S61 信号器材 标准查询与下载

IEC 62280-1:2002 轨道交通.通信、信号和处理系统.第1部分:在封闭的传输系统中有关通信安全

This part of IEC 62280 is applicable to safety-related electronic systems using a closed transmission system for communication purposes. It gives the basic requirements needed in order to achieve safety-related communication between safety-related equipm

Railway applications - Communication, signalling and processing systems - Part 1: Safety-related communication in closed transmission systems

IEC 62280-2:2002 轨道交通.通信、信号和处理系统.第2部分:在开放的传输系统中有关通信安全

This part of IEC 62280 is applicable to safety-related electronic systems using an open transmission system for communication purposes. It gives the basic requirements needed, in order to achieve safety-related transmission between safety-related equipme

Railway applications - Communication, signalling and processing systems - Part 2: Safety-related communication in open transmission systems

TB/T 1528.6-2002 铁路信号电源屏.第6部分:区间信号电源屏

本部分规定了区间信号电源屏(以下简称电源屏)的术语和定义、产品分类、技术要求、检验规则、标志、包装、运输、贮存等。 本部分适用于区间信号设备的供电电源设备。

Railway signal power supply panel-Part 6: Block section signal power supply panel

TB/T 1528.7-2002 铁路信号电源屏.第7部分:25Hz信号电源屏

本部分规定了25H z信号电源屏(以下简称电源屏)的术语和定义、产品分类、技术要求、检验规则、标志、包装、运输、贮存等。 本部分适用于25H z信号设备的供电电源设备。

Railway signal power supply panel-Part 7: 25Hz signal power supply panel

TB/T 1528.1-2002 铁路信号电源屏.第1部分:总则

本部分规定了铁路信号电源屏(以下简称电源屏)的术语和定义、产品分类、技术要求、检验规则、标志、包装、运输、贮存等。 本部分适用于铁路信号继电联锁、计算机联锁、驼峰信号、25H z相敏轨道电路、区间自动闭塞等设备的供电电源设备

Railway signal power supply panel-Part 1: General rules

TB/T 1528.3-2002 铁路信号电源屏.第3部分:继电联锁信号电源屏

本部分规定了继电联锁信号电源屏(以下简称电源屏)的术语和定义、产品分类、技术要求、检验规则、标志、包装、运输、贮存等。 本部分适用于继电联锁信号设备的供电电源设备。

Railway signal power supply panel-Part 3: All-relay interlocking signal power supply panel

TB/T 1528.4-2002 铁路信号电源屏.第4部分:计算机联锁信号电源屏

本部分规定了计算机联锁信号电源屏(以下简称电源屏)的术语和定义、产品分类、技术要求、检验规则、标志、包装、运输、贮存等。 本部分适用于计算机联锁信号设备的供电电源设备。

Railway signal power supply panel-Part 4: Computer -interlocking signal power supply panel

TB/T 3069-2002 S700K-C型电动转辙机

本标准规定了S700K-C型电动转辙机(以下简称转辙机)产品的基本参数、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于转辙机的设计、制造、检验和维修。

S700K-C electric switch machine

IEC 62279:2002 轨道交通.通信,信号和处理系统.铁路控制和保护系统用软件

Specifies procedures and technical requirements for the development of programmable electronic systems for use in railway control and protection applications. Aimed at use in any area where there are safety implications. These may range from the very cri

Railway applications - Communications, signalling and processing systems - Software for railway control and protection systems

DIN EN 50159-1:2001 轨道交通.通信、信号传输和处理系统.第1部分:封闭式传输系统中与安全有关的通信; 德文版本 EN 50159-1:2001

Railway applications - Communication, signalling and processing systems - Part 1: Safety-related communication in closed transmission systems; German version EN 50159-1:2001

JIS E 3016:2001 电动道口栏杆性能的试验方法

この規格は，鉄道用電気踏切遮断機(以下，遮断機という。)の性能試験方法について規定する。

Performance test methods for motor-operated barriers

TB/T 1413-2001 透镜式色灯信号机构及信号表示器

本标准规定了透镜式色灯信号机构及信号表示器的产品分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于透镜式色灯信号机构及信号表示器(以下简称机构)的制造和检验。

Lens type color light signal mechanism and signal indicator

BS EN 50159-2:2001 轨道交通.通信,信号和处理系统.开放运输系统通信 安全

This European Standard is applicable to safety related electronic systems using an open transmission system for communication purposes. It gives the basic requirements needed in order to achieve safety related transmission between safety related equipment connected to the open transmission system. This standard is applicable to the safety requirement specification of the safety related equipment, connected to the open transmission system, in order to obtain the allocated safety integrity level. The properties and behaviour of the open transmission system are only used for the definition of the performance, but not for safety. Therefore from the safety point of view the open transmission system can potentially have any property, as various transmission ways, storage of messages, unauthorized access, etc. The safety process shall only rely on properties which are demonstrated in the safety case. The safety requirement specification is a precondition of the safety case of a safety related electronic system for which the required evidences are defined in ENV 50129. Evidence of safety management and quality management has to be taken from ENV 50129. The communication related requirements for evidence of functional and technical safety are the subject of this standard. This standard is not applicable to existing systems, which had already been accepted prior to the release of this standard. This standard does not specify: - the open transmission system; - equipment connected to the open transmission system; - solutions (e.g. for interoperability); - which kinds of data are safety related and which are not.

Railway applications. Communication, signalling and processing systems. Part 2: Safety related communication in open transmission systems

BS EN 50159-1:2001 轨道交通.通信,信号和处理系统.封闭运输系统通信安全

This European Standard is applicable to safety-related electronic systems using a closed transmission system for communication purposes. It gives the basic requirements needed in order to achieve safety-related communication between safety-related equipment connected to the transmission system. This standard is applicable to the safety requirement specification and design of the communication system in order to obtain the assigned safety integrity level (SIL). The safety requirement specification is a precondition of the safety case of a safety-related electronic system for which the required evidence is defined in EN 50129. Evidence of safety management and quality management has to be taken from EN 50129. Evidence of functional and technical safety is the subject of this standard. This standard is not applicable to existing systems which had already been accepted prior to the release of this standard. However, as far as is reasonably practicable, this standard shall be applied to modifications and extensions to existing systems, subsystems and equipment. This standard applies to a closed transmission system with the following preconditions, for which evidence shall be provided. 1) Only approved access is permitted. 2) There is a known maximum number of connectable participants. 3) The transmission media is known and fixed. Closed transmission systems are not necessarily data buses. They can also include for instance balise links or simple serial links between two safety-related computers. In particular this standard does not define the following. - The transmission system. - The equipment connected to the transmission system. - Specific solutions (e.g. for interoperability). - Which kinds of data are safety-related and which aren’t.

Railway applications. Communication, signalling and processing systems. Part 1: Safety–related communication in closed transmission systems

BS EN 50128:2001 轨道交通.通信、信号和处理系统.铁路控制和防护系统用软件

1.1 This European Standard specifies procedures and technical requirements for the development of programmable electronic systems for use in railway control and protection applications. It is aimed at use in any area where there are safety implications. These may range from the very critical, such as safety signalling to the non-critical, such as management information systems. These systems may be implemented using dedicated microprocessors, programmable logic controllers, multiprocessor distributed systems, larger scale central processor systems or other architectures. 1.2 This European Standard is applicable exclusively to software and the interaction between software and the system of which it is part. 1.3 Software safety integrity levels above 0 are for use in systems in which the consequences of failure could include loss of life. Economic or environmental considerations, however, may also justify the use of higher software safety integrity levels. 1.4 This European Standard applies to all software used in development and implementation of railway control and protection systems including: – application programming; – operating systems; – support tools; – firmware. Application programming comprises high level programming, low level programming and special purpose programming (for example: Programmable Logic Controller ladder logic). 1.5 The use of standard, commercially available software and tools is also addressed in this European Standard. 1.6 This European Standard also addresses the requirements for systems configured by application data. 1.7 This European Standard is not intended to address commercial issues. These should be addressed as an essential part of any contractual agreement. All the clauses of this European Standard will need careful consideration in any commercial situation. 1.8 This European Standard is not intended to be retrospective. It therefore applies primarily to new developments and only applies in its entirety to existing systems if these are subjected to major modifications. For minor changes, only clause 16 applies.

Railway applications. Communications, signalling and processing systems. Software for railway control and protection systems

BS EN 50149:2001 轨道交通.固定置装.电力牵引.铜和铜合金波纹连接线

This standard specifies the characteristics of copper and copper alloy wires of cross-sections of 80, 100, 107, 120 and 150 mm for use on overhead contact lines. It establishes the product characteristics, the test methods, checking procedures to be used with the wires, together with the ordering and delivery condition.

Railway applications - Fixed installations - Electric traction - Copper and copper alloy grooved contact wires

TB 10070-2000 铁路区间道口信号设计规范

Code for design of railway wayside crossing signaling

TB 10071-2000 铁路信号站内联锁设计规范

Code for design of railway signal interlocking within stations

TB/T 3303-2000 铁路车站旅客引导显示系统设置标准

本标准规定了铁路车站旅客引导显示系统的设置地点、显示内容、显示装置和控制系统主要技术要求等内容。

Setting Standards for Passenger Guidance and Display System in Railway Stations

TB/T 1777-2000 铁路车站客运广播设备制式系列及主要技术条件

本标准规定了铁路车站客运广播设备制式系列、主要功能、技术指标和设备结构要求。 本标准适用于铁路车站客运广播设备的产品设计、制造和工程设计。

Standard series and main technical conditions of passenger transport broadcasting equipment in railway stations