Q72 混凝土构配件 标准查询与下载

JIS A 5371 ERRATUM 2:2005 勘误

ERRATUM

JIS A 5364 ERRATUM 2:2005 勘误

ERRATUM

JIS A 5362 ERRATUM 1:2005 勘误

ERRATUM

JIS A 5365 ERRATUM 2:2005 勘误

ERRATUM

NF P18-977-2*NF EN 12617-2:2005 混凝土构件的保护和维修用产品和系统.试验方法.第2部分:基于高聚物粘合剂的裂缝注入产品的收缩率:体积收缩

Products and systems for the protection and repair of concrete structures - Test methods - Part 2 : shrinkage of crack injection product based on polymer binder : volumetric shrinkage.

NF P18-982*NF EN 14498:2005 混凝土结构的保护和维修用产品和系统.试验方法.空气干燥与储水循环后注入产品的体积和重量的变化

Products and systems for the protection and repair of concrete structures - Test methods - Volume and weight changes of injection products after air drying and water storage cycles.

ASTM E2265-05 混凝土和砖石工程用锚和紧固件的标准术语

1.1 This document provides standard terminology for anchors and fasteners installed in structural members made of concrete or masonry.1.2 This terminology does not cover terms relating to the mechanical properties of the materials used for fabricating anchors, nor does it cover their use.1.3 The terms are listed alphabetically. Compound terms appear in the natural spoken order.

Standard Terminology for Anchors and Fasteners in Concrete and Masonry

ASTM D4261-05 混凝土预制件涂覆前表面清洁处理的标准实施规范

Surface cleaning is to be used to prepare concrete unit masonry surfaces for applying coatings intended for light duty service, splash and spillage of water and chemical solutions, radiation exposure, decontamination, and repeated washdowns with alkaline cleaners.1.1 This practice covers surface cleaning of concrete unit masonry to remove dust, dirt, mortar spatter, oil, and grease prior to the application of coatings. Procedures include vacuum cleaning, air-blast cleaning, water cleaning, detergent water wash, steam cleaning, and mechanical cleaning. 1.2 This practice is not intended to alter the surface profile of the concrete masonry units but to clean the surface. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.

Standard Practice for Surface Cleaning Concrete Masonry Units for Coating

ASTM D4258-05 覆层用表面清洁混凝土的标准规程

Surface cleaning is used to prepare concrete surfaces for applying coatings intended for light-duty service. Use of this practice alone is not intended where protective systems will be used for continuous or intermittent immersion, mechanical loading, or for protective systems needing optimum bond for satisfactory performance (see Practices D 4259 and D 4260).1.1 This practice includes surface cleaning of concrete to remove grease, dirt, and loose material prior to the application of coatings. Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning, detergent water cleaning, and steam cleaning. 1.2 This practice is not intended to alter the surface profile of the concrete but to clean the surface. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see Section 5.

Standard Practice for Surface Cleaning Concrete for Coating

ASTM E2265-05a 混凝土和砖石工程用锚和紧固件的标准术语

1.1 This document covers standard terminology for anchors and fasteners installed in structural members made of concrete or masonry.1.2 This terminology does not cover terms relating to the mechanical properties of the materials used for fabricating anchors, nor does it cover their use.1.3 The terms are listed alphabetically. Compound terms appear in the natural spoken order.

Standard Terminology for Anchors and Fasteners in Concrete and Masonry

ASTM C1262-05a 制造混凝土砌块和相关混凝土构件的冷融耐久性评价的标准试验方法

1.1 This test method covers the resistance to freezing and thawing manufactured concrete masonry and related concrete units. Units are tested in a test solution that is either water or 3 % saline solution depending on the intended use of the units in actual service. Note 138212;Concrete masonry and related concrete units include units such as hollow and solid concrete masonry units, concrete brick, segmental retaining wall units, concrete pavers, and concrete roof pavers.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating the Freeze-Thaw Durability of Manufactured Concrete Masonry Units and Related Concrete Units

ASTM C1262-05 制造混凝土砌块和相关混凝土构件的冷融耐久性评价的标准试验方法

1.1 This test method covers the resistance to freezing and thawing manufactured concrete masonry and related concrete units. Units are tested either in water or in a saline solution depending on the intended use of the units in actual service. Note 18212;Concrete masonry and related concrete units include units such as hollow and solid concrete masonry units, concrete brick, segmental retaining wall units, concrete pavers, and concrete roof pavers.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating the Freeze-Thaw Durability of Manufactured Concrete Masonry Units and Related Concrete Units

BS EN 13225:2004 预浇铸混凝土产品.线性结构部件

This document identifies the requirements, the basic performance criteria and evaluation of conformity for precast linear elements (such as columns, beams and frame elements) made of reinforced or prestressed normal weight concrete, used for the construction of the structures of buildings and other civil engineering works, except bridges. This document covers terminology, performance criteria, tolerances, relevant physical properties, test methods, and aspects of transport and erection. This document does not cover load bearing capacity determined by testing.

Precast concrete products. Linear structural elements

BS EN 13224:2004 预制混凝土制品.有筋楼板元件

This document identifies the requirements, the basic performance criteria and evaluation of conformity for precast ribbed elements made of reinforced or prestressed normal weight concrete, used in floors or roofs. The elements consist of a top slab and one or more (usually two) ribs, containing the main longitudinal reinforcement; a bottom slab and transverse ribs may also be present. Some examples of precast elements considered in this document are shown in the Informative Annex A. This document covers terminology, performance criteria, tolerances, relevant physical properties, test methods and aspects of transport and erection. This document does not cover load bearing capacity determined by testing.

Precast concrete products — Ribbed floor elements

BS EN 12843:2004 预制混凝土制品.电线杆

This document specifies requirements for precast concrete poles (also commonly called masts) (either all of a piece or composed of elements), reinforced and/or prestressed as structural elements; they may be hollow or solid and may receive or include additional components (e.g. cross-arms, platforms etc.), inserts and connectors. Additional elements may be connected to pole elements. Structures made from such elements in mono- or multi-legged form may be used for : — overhead electrical lines ; — telecommunication lines ; — overhead electrical lines for railways, trams and similar ; — supports for lighting ; — supports for loudspeaker installation ; — antenna and telecommunication poles ; — supports for wind turbines ; — and similar installations. This document does not cover lighting columns for use in traffic circulation areas.

Precast concrete products - Masts and poles

BS EN 492:2004 纤维水泥条板及配件.产品规格和试验方法

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses: - roofing, - internal wall finishes, - external wall and ceiling finishes. It applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this standard, fibre-cement slates have been classified according to their bending moment. This document covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1. This standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

Fibre cement slates and fittings - Product specification and test methods

BS EN 12467:2004 纤维水泥平板材.产品规范和试验方法

This document specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses: — internal wall and ceiling finishes, — external wall and ceiling finishes. Products covered by this document can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays. NOTE prEN (Wl 128087) "Roof covering products for discontinuous laying and products for wall cladding - Rigid underlays - Rigid underlays for discontinuously laid roof coverings - Product specification and test methods" is under preparation. This document covers sheets reinforced with fibres of different types as specified in 5.1.1. This document does not cover sheets for fire protection purposes. This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

Fibre-cement flat sheets - Product specification and test methods

ANSI/AWWA D110-2004 线绕式环形预应力混凝土水箱

The intent of this standard is to describe current recommended practice for the design, construction, inspection, and maintenance of wire- and strand-wound, circular, prestressed concrete water-containing structures with the following four types of core walls: type I - cast-in-place concrete with vertical prestressed reinforcement; type II - shotcrete with a steel diaphragm; type III - precast concrete with a steel diaphragm; type IV - cast-in-place concrete with a steel diaphragm.

Wire-Wound, Circular Prestressed Concrete Water Tanks

BS EN 13693:2004 预浇铸混凝土制品.特殊屋顶部件

This document identifies the requirements, the basic performance criteria and the evaluation of conformity for special precast roof elements made of reinforced or prestressed normal weight concrete, used for the construction of buildings, with or without separating function with respect to fire resistance. NOTE The title of special roof elements refers to thin-walled structural elements with deformable transverse profile, such as folded plates, or shell elements, the intended use being specific for roofings with their typical loads. This type of elements combines the overall flexural behaviour along the main span with a complex distribution of in-plane forces and local moments. Other types of elements can be used in roofing, such as ribbed units, floor slabs, ... . For these elements reference shall be made to their respective product standards. Secondary structural components, possibly used in combination with the main roof elements, such as load bearing shuttering plates and shells, roof light frames, ..., shall refer to their respective product standard or technical approval. This document covers terminology, performance criteria, tolerances, relevant physical properties, test methods, and aspects of transport and erection. This document does not deal with seismic behaviour. This document does not cover load bearing capacity determined by testing.

Precast concrete products - Special roof elements

BS EN 13693:2004+A1:2009 预浇铸混凝土制品.屋顶专用部件

This document identifies the requirements, the basic performance criteria and the evaluation of conformity for special precast roof elements made of reinforced or prestressed normal weight concrete, used for the construction of buildings, with or without separating function with respect to fire resistance. Other types of elements can be used in roofing, such as ribbed units, floor slabs, ... . For these elements reference shall be made to their respective product standards. !This document identifies also the requirements, the basic performance criteria and the evaluation of conformity of complementary elements made of reinforced or prestressed normal weight concrete, possibly used in combination with the main roof elements, such as load bearing shuttering plates and shells, for which reference shall be made to Annex F." This document covers terminology, performance criteria, tolerances, relevant physical properties, test methods, and aspects of transport and erection. This document does not deal with seismic behaviour. This document does not cover load bearing capacity determined by testing.

Precast concrete products - Special roof elements