Q74 塑料构配件 标准查询与下载

ASTM F1913-04 无背衬的乙烯基薄板地板覆盖物的标准规范

1.1 This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layer(s). 1.2 This type of floor covering is intended for use in commercial and light commercial buildings. General information and performance characteristics, which determine service-ability and recommended use, are included in this specification. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Vinyl Sheet Floor Covering Without Backing

BS 7412:2002 未增塑的聚氯乙烯(PVC-U)挤制空心型材制的塑料窗.规范

This British Standard specifies requirements for the materials, including glass and glazing, construction, security, safety, weathertightness, and operation and strength performance of new windows made from PVC-U extruded hollow profiles conforming to BS 7413, up to the point of installation of the windows provided the windows have been handled and stored in accordance with the manufacturer's instructions. This British Standard applies to windows manufactured from PVC-U hollow profiles incorporating fusion welded corner joints. It applies to the following window types, in multi-light or composite form: a) hinged: side hung (open in or out), top hung (open out), bottom hung (open in), tilt and turn or turn before tilt; b) projecting: side hung (open in or open out) and top hung (open out or reversible); c) pivoted: horizontal and vertical (hung centrally or off-centre) including reversible; d) sliding: horizontal and vertical; e) side hung: fully reversible; f) fixed light. It is applicable to windows in which any frame member is not longer than 3 m. It does not apply to curtain walls that span across horizontal structural members of floors but is applicable to windows within a curtain walling system.

Plastics windows made from unplasticized polyvinyl chloride (PVC-U) extruded hollow profiles - Specification

ASTM F1913-02 无背衬的乙烯基薄楼板覆层的标准规范

1.1 This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layer(s). 1.2 This type of floor covering is intended for use in commercial and light commercial buildings. General information and performance characteristics, which determine service-ability and recommended use, are included in this specification. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Vinyl Sheet Floor Covering Without Backing

JIS A 5390:2001 预制混凝土的塑料隔板

この規格は，工場で製造され，る鉄筋コンクリート製品の鉄筋の位置を固定するために用いるプラスチックスペーサ(以下,スペーサという。）について規定する。

Plastics spacers for precast concrete

DIN 16830-3:2000 门窗用高耐冲击聚氯乙烯(PVC-HI)型材.第3部分:表面着色的型材.要求

High impact polyvinyl chloride (PVC-HI) profiles for windows and doors - Part 3: Profiles with coloured surfaces; Requirements

DIN 16830-4:2000 门窗用高耐冲击聚氯乙烯(PVC-HI)型材.第4部分:表面着色的型材.试验方法

The document specifies test methods for high impact polyvinyl chloride (PVC-HI) profiles for windows with coloured surfaces.

High impact polyvinyl chloride (PVC-HI) profiles for windows and doors - Part 4: Profiles with coloured surfaces; Test method

JG/T 124-2000 聚氯乙烯(PVC)门窗执手

本标准规定了聚氯乙烯（PVC）门窗执手的定义、产品分类及型号、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于聚氯乙烯（PVC）门窗用执手。

Handle of rigid polyvinyl chloride window and door

JG/T 132-2000 聚氯乙烯(PVC)门窗固定片

本标准规定了聚氯乙烯（PVC）门窗固定片的定义、产品型号、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于聚氯乙烯（PVC）门窗用固定片。

Wedges or fixings of rigid polyvinyl chloride window and door

JG/T 130-2000 聚氯乙烯(PVC)门窗半圆锁

本标准规定了聚氯乙烯（PVC）门窗半圆锁的定义、产品型号、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于推拉式聚氯乙烯（PVC）门窗室内用锁。

Camlock of rigid polyvinyl chloride window and door

JG/T 129-2000 聚氯乙烯(PVC)门窗滑轮

本标准规定了聚氯乙烯(PVC）门窗滑轮的定义、型号、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于在聚氯乙烯(PVC）推拉门窗上的各种滑轮。

Roller of rigid polyvinyl chloride window and door

JG/T 128-2000 聚氯乙烯(PVC)门窗撑挡

本标准规定了聚氯乙烯(PVC）门窗撑挡的定义、产品分类和型号、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于平开聚氯乙烯（PVC）窗定位用撑挡。

Stay of rigid polyvinyl chloride window and door

JG/T 127-2000 聚氯乙烯(PVC)门窗滑撑

本标准规定了聚氯乙烯（PVC）门窗滑撑的定义、型号、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于聚氯乙烯（PVC）门窗中的上悬窗、下悬窗和平开窗。

Sliding pivots of rigid polyvinyl chloride window and door

JG/T 126-2000 聚氯乙烯(PVC)门窗传动锁闭器

` 本标准规定了聚氯乙烯（PVC）门窗传动锁闭器的定义、产品分类及型号、要求、试验方法、检验规则和标志、包装、运输及贮存。 本标准适用于聚氯乙烯(PVC）门窗用传动锁闭器。

Driving gear of rigid polyvinyl chloride window and door

JG/T 125-2000 聚氯乙烯(PVC)门窗合页(铰连)

本标准规定了聚氯乙烯(PVC）门窗合页（铰链）的产品分类和型号、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于聚氯乙烯(PVC）门窗用合页（铰链）。

Hinge of rigid polyvinyl chloride window and door

DIN EN 514:2000 门窗构架未增塑聚氯乙烯(PVC-U)型材.焊接角和T型连接强度测定.

The document specifies two test methods for the measurement of the failure load of welded corners and T-joints made from unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors. From the failure load the failure stress is calculated..

Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the strength of welded corner and T-joint; German version EN 514:2000

JG/T 116-1999 聚碳酸脂(PC)中空板

本标准规定了聚碳酸酯(PC）中空板的分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于以聚碳酸酯(PC）树脂为主要原料，填加各种助剂，经挤出成型的聚碳酸酯(PC）中空板。

Multiwall polycarbonate sheets

ASTM D4226-00 刚性聚氯乙烯建筑制品耐冲击性的标准试验方法

1.1 These test methods cover the determination of the energy required to crack or break rigid poly(vinyl chloride) (PVC) plastic sheeting and profile flat sections used in building products, as well as extruded or molded test samples, under specified conditions of impact from a freefalling standard weight striking an impactor with either of two configurations in contact with the specimen.1.2 Two test procedures are included:1.2.1 Procedure A used to determine minimum impact energy required to cause failure (hole, crack, split, shatter, or tear).1.2.2 Procedure B used to determine minimum impact energy required to cause brittle failure.1.3 The values in inch-pound units are to be regarded as the standard.Note 1--There is no similar or equivalent ISO standard.1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding, those in tables in figures) shall not be considered as requirements of this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.

Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products

ASTM C1486-00(2008) 检验耐化学物质和泥浆扩散的树脂整体地板表面的标准实施规程

Because the sample is prepared in a manner as it would be applied in the field, the test specimens may be considered representative of the application of a specified surfacing. Such methods include application by squeegees, rollers, trowels, notched trowels, and gage rakes. These systems vary in several ways, including the number of layers or application steps, the surface finish, and variation in composition. The results obtained in carrying out this practice should serve as a guide in comparing similarly applied surfacings. No attempt has been made to incorporate into this practice all of the various factors that may affect the performance of such applications when subjected to actual service.1.1 This practice covers methods for preparing test specimens and testing procedures for broadcast or slurry-broadcast monolithic floor surfacings in areas where chemical resistance is required. 1.2 These floor surfacings are applied by various application methods including squeegees, rollers, trowels, notched trowels, and gage rakes onto suitably prepared concrete substrates. The surfacings bond to the substrate upon curing to provide a nominal thickness of 60 mils (1.5 mm) or greater. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings

DIN EN 1566-1:1999 建筑结构中污物和废水排放(低温和高温)用塑料管道系统.氯化聚氯乙烯(PVC-C).第1部分:管道、管件和系统规范

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system; German version EN 1566-1:1998

DIN EN 1329-1:1999 建筑物污物和污水排放(低温和高温)用塑料管道系统.未增塑聚氯乙烯(PVC-U).第1部分:管道、配件和系统规范; 德文版本 EN 1329-1:1999

The document specifes the requirements for pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) pipings systems in the field of soil and waste discharge (low and high temperature) inside buildings and for soil and waste discharge systems for both inside buildings and buried in ground within the building structure.#,,#

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system; German version EN 1329-1:1999