U12 船体通用结构 标准查询与下载

ASTM F1138-98(2007) 机械连接挡溅板的标准规范

1.1 This specification describes the manufacturing requirements for spray shield stock and the fabrication and installation requirements for spray shields made from that stock. 1.1.1 Sections 2-14 address the manufacturing requirements for the spray shield stock. Annex A1 addresses the fabrication and installation requirements for the spray shields. 1.1.2 Fig. 1 shows the typical construction of a spray shield. Figs. 2-6 show methods of installation of a spray shield on various mechanical joints. 1.2 The shields are intended for use around mechanical joints (flanged, bolted unions, and so forth) in liquid piping systems to prevent the impingement of flammable liquid on hot surfaces or fluids onto electrical switchboards and components resulting from a leak in the mechanical joint. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Spray Shields for Mechanical Joints

ASTM F1143-98 防油防水隆起的螺栓连接检查孔盖组件标准规范

1.1 This specification provides design and construction criteria for a raised, bolted, oiltight, and watertight manhole cover assembly. 1.2 The manhole cover assemblies depicted in this specification are for use in decks or bulkheads where the manhole cover assemblies must be of the raised type. Manhole cover shall be complete with coaming, gasket, welded studs or bolts, washers, and nuts. 1.3 Determination of the use of handles will be as specified in the ordering information. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This specification is not applicable to certain hazardous cargos (see 46CFR 153.254 and 46CFR 154.340). 1.6 This specification provides design and construction for manhole cover assemblies subjected to lateral pressures such as resulting from vehicle loads or hydrostatic pressures. Where manhole cover assemblies are subjected to primary or cyclic loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly, Bolted, Raised, Oiltight and Watertight

ASTM F1138-98 机械连接挡溅板标准规范

1.1 This specification describes the manufacturing requirements for spray shield stock and the fabrication and installation requirements for spray shields made from that stock. 1.1.1 Sections 2 through 14 address the manufacturing requirements for the spray shield stock. Annex A1 addresses the fabrication and installation requirements for the spray shields. 1.1.2 Fig. 1 shows the typical construction of a spray shield. Figs. 2 through 6 show methods of installation of a spray shield on various mechanical joints. 1.2 The shields are intended for use around mechanical joints (flanged, bolted unions, etc.) in liquid piping systems to prevent the impingement of flammable liquid on hot surfaces or fluids onto electrical switchboards and components resulting from a leak in the mechanical joint. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Spray Shields for Mechanical Joints

ASTM F1144-98(2003) 防油防水半嵌入螺栓铰接检查孔盖组件

1.1 This specification provides design and construction criteria for a semi-flush, oiltight and watertight bolted hinged manhole cover assembly.1.2 The manhole cover assemblies depicted on this specification are for use in decks or bulkheads requiring oiltight and watertight covers that are not required to be completely flush. Manhole cover assemblies shall be complete with covers, mounting rings, gaskets, studs, washers, hinge assemblies, and nuts.1.3 Handles, if required, shall be as specified in the ordering information.1.4 Values stated in inch-pound units are to be regarded as standard.1.5 This standard is not applicable to certain hazardous cargos. (See 46CFR 153.254 and 46CFR 154.340.) 1.6 This specification provides design and construction for manhole cover assemblies subjected to lateral pressures such as resulting from vehicle loads or hydrostatic pressures. Where manhole cover assemblies are subjected to primary or cyclic loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight, Hinged

ASTM F1138-98(2003) 机械连接挡溅板标准规范

1.1 This specification describes the manufacturing requirements for spray shield stock and the fabrication and installation requirements for spray shields made from that stock.1.1.1 Sections 2-14 address the manufacturing requirements for the spray shield stock. Annex A1 addresses the fabrication and installation requirements for the spray shields.1.1.2 Fig. 1 shows the typical construction of a spray shield. Figs. 2-6 show methods of installation of a spray shield on various mechanical joints.1.2 The shields are intended for use around mechanical joints (flanged, bolted unions, and so forth) in liquid piping systems to prevent the impingement of flammable liquid on hot surfaces or fluids onto electrical switchboards and components resulting from a leak in the mechanical joint.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Spray Shields for Mechanical Joints

ASTM F1142-98 防油和防水半嵌入螺栓连接检查孔盖组件用标准规范

1.1 This specification provides design and construction criteria for a semi-flush, oiltight, and watertight bolted manhole cover assembly. 1.2 The manhole cover assembly depicted in this specification is for use in decks or bulkheads requiring oiltight and watertight covers that are not required to be completely flush. Manhole cover assemblies shall be complete with covers, mounting rings, gaskets, welded studs, washers, and nuts. 1.3 Handles, if required, shall be as specified in the ordering information. 1.4 The values stated in inch pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This specification is not applicable to certain hazardous cargos (see 46CFR 153.254 and 46CFR 154.340). 1.6 This specification provides design and construction for manhole cover assemblies subjected to lateral pressures such as resulting from vehicle loads or hydrostatic pressures. Where loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly Bolted, Semi-Flush, Oiltight and Watertight

ANSI/ASTM F1099M:1998 船用防鼠装置规范(公制)

Specification for Rat Guards, Ships (Metric)

ASTM F1142-98(2003) 防油防水半嵌入螺栓连接检查孔盖组件标准规范

1.1 This specification provides design and construction criteria for a semi-flush, oiltight, and watertight bolted manhole cover assembly.1.2 The manhole cover assembly depicted in this specification is for use in decks or bulkheads requiring oiltight and watertight covers that are not required to be completely flush. Manhole cover assemblies shall be complete with covers, mounting rings, gaskets, welded studs, washers, and nuts.1.3 Handles, if required, shall be as specified in the ordering information.1.4 The values stated in inch pound units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This specification is not applicable to certain hazardous cargos (see Section 46 CFR 153.254 and 46 CFR 154.340).1.6 This specification provides design and construction for manhole cover assemblies subjected to lateral pressures such as resulting from vehicle loads or hydrostatic pressures. Where manhole cover assemblies are subjected to primary or cyclic loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly Bolted, Semi-Flush, Oiltight and Watertight

ASTM F1144-98 防油防水半嵌入螺栓铰接检查孔盖组件

1.1 This specification provides design and construction criteria for a semi-flush, oiltight and watertight bolted hinged manhole cover assembly. 1.2 The manhole cover assemblies depicted on this specification are for use in decks or bulkheads requiring oiltight and watertight covers that are not required to be completely flush. Manhole cover assemblies shall be complete with covers, mounting rings, gaskets, studs, washers, hinge assemblies, and nuts. 1.3 Handles, if required, shall be as specified in the ordering information. 1.4 Values stated in inch-pound units are to be regarded as standard. 1.5 This standard is not applicable to certain hazardous cargos. (See 46CFR 153.254 and 46CFR 154.340.) 1.6 This specification provides design and construction for manhole cover assemblies subjected to primary or cyclic loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight, Hinged

ASTM F1143-98(2003) 防油防水隆起的螺栓连接检查孔盖组件标准规范

1.1 This specification provides design and construction criteria for a raised, bolted, oiltight, and watertight manhole cover assembly.1.2 The manhole cover assemblies depicted in this specification are for use in decks or bulkheads in which the manhole cover assemblies must be of the raised type. Manhole cover shall be complete with coaming, gasket, welded studs or bolts, washers, and nuts.1.3 Determination of the use of handles will be as specified in the ordering information.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This specification is not applicable to certain hazardous cargos (see Section 46 CFR 153.254 and 46 CFR 154.340).1.6 This specification provides design and construction for manhole cover assemblies subjected to lateral pressures such as resulting from vehicle loads or hydrostatic pressures. Where manhole cover assemblies are subjected to primary or cyclic loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly, Bolted, Raised, Oiltight and Watertight

ASTM F1144-98(2007) 防油防水半嵌入螺栓连接检查孔盖组件标准规范

1.1 This specification provides design and construction criteria for a semi-flush, oiltight and watertight bolted hinged manhole cover assembly. 1.2 The manhole cover assemblies depicted on this specification are for use in decks or bulkheads requiring oiltight and watertight covers that are not required to be completely flush. Manhole cover assemblies shall be complete with covers, mounting rings, gaskets, studs, washers, hinge assemblies, and nuts. 1.3 Handles, if required, shall be as specified in the ordering information. 1.4 Values stated in inch-pound units are to be regarded as standard. 1.5 This standard is not applicable to certain hazardous cargos. (See 46CFR 153.254 and 46CFR 154.340.) 1.6 This specification provides design and construction for manhole cover assemblies subjected to lateral pressures such as resulting from vehicle loads or hydrostatic pressures. Where manhole cover assemblies are subjected to primary or cyclic loads, other reinforcement or construction criteria may be necessary to integrate the manhole assembly with the required structural reinforcement for openings in decks or bulkheads. Design of the manhole cover assembly for primary or cyclic loads is beyond the scope of this specification.

Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight, Hinged

NAVY MIL-PRF-29163 C-1997 标记浮标(十进制)

This specification covers marker buoys that are used with and without mooring (see 6.1).

BUOYS, MARKER (METRIC)

JT/T 308-1997 钢筋混凝土船船体建造技术条件

本标准规定了建造钢筋混凝土船船体的原材料和各工序的工艺要求。 本标准适用于建造沿海、内河或特定水域的各种非自航钢筋混凝土船舶。 对于钢筋混凝土水上漂浮构筑物以及采用钢质、钢丝网水泥或其它材料建造的混合结构船，其钢筋混凝十结构部分可参照使用。

Regulations for hull construction of reinforced concrete ships

NAVY MIL-L-19140 E (2)-1997 阻滞剂处理的木材和夹板(代替:NAVY MIL-L-0019140 D)

This amendment forms a part of MIL-L-19140E, dated 28 June 1984, and is approved for use by all Departments and Agencies of the Department of Defense.

LUMBER AND PLYWOOD, FIRE-RETARDANT TREATED [Use In Lieu Of: NAVY MIL-L-0019140 D]

CB 908-1996 舷侧附件安装用螺柱和螺母规范

1.1 主题内容 本规范规定了舷侧附件安装用螺柱和螺母的型式、尺寸、材料、制造及质量保证规定。 1.2 适用范围 本规范适用于潜艇。深潜器可参照使用。 1.3 分类 本规范的螺柱分为下列两种型式； a．A型不等长双头螺柱； b．B型等长双头螺柱；

Specification for studs and nuts for mounting side accessories

CB 1309-1996 水面舰船甲板、通道、舱室编号方法

本标准规定了水面舰船甲板、通道、舱室编号的方法。 本标准适用于水面舰船。其它舰船可参照使用。

Method of numbering decks, passages and compartments of surface warships

ISO/TR 14564:1995 造船及海上结构物 逃生路线标志

Relates to the marking of escape routes on board of ferries, passenger ships cargo ships etc.. Signs and posters which are used as marking are classified into categories in terms of purpose.

Shipbuilding and marine structures - Marking of escape routes

NAVY MIL-DTL-22342 E-1995 梁和桁架制成铝窗楣

This specification covers aluminum beam and truss brows

BROWS, ALUMINUM, BEAM AND TRUSS

NF J83-211:1995 内河航行船舶.甲板围栏.要求、类型

Inland navigation vessels. Railings for decks. Requirements, types.

CB/T 3655-1994 机舱集控室设计规则

本标准规定了船舶机舱集控室的功能、工作条件、布置、设备、结构及环境条件等设计要求。 本标准主要适用于自动化程度较高的大中型船舶，其它船舶亦可参照使用。

Design rules for engine room centralized control room