V16 热加工工艺 标准查询与下载

SAE AMS2670J-2006 铜焊

This specification covers the engineering requirements for producing brazed joints using copper as the brazing filler metal. This process has been used typically for joining carbon steels, low-alloy steels, and corrosion and heat resistant steels and alloys. It is not recommended for use on parts which will operate in service over 1000 degrees F (538 degrees C) or requiring high strength joints for service over 700 degrees F (371 degrees C), but usage is not limited to such applications.

Brazing, Copper [Superseded: SAE AMS 2671F]

NF L06-383:2006 航空航天系列.航空航天结构件的焊接和铜焊组件.电阻点焊或接缝焊接组件.焊接组件质量

Aerospace series - Welded and brazed assemblies for aerospace constructions - Resistance spot or seam welded assemblies - Quality of welded assemblies.

SAE AMS2759D-2006 钢零件热处理一般要求

This specification establishes general requirements for the processes listed in 3.3.1 for heat treatment of steel parts (See 8.2.1) by users or their vendors or subcontractors. Reference to AMS 2759 on a drawing, fabrication order, purchase order, etc constitutes a requirement to conform to the applicable provisions of the documents listed in 3.3.1 for the hear treatment of steel parts of the particular alloy described. Parts made from steels orther than those specified in the detail specifications may be heat treated in accordance with the applicable requirements using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by purchaser. The conditions (temperatures, soaking times, cooling rates, etc) used by material producers, forge shops, and foundries for qualification of response to heat treatment of their products shall conform to the requirements of the specifications listed in 3.3.1. Heat treatment of raw material by raw material producers, forge shops, or foundries should be in accordance with the material procurement specification. Processes such as vacuum-furnace heat treating, flame hardening, induction through-hardening, austempering, martempering, and hot oil quenching are recognized heat treating processes, but their requirements are not completely covered by this specification.

Heat Treatment of Steel Parts General Requirements

HB/Z 199-2005 钛合金锻造工艺

本指导性技术文件规定了钛合金锻造的分类、术语、设备、仪器和工装、坯料准备、锻造工艺、锻件热处理、质量控制和技术安全。 本指导性文件适用于TA1、TA2、TA3、TA7、TA11、TA12、TA15、TA19、TC1、TC2、TC4、TC6、TC11、TC17、TC18、TB6、TB8等航空用钛合金的锻造和环轧工艺。其他钛合金的锻造也可参照本指导性技术文件执行。

Forging techniques of titanium alloy

HB 6438-2005 飞机线束加工通用要求

本标准规定了飞机线束加工的通用方法和要求。 本标准适用于各种固定翼飞机、直升机、无人机和导弹线束加工设计和生产。

Gerneral requirements for procedures for wire harness of aircraft

HB 7772-2005 环氧树脂/碳纤维预浸料规范

本规范规定了环氧树脂/碳纤维预浸料的要求、质量保证规定、交货准备及说明事项等内容。 本规范适用于环氧树脂/碳纤维预浸料。

Specification for epoxy resin carbon fiber prepregs

BS EN 2731:2005 航空航天系列.镁合金钢MG-C46001 - T6.砂型铸造

This standard specifies the requirements relating to: Magnesium alloy MG-C46001 T6 Sand casting for aerospace applications.

Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting

DIN 65228:2005 航空航天.钎焊工能力鉴定试验.金属元件钎焊

This document is applicable to qualification testing of personnel (brazers) engaged in manual brazing of parts in aerospace construction. The application will ensure that such a test is carried out in accordance with a standard test specification on standard test pieces under standard conditions. A brazer qualification test properly passed in accordance with the terms of this standard ensures that the brazer concerned has proved that he prossesses at least the minimum degree of manual skills and technical knowledge demanded by the state of the art.

Aerospace - Qualification test of brazers - Brazing of metallic components

NAVY A-A-59782-2005 热转换清洁化合物

(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)

HEAT EXCHANGER CLEANING COMPOUND

SAE AS7109/3A-2005 扩散涂层工艺Nadcap要求

This SAE Aerospace Standard (AS) is to be used as a supplement to AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking Nadcap Coatings accreditation who are engaged in cementation.

(R) Nadcap Requirements for Diffusion Coating Processes

SAE AS7109/1A-2005 热喷涂Nadcap要求

This SAE Aerospace Standard (AS) is to be used as a supplement to AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking Nadcap Coatings accreditation who are engaged in thermal spray.

(R) Nadcap Requirements for Thermal Spray

SAE AS7109A-2005 覆层的Nadcap要求

This SAE Aerospace Standard (AS) establishes the requirements for suppliers of coatings services to be accredited by Nadcap in accordance with AS7003. The requirements obtained herein may be supplemented by additional requirements specified by Nadcap Coatings Task Group. Using the audit checklist (PRI AC7109) will ensure that accredited Coatings suppliers meet all of the requirements in this standard and all applicable supplementary standards.

(R) Nadcap Requirements for Coatings

SAE AS7109/7A-2005 覆层供应商用热处理Nadcap要求

This SAE Aerospace Standard (AS) is to be used as a supplement to AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking Nadcap Coatings accreditation who are engaged in heat treating. Demonstrated compliance (as described in AS7003) to AS7102 satisfies the requirements contained herein.

(R) Nadcap Requirements for Heat Treating for Suppliers of Coatings

SAE AS7109/6A-2005 覆层部件电镀的Nadcap要求

This SAE Aerospace Standard (AS) is to be used as a supplement to AS 7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking Nadcap Coatings accreditation who are engaged in plating of coated parts. Demonstrated compliance (as described in AS7003) to AS7108 satisfies the requirements contained herein.

(R) Nadcap Requirements for Plating of Coated Parts

SAE AS7109/4A-2005 覆层材料剥离的Nadcap要求

This SAE Aerospace Standard (AS) is to be used as a supplement to AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking Nadcap Coatings accreditation who are engaged in stripping of coated material. The requirements for accreditation for the following classifications are contained herein: a. electrolytic; b. mechanical 1) grit blast 2) grinding and 3) machining; c. water jet; d. molten salt; and e. chemical.

(R) Nadcap Requirements for Stripping of Coated Material

DIN 29591 Berichtigung 1:2005 航空航天焊接.焊接工人的资格检验.金属构件的焊接.对DIN 29591-2004的勘误

The document applies to qualification testing of welders for welding metallic components for aerospace purpose.

Welding in aerospace - Qualification testing of welders - Welding of metallic components, Corrigenda to DIN 29591:2004-10

NAVY QPL-2819-67-2005 热的绝缘木块

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest effective issue of the applicable specification.

INSULATION BLOCK, THERMAL

SAE AMS2774A-2005 锻造镍合金和钴合金部件的热处理

This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts made of wrought nickel or cobalt alloys, of raw materials during fabrication, and of fabricated assemblies in which wrought nickel or cobalt alloys are the primary structural components.

Heat Treatment Wrought Nickel Alloy and Cobalt Alloy Parts

SAE AMS2773A-2005 铸造镍合金和钴合金部件的热处理

This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts made of cast nickel or cobalt alloys and of fabricated assemblies in which cast nickel or cobalt alloys are the primary structural components. It is not intended to provide requirements for heat treating operations that are a responsibility of the casting supplier in meeting the requirements of the casting commodity specification.

Heat Treatment Cast Nickel Alloy and Cobalt Alloy Parts

SAE AMS2728A-2005 锻铜铍合金部件的热处理

This specification establishes the requirements for heat treatment of wrought copper beryllium parts by users or by their vendors or subcontractors. This specification is applicable to parts made from the following alloys: UNS C17000, UNS C17200, UNS C17300, UNS C17500, and UNS C17510.

Heat Treatment of Wrought Copper Beryllium Alloy Parts