V13 航空与航天用非金属材料 标准查询与下载

NF L17-705*NF EN 3861:2013 航空航天系列.非金属材料.玻璃透明胶片.材料标准.热钢化碱石灰浮法玻璃

Aerospace series - Non-metallic materials - Glass transparencies - Material standard - Thermally tempered soda lime float glass

SAE AMS3126D-2013 无机粘胶剂热固防腐和防热铝涂层材料

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a corrosion and heat resistant aluminum coating material supplied as a liquid of suitable consistency for coating parts after being thoroughly mixed. Primarily for coating ferrous parts to be exposed to temperatures below 650°C (1200°F).

Aluminum Coating Material, Corrosion and Heat Resistant, Thermosetting, Inorganic Binder

SAE AMS3145D-2013 标记环氧涂料

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers two-component colored systems composed of a resin and a miscible hardener supplied in kit form. Primarily for identification marking of parts and equipment exposed to temperatures from -55 to +150 degrees C (-65 to +300 degrees F) where various colors are needed. Systems produce tile-like compounds with good hardness, moisture and solvent resistance, and adhesion to metallic surfaces when properly

Paint, Marking Epoxy

SAE AMS3140B-2013 聚四氟乙烯填充的脂肪族异氰酸盐尿烷涂层

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared ""NONCURRENT"" by the Aerospace Materials Division, SAE, as of October, 2007. It is recommended, therefore, that this specification not be specified fro new designs. ""NONCURRENT"" refers to those specifications which have previously been widely used and which may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does

Coating, Urethane, Aliphatic Isocyanate, Polytetrafluoroethylene Filled

SAE AMS7290H-2013 贴花纸

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared ""CANCELLED"" by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been ""CANCELLED"". This specification covers face-up type of water applied, solvent-applied, or adhesive-applied decalcomanias. These decalcomanias have been used prima

Decalcomanias

SAE AS22759/54-2013 200℃、600 V正常重量镀银铜低氟改性乙烯四氟乙烯(ETFE)含氟聚合物绝缘交联电线

Wire, Electrical, Fluoropolymer-Insulated, Crosslinked Modified ETFE, Low Fluoride, Normal Weight, Silver-Coated Copper, 200 degree C, 600 Volt

SAE AMS3122G-2013 黑底苯酚瓷漆

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared ""CANCELLED"" by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been ""CANCELLED"". This specification covers a semigloss black baking enamel based on a phenolic resin. Primarily as a coating for metal surfaces exposed to corrosive c

Enamel, Phenolic, Black Baking

SAE AMS3799/2C-2013 抗断强度为2300(10231)、宽为3/4(19)的低模数芳香族管状织物带

This specification covers one width and one breaking strength of low modulus aramid tubular webbing.

Webbing, Tubular, Low Modulus Aramid 3/4 (19) Wide, 2300 (10 231) Breaking Strength

SAE AMS3217/5C-2013 55-65氟硅氧烷(FVMQ)试验板

This specification covers a standard fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.

Test Slabs, Fluorosilicone (FVMQ), 55-65

SAE AMS3346G-2013 最小拉伸强度为1000 psi(6.89 MPa)的硬度范围55-65的硅酮橡胶

This specification covers a silicone rubber material that can be used to manufacture product in the form of sheet, strip, tubing, molded shapes, and extrusions. This specification should not be used to address products such as O-rings, compression seals, O-ring cord, and molded-in-place gaskets.

Silicone Rubber, 1000 psi (6.89 MPa) Minimum Tensile Strength, 55-65 Durometer

SAE AMS3799/4C-2013 抗断强度为2250(10,008)、宽为3-3/16(81)的低模数芳香族管状织物带

This specification covers one width and one breaking strength of low modulus aramid tubular webbing.

Webbing, Tubular, Low Modulus Aramid 3-3/16 (81) Wide, 2250 (10 008) Breaking Strength

SAE AMS3799/3C-2013 抗断强度为4000(17793)、宽为1(25)的低模数芳香族管状织物带

This specification covers one width and one strength of low modulus aramid tubular webbing.

Webbing, Tubular, Low Modulus Aramid 1 (25) Wide, 4000 (17 793 ) Breaking Strength

NF L17-708*NF EN 3866:2013 航空航天系列 - 非金属材料 - 玻璃透明度 - 试验方法 - 绞孔和表面波纹测定

Aerospace series - Non-metallic materials - Glass transparencies - Test methods - Determination of ream and surface ripple

NF L17-707*NF EN 3863:2013 航空航天系列. 非金属材料. 玻璃透明度. 试验方法. 平整度测定

Aerospace series - Non-metallic materials - Glass transparencies - Test methods - Determination of flatness

NF L17-706*NF EN 3862:2013 航空航天系列.非金属材料.玻璃透明胶片.材料标准.化学钢化碱石灰浮法玻璃

Aerospace series - Non-metallic materials - Glass transparencies - Material standard - Chemically tempered soda lime float glass

SAE AMS2525D-2013 薄膜润滑膜撞击应用石墨涂层

This specification covers a coating consisting of finely-powdered graphite in a heat-resistant inorganic binder. This coating has been used typically on metal parts and selected nonmetallic materials requiring a coating less than 0.0001 inch (2.5 um) thick for reducing wear or minimizing galling, but usage is not limited to such applications.

Graphite Coating, Thin Lubricating Film Impingement Applied

EN 4507:2013 航空航天系列非金属材料纺织品试验方法水溶出物的测定

This European Standard specifies the procedure for the determination of water extractable matter of textile material. This method has been written in response to an aerospace requirement for a method of extraction using hot water.

Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter

EN 4505:2013 航空航天系列.非金属材料.纺织品.试验方法.尺寸稳定性测定

This European Standard specifies the procedure for the determination of dimensional stability of narrow fabrics.

Aerospace series - Non-metallic materials - Textiles - Test method - Determination of dimensional stability

EN 4503:2013 航空航天系列.非金属材料.纺织品.试验方法.水溶性氯化物和水提物硫酸盐的测定

This European Standard specifies the determination of water soluble chloride and sulphate of aqueous extracts of textile materials. This method has been written in response to an aerospace requirement for a method of extraction using hot water, this method should be used in conjunction with EN 4426.

Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water soluble chloride and sulfate of aqueous extracts

BS EN 3864:2013 航空航天系列. 非金属材料. 玻璃透明度. 试验方法. 断裂模量测定

Aerospace series. Non-metallic materials. Glass transparencies. Test methods. Determination of modulus of rupture