应力混凝土制品

この規格は，プレストレストコンクリート製のプレキャストコンクリート製品(以下,PC製品という。)について規定する。ただし，建築用コンクリート製品には適用しない。

Precast prestressed concrete products

JIS A 5361:2004 预制混凝土产品.分级、名称与符号及标记的一般规则

この規格は，プレキャストコンクリート製品(以下,製品という。)の種類，製品の呼び方及び表示に関する一般的事項について規定する。ただし，建築用コンクリート製品には適用しない。

Precast concrete products -- General rules for classification, designation and marking

JIS A 5372:2004 预制增强混凝土产品

この規格は，鉄筋コンクリート製()のプレキャストコンクリート製品(以下,RC製品という。)について規定する。ただし，個別の製品について，日本工業規格が別途定められている建築用コンクリート製品及び視覚障害者誘導用コンクリート製品の場合には，この規格は適用しない。 注()鉄筋コンクリート構造とすることを意図せず，施工上の安全確保などを目的として.鋼材などを使用している製品については，無筋コンクリート製品とする。

Precast reinforced concrete products

JIS A 5363:2004 预制混凝土产品.性能试验方法的一般规则

この規格は，プレキャストコンクリート製品(以下,製品という。)の性能を照査する方法のうち，性能試験による場合の一般的事項について規定する。また，この規定は，他の適切な試験方法を制限するものではなく，製品の型式検査(性能試験の区分)，最終検査及び受渡検査における試験に適宜適用するものとする。ただし，建築用コンクリート製品には適用しない。

Precast concrete products -- General rules for methods of performance test

JIS A 5364:2004 预制混凝土产品.材料和生产方法的一般规则

この規格は，プレキャストコンクリート製品(以下,製品という。)の材料及び製造方法の一般的事項について規定する。ただし，建築用コンクリート製品には適用しない。

Precast concrete products -- General rules of materials and product methods

JIS A 5365:2004 预制混凝土产品.检验方法的一般规则

この規格は，プレキャストコンクリート製品（以下,製品という。)について，製造された製品の検査方法の一般的事項について規定する。ただし，建築用コンクリート製品には適用しない。 備考この規格では，“型式検査”については触れない。型式検査は，製品の場合，要求された性能を満たすように設計，又は仕様を決定し，それを照査した後に確認する行為であり，繰返しの製造に入る前に行う行為である。この規格では，繰返しの製造に入った後の，製造された製品の検査を対象とする。

Precast concrete products -- General rules for method of inspection

ASTM E2394-04 安装的石棉水泥产品的维护、修补和维修的标准规程

1.1 This standard practice describes work practices for asbestos-cement products when maintenance, renovation and repair are required. This includes common tasks such as drilling and cutting holes in roofing, siding, pipes, etc. that can result in exposure to asbestos fibers if not done carefully. 1.2 Materials covered include those installed in or on buildings and facilities, and those used in external infrastructure such as water, wastewater and electrical distribution systems. Also included is pavement made from asbestos-cement manufacturing waste.1.3 The work practices described herein are intended for use only with asbestos-cement products already installed in buildings, facilities and external infrastructure. They are not intended for use in construction or renovation involving the installation of new asbestos-cement products.1.4 The work practices described herein are not intended for use where the primary objective is the removal of asbestos-cement products from the building or other location. The work practices are intended to be used in situations where small amounts of asbestos-cement products must be removed or disturbed in order to perform maintenance, renovation or repair necessary for operation of the building, facility or infrastructure.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This standard practice does not address safety hazards associated with working on asbestos-cement products such as falling through roof panels or trench cave-ins. The use of power tools presents possible electrical hazards, particularly in wet environments. These and other safety hazards must be considered and controlled in compliance with the employer''s policies and applicable regulations.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Maintenance, Renovation and Repair of Installed Asbestos Cement Products

ASTM C1504M-04e1 涵洞和雨水管用预制钢筋混凝土三边结构制造的标准规范(米制)

1.1 This specification covers single-cell precast conventionally reinforced concrete three-sided structures intended to be used for the construction of culverts and for the conveyance of storm water and sewage.1.2 This specification is the metric counterpart of Specification C 1504; therefore, no imperial equivalents are presented in this specification.Note 18212;This specification is primarily a manufacturing and purchasing specification. The successful performance of this product depends upon the proper selection of the geometric section, bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete three-sided structure specified herein is cautioned that he must properly correlate the loading conditions and the field requirements with the geometric section specified and provide for inspection at the construction site.

Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts, Storm Drains (Metric)

ASTM C1504-04 涵洞和雨水管用预制钢筋混凝土三边结构制造的标准规范

1.1 This specification covers single-cell precast conventionally reinforced concrete three-sided structures intended to be used for the construction of culverts and for the conveyance of storm water.1.2 A complete metric companion to Specification C 1504 has been developed-C 1504M; therefore, no metric equivalents are presented in this specification.Note 18212;This specification is primarily a manufacturing and purchasing specification. The successful performance of this product depends upon the proper selection of the geometric section, bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete three-sided structure specified herein is cautioned that he must properly correlate the loading conditions and the field requirements with the geometric section specified and provide for inspection at the construction site.

Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts, Storm Drains

ASTM C1504-04e1 涵洞和雨水管用预制钢筋混凝土三边结构制造的标准规范

1.1 This specification covers single-cell precast conventionally reinforced concrete three-sided structures intended to be used for the construction of culverts and for the conveyance of storm water.1.2 A complete metric companion to Specification C 1504 has been developed-C 1504M; therefore, no metric equivalents are presented in this specification.Note 18212;This specification is primarily a manufacturing and purchasing specification. The successful performance of this product depends upon the proper selection of the geometric section, bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete three-sided structure specified herein is cautioned that he must properly correlate the loading conditions and the field requirements with the geometric section specified and provide for inspection at the construction site.

Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts, Storm Drains

ASTM C956-04 现场浇注的增强石膏混凝土构件安装的标准规范

1.1 This specification covers the minimum requirements for the installation of cast-in-place reinforced gypsum concrete over permanent formboard. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes shall not be considered requirements of the standard.

Standard Specification for Installation of Cast-In-Place Reinforced Gypsum Concrete