Q74 塑料构配件 标准查询与下载

BS 8204-6:2008+A1:2010 整平板,底基和现场铺设用地板材料.合成树脂地板材料.实施规程

This part of BS 8204 gives recommendations for the design and installation of in situ synthetic resin flooring, based on liquid synthetic resin binders in which curing takes place by chemical reaction of the resin components, used internally in buildings. The synthetic resin floorings are bonded to direct finished concrete slabs, polymer-modified cementitious or fine concrete screeds and to existing concrete floors. Annex A gives recommendations for the design and installation of resin terrazzo flooring. Synthetic resin floorings applied to other materials such as timber or metal are not covered by this code of practice. The installation of resilient sports surfacings based on synthetic resins is not covered by this code of practice.

Screeds, bases and in situ floorings. Synthetic resin floorings. Code of practice

DIN EN 15468:2008 叠层地板覆盖物.直接应用于印刷和树脂表面层的元素.规范、要求和试验方法

This European Standard specifies characteristics, states requirements and references test methods for laminate floor coverings with a directly applied printing and resin surface layer. It includes a classification system, based on EN 685, providing practical requirements for areas of use and levels of use, to indicate where laminate floor coverings will give satisfactory service and to encourage the consumer to make an informed choice. It also specifies requirements for marking and packaging. Laminate floor coverings are considered for domestic and commercial levels of use. This standard does not specify requirements relating to areas that are subject to frequent wetting, such as bathrooms, laundry rooms or saunas, but it does apply to domestic kitchens.

Laminate floor coverings - Elements with directly applied printing and resin surface layer - Specifications, requirements and test methods; English version of DIN EN 15468:2008-01

CAS 142-2007 建筑玻璃窗膜技术规范

本标准规定了建筑玻璃窗膜的技术要求和试验方法、建筑玻璃贴膜工艺技术条件、质量要求，标志、包装和贮存。 本标准适用于建筑玻璃窗内侧贴膜，也适用于建筑玻璃贴膜工艺和质量要求。

Technical Criterions for Building Window Film

DIN 24537-3:2007 用作地板覆盖物的格板.第3部分:塑料格板

Gratings used as floor coverings - Part 3: Plastic gratings

SANS 786:2007 软质聚乙烯地板

Specifies the characterisics of smooth-surfaced flexible vinyl flooring, in tile or sheeting form. The flooring may be marbled or mottled throughout its thickness.

Flexible vinyl flooring

SANS 1553-1:2007 室外用PVC-U窗框和门框．第1部分：窗框和门框用PVC-U型材

Specifies requirements for the material, basic properties, and design of extruded profiles produced from unplasticized poly(vinyl chloride) (PVC-U) for the construction of window and door frames for external use.

PVC-U window and door frames for external use Part 1: PVC-U profiles for window and door frames

BS 7412:2007 未增塑聚氯乙烯(PVC-U)挤制空心型窗和门具规范

This British Standard specifies requirements for the design, fabrication and performance of windows and glazed doorsets made from PVC-U extruded hollow profiles. This British Standard applies to windows and doorsets manufactured from PVC-U hollow profiles incorporating fusion welded corner joints. It applies to windows and doors fabricated into frames in a factory, to be installed vertically (within 15°) into the external face of buildings, as single or multi-light units, in coupled assemblies when appropriate, of the following types: a) windows: 1) hinged: side-hung (open in or out), top-hung (open out), bottom-hung (open in), tilt and turn or turn before tilt; 2) projecting: side-hung (open in or open out) and top-hung (open out or reversible); 3) pivoted: horizontal and vertical (hung centrally or off-centre) including reversible; 4) sliding: horizontal and vertical; 5) side-hung: fully reversible; 6) fixed light; b) doors: 1) single leaf single-swing doors with or without side lights and top panels; 2) double leaf single-swing doors with or without side lights and top panels. It is applicable to assemblies in which any frame member is not longer than 3 m. It does not apply to curtain walls that span across horizontal structural members of floors but is applicable to windows within a curtain walling system. It is applicable to assemblies up to the point of installation. NOTE Guidance on the evaluation of conformity is given in Annex A. Guidance on durability and recycling is given in Annex B.

Specification for windows and doorsets made from unplasticized polyvinyl chloride (PVC-U) extruded hollow profiles

NF P62-203:2007 建筑工程.聚氯乙烯(PVC)地板覆盖物.第1-1部分:技术规范.第1-2部分:选用材料的一般标准.第2部分:特殊条款的合同单据

Building works - PVC foor coverings - Part 1-1 : technical specifications - Part 1-2 : general criteria for selection materials - Part 2 : contract bill of special clauses.

NF P62-203-1-1:2007 建筑工程.聚氯乙烯(PVC)地板覆盖物.第1-1部分:技术规范

Building works - PVC floor coverings - Part 1-1 : technical specifications.

NF P62-203-2:2007 建筑工程.聚氯乙烯(PVC)地板覆盖物.第2部分:特殊条款的合同单据

Building works - PVC floor coverings - Part 2 : contract bill of special clauses.

NF P62-203-1-2:2007 建筑工程.聚氯乙烯(PVC)地板覆盖物.第1-2部分:选用材料的一般标准

Building works - PVC floor coverings - Part 1-2 : general criteria for selection materials.

ASTM D6662-07 聚烯烃基塑料木装饰板的标准规范

1.1 This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards.1.2 Plastic lumber products are currently made predominantly with recycled polyolefin plastics (in particular high-density polyethylene) where the products are more or less non-homogenous in the cross-section. However, this specification is also potentially applicable to similar manufactured plastic products made from other plastic and plastic composite materials that have non-homogenous cross-sections.1.3 This specification details a procedure to calculate recommended span lengths for spacing of support joists. This procedure was developed using experimental data from a typical unreinforced plastic lumber made predominantly from recycled high-density polyethylene. The methodology to develop span lengths for other types and compositions of plastic lumber is detailed in Appendix X1 of this standard.1.4 The values are stated in inch-pound units, as these are currently the most common units used by the construction industry. Equivalent SI units are indicated in parentheses. However, the units stated for irradiance exposure in the weatherability section (6.3) are in SI units as these are the units commonly used for testing of this type.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1There is no similar or equivalent ISO Standard.

Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

ASTM D6947-07(2013) 喷涂聚氨酯泡沫屋顶系统用液体水分固化聚氨酯涂层的标准规范

1.1 This specification covers a single component, moisture cured, elastomeric urethane polymer coating used as a protective coating for spray polyurethane foam roofing systems. 1.2 This specification does not provide guidance for application. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 The following precautionary caveat pertains only to the test method portions, Sections 5 and 6. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

ASTM D6947/D6947M-07(2013)e1 喷涂聚氨酯泡沫屋顶系统用液体水分固化聚氨酯涂层的标准规范

1.1 This specification covers a single component, moisture cured, elastomeric urethane polymer coating used as a protective coating for spray polyurethane foam roofing systems. 1.2 This specification does not provide guidance for application. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following precautionary caveat pertains only to the test method portions, Sections 5 and 6. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

SANS 1042:2006 聚合物地板敷料

covers two types of a slip-resistance; waterbased polymer floor dressing that is suitable for use on thermoplastic (asphalt), semiflexible vinyl (vinyl-asbestos), flexible vinyl, linoleum, rubber, and sealed flooring.

Polymer floor dressings

JG/T 180-2005 未增塑聚氯乙烯(PVC-U)塑料门

本标准规定了未增塑聚氯乙烯(PVC-U)塑料门(以下简称塑料门)的术语和定义、分类、规格和型号、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于由未增塑聚氯乙烯(PVC-U)型材制作的建筑用门。不适用于本标准中未规定性能的其他门。

Unplasticized polyvinyl chloride (PVC-U) doors

JG/T 176-2005 塑料门窗及型材功能结构尺寸

本标准规定了塑料门窗及型材功能结构尺寸的术语和定义及要求。 本标准适用于未增塑聚氯乙烯(PVC-U)型材断面功能部位尺寸的设计。

Function structure measurement of plastic window/door and profile

JG/T 140-2005 未增塑聚氯乙烯(PVC-U)塑料窗

本标准规定了未增塑聚氯乙烯(PVC-U)塑料窗(以下简称塑料窗)的术语和定义、分类、规格和型号、材料、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于由未增塑聚氯乙烯(PVC-U)型材制作的建筑用窗。不适用于本标准中未规定性能的其他窗。

Unplasticized polyvinyl chloride (PVC-U) windows

ASTM D4226-05 硬质聚氯乙烯(PVC)建筑产品耐冲击性的标准试验方法

The impact strength values obtained on the flat sections of a building product profile are relevant only to the flat section that has been tested and these values do not necessarily indicate the impact resistance of the whole product, which is affected by the configuration of the profile (that is, corners, ribs, etc). Constant weight and variable height, employed in these test methods, allow the velocity of impact to vary and, therefore, by Procedure B, can determine the energy of ductile-to-brittle transition, which cannot be determined if a variable weight is dropped from a constant height. These test procedures have been found to be useful elements in rigid poly(vinyl chloride) (PVC) building product characterization. Compound qualification, finished product quality control, environmental and weatherability research and development studies, and fabrication tolerance prediction constitute useful applications. Choice of the specific impactor head configuration used is related to a variety of product attributes, such as specimen thickness and product toughness as well as abstract factors, such as the anticipated mode of failure in a specific application. The geometric uniqueness of the impactor head configurations prevents any comparison or correlation of testing results on samples tested with differing impactor head configurations. In general, the conical impactor, C.125, is useful to ensure failure of thicker specimens where the H.25 impactor caused no failure. Note 28212;Equivalent surface conditions are more likely to occur when specimens are prepared by compression molding or extrusion than by injection molding. When comparing different samples tested with the same impactor head configuration, impact resistance shall be permitted to be normalized for average specimen thickness over a reasonably broad range (for example, 1 to 3 mm).3 However, this should only be done when the surface conditions listed in 6.1 are essentially equivalent. FIG. 2 Impact Tester1.1 These test methods cover the determination of the energy required to crack or break rigid poly(vinyl chloride) (PVC) plastic sheeting and profile flat sections used in building products, as well as extruded or molded test samples, under specified conditions of impact from a freefalling standard weight striking an impactor with either of two configurations in contact with the specimen.1.2 Two test procedures are included:1.2.1 Procedure A, used to determine minimum impact energy required to cause failure (hole, crack, split, shatter, or tear).1.2.2 Procedure B, used to determine minimum impact energy required to cause brittle failure.1.3 The values in inch-pound units are to be regarded as the standard.Note 18212;There is no similar or equivalent ISO standard.1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding, those in tables in figures) shall not be considered as requirements of this standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.

Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products

ASTM F1913-04(2010) 无衬垫薄乙烯树脂地面铺层的标准规范

1.1 This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layer(s). 1.2 This type of floor covering is intended for use in commercial and light commercial buildings. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Vinyl Sheet Floor Covering Without Backing