V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3198L-2014 中硬度氯丁海绵橡胶

This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, medium sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.

Sponge, Chloroprene (CR) Rubber, Medium Stiffness

SAE AMS3250K-2014 通用软质合成橡胶和软木合成物

This specification covers a synthetic rubber and cork composition in the form of sheet, strip, and molded shapes.

Synthetic Rubber and Cork Composition, General Purpose, Soft

SAE AMS3199L-2014 坚硬氯丁海绵橡胶

This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, firm sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.

Sponge, Chloroprene (CR) Rubber, Firm

SAE AMS2980/5A-2014 碳纤维织物和环氧树脂湿浸渍增强修复材料.第5部分:材料规范:平织、193 g/m²环氧和碳纤维织物

This Material Specification defines the requirements of carbon fiber fabric and epoxy resin systems used for wet lay-up repair of carbon fiber reinforced epoxy structures, qualified according to AMS 2980/1 and 2980/2.

Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 5 - Material Specification: Carbon Fiber Fabrics, Plain Weave, 193 g/m2, and Epoxy Resin

SAE AMS2980/2B-2014 技术规范:碳纤维织物和环氧树脂湿浸渍增强修复材料.第2部分:合格鉴定计划

AMS 2980/2 gives specific information about the qualification program for carbon fiber fabric, epoxy systems and the material combination used for wet lay-up repair of carbon fiber reinforced epoxy structures.

Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 2 - Qualification Program

SAE AMS2980/3B-2014 技术规范:碳纤维织物和环氧树脂湿浸渍增强修复材料采购规范.织物

The PS specifies the batch release and delivery requirements for carbon fiber and carbon fabric used for wet lay-up repair purposes.

Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Purchasing Specification - Fabric

SAE AMS2980/1B-2014 技术规范:碳纤维织物和环氧树脂湿浸渍增强修复材料.第1部分:一般要求

AMS 2980/1 gives information about the technical requirements and qualification procedure for carbon fiber fabric and epoxy resin systems used for wet lay-up repair of carbon fiber reinforced epoxy structures.

Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 1 - General Requirements

SAE AMS2980/4B-2014 技术规范:碳纤维织物和环氧树脂湿浸渍增强修复材料采购规范.树脂

This PS specifies the batch release and delivery requirements for epoxy resin systems (base resin and curing agent) used for wet lay-up repair purposes.

Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Purchasing Specification - Resin

SAE AMS3226H-2014 耐热油和冷却剂的丁腈橡胶.低膨胀,45-55

This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for hose, packings, bushings, grommets, and seals in contact with hot, petroleum-base lubricating oils and glycol-type coolants from -40 degrees to +100 degrees C (-40 degrees to +212 degrees F).

Acrylonitrile Butadiene (Nbr) Rubber, Hot Oil and Coolant Resistant, Low Swell, 45-55

SAE AMS3212P-2014 耐芳族燃料苯烯腈-丁二烯橡胶,55-65

This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves, requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both, but usage is not limited to such applications.

Acrylonitrile Butadiene (Nbr) Rubber, Aromatic Fuel Resistant, 55-65

SAE AMS3209M-2014 氯丁二烯(CR)耐风化橡胶65-75

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.

Chloroprene (CR) Rubber, Weather Resistant, 65 - 75

SAE AMS3208N-2014 不受天气影响45-55的氯丁二烯(CR)橡胶

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.

Chloroprene (CR) Rubber, Weather Resistant, 45 - 55

SAE AMS3207N-2014 氯丁二烯(CR)耐风化橡胶25-35

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, and molded shapes.

Chloroprene (CR) Rubber, Weather Resistant, 25 - 35

SAE AMS2980B-2014 技术规范:碳纤维织物和环氧树脂潮湿堆积修复材料.第0部分:介绍

This document (Technical Specification) gives information about qualification rules and the relation between the different specification parts involved, such as Technical Specification (TS), Material Specification (MS), and Purchasing Specification (PS). The link to material qualification and qualified products is presented.

Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material, Part 0 - Introduction

NF L17-099*NF EN 3102:2014 航空航天系列. 密封剂. 试验方法. 低温柔韧性的测定

La présente norme européenne définit la méthode d'essai pour la détermination de l'opérabilité d'un produit d'étanchéité pendant ou après l'application d'une charge de pliage à basses températures (flexibilité à basse température).

Aerospace series - Sealants - Test methods - Determination of low-temperature flexibility

BS ISO 16691:2014 空间系统. 航天器的热控涂层. 一般要求

Space systems. Thermal control coatings for spacecraft. General requirements

NF L16-021*NF EN 4594:2014 航空航天系列. 涂料和清漆. 双组分冷固化聚氨酯罩面漆. 超音速耐腐蚀性

La présente Norme européenne spécifie les exigences d'une couche de finition polyuréthane, à deux composants, degré moyen de résistance à l'érosion due aux effets de la pluie, disponible dans une gamme de couleurs et de niveaux de brillance, applicable sur une peinture primaire pour applications aérospatiales sur des zones où l'érosion par la pluie à des vitesses supersoniques peut constituer un problème par ex. bord d'attaque et entrées d'air.Les propriétés spécifiées dans la présente norme sont obtenues sur des éprouvettes en alliage d'aluminium définies conformément à l'EN 3837 Procédure A et l'EN 23270 et peintes avec un primaire selon l'EN 2435.L'aptit

Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Supersonic erosion resistance

NF L16-022*NF EN 4595:2014 航空航天系列. 涂料和清漆. 双组分冷固化聚氨酯罩面漆. 亚音速耐腐蚀性

La présente Norme européenne spécifie les exigences d'une couche de finition polyuréthane, à deux composants, degré moyen de résistance à l'érosion liée aux effets de la pluie, disponible dans une gamme de couleurs et de niveaux de brillance, applicable sur une peinture primaire pour applications aérospatiales sur des zones où l'érosion par la pluie à des vitesses subsoniques peut constituer un problème par ex. bord d'attaque et entrées d'air.Les propriétés spécifiées dans la présente norme sont obtenues sur des éprouvettes en alliage d'aluminium définies conformément à l'EN 3837 Procédure A et l'EN 23270 et peintes avec un primaire selon l'EN 2435.L'aptitu

Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Subsonic erosion resistance

DIN EN 3866:2014 航空航天系列.非金属材料.玻璃软片.试验方法.绞孔和表面波纹的测定.德文和英文版本EN 3866-2013

Aerospace series - Non-metallic materials - Glass tranparencies - Test methods - Determination of ream and surface ripple; German and English version EN 3866:2013

DIN EN 2833-005:2014 航空航天系列. 玻璃纤维热固预浸渍物. 技术规范. 第005部分: 玻璃纤维/酚醛树脂预浸渍物; 德文和英文版本EN 2833-005-2013

Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 005: Glass fabric/phenolic resin preimpregnate; German and English version EN 2833-005:2013