V21 管件、卡箍、密封件 标准查询与下载

SAE AMS7256B-2014 85-95耐液压机液体和合成油的四氟乙烯/丙烯(FEPM) 橡胶密封圈

This specification covers a tetrafluoroethylene/propylene rubber (FEPM) in the form of molded rings.

Rings, Sealing, Tetrafluoroethylene/Propylene Rubber (Fepm) Hydraulic Fluid and Synthetic Oil Resistant 85 to 95

SAE AS568D-2014 O形环的航空航天尺寸标准

This SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available.

Aerospace Size Standard for O-rings

HB 8331-2013 发动机导管连接用接头或管嘴的熔焊端

本标准规定了发动机用导管连接件接头或管嘴的熔焊端的设计要求。 本标准适用于发动机用导管连接件接头或管嘴的熔焊端的设计。

Welded ends of fittings or nozzles for engine conduit connections

HB 8324-2013 发动机导管74°连接用直阳管嘴

本标准规定了发动机导管 74"连接用直阳管嘴(下称管嘴) 的结构、尺十和要求。 本标准适用于发动机外部管路的 74 连接用直阳管嘴。

Straight male nozzle for 74° connection of engine duct

HB 8330-2013 发动机导管连接用接头或管嘴的钎焊端

Brazed ends of fittings or nozzles for engine conduit connections

HB 8325-2013 发动机导管74°连接用直阴管嘴

Straight female nozzle for 74° connection of engine duct

HB 8328-2013 发动机导管连接用接头或管嘴设计方法

本标准规定了发动机导管连接用异型管接头或异型管嘴的设计方法】 本标准适用于工作压力不大于 28麝4Pa 的发动机导管连接件的设计 不适用于导管的法兰连接设计。

Method of designing couplings or nozzles for engine duct connections

HB 8327-2013 发动机用导管刚性连接件规范

Specification for conduit rigid connectors for engines

HB 8329-2013 发动机导管连接用异型接头或管嘴通用芯部设计要求

General core design requirements for special-shaped joints or nozzles for engine duct connections

HB 8326-2013 发动机用74°锥面管路连接组合导管

74° conical pipeline connection combination conduit for engine

DIN EN 4537-2:2014 航空航天系列. 带自润滑衬料提升载荷的耐腐蚀钢制有法兰的套筒. 第2部分: 尺寸与载荷. 英制系列; 德文和英文版本EN 4537-2-2009

Aerospace series - Bushes, flanged in corrosion-resisting steel with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series; German and English version EN 4537-2:2009

BS EN 4156:2013 航空航天系列.钢制带自调位双排滚球轴承和螺纹柄的杆端.耐蚀钢中内圈和滚珠.尺寸规格和荷载.英制系列

Aerospace series. Rod ends, with self-aligning double row ball bearings and threaded shank in steel. Inner ring and balls in corrosion resisting steel. Dimensions and loads. Inch series

SAE AS4140B-2013 非扩口异径体侧面回转三通管配件装配

Fitting Assy, Tee, Reducer, Swivel on Side, Reduced Body, Flareless

SAE AS4137B-2013 非扩口异径体45°回转弯头配件装配

Fitting Assy, Elbow, Reducer, 45°, Swivel, Reduced Body, Flareless

HB 8333-2013 发动机导管连接用74°锥面和球面连接的阴端头

74° Cone and Spherical Female Ends for Engine Conduit Connections

HB 8332-2013 发动机导管连接用74°锥面连接的阳端头

Male end with 74° cone connection for engine conduit connection

SAE ARP4727B-2013 密封压盖的设计以及密封挤压和密封压盖体积的计算

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Aerospace Recommended Practice (ARP) presents two BASIC language computer programs to promote and standardize the computation of installed O-ring cross-section deflection hereafter referred to as ""squeeze"" and the computation of gland volume. The two programs were written with line numbers and without use of any system specific BASIC commands to allow usage with as many systems as possible with a minimum of edit

Gland Design, Computation of Seal Squeeze and Gland Volume

SAE AS5550B-2013 5080 PSI超细牙螺纹非扩口到端口适配器环状锁定配件总装

Fitting Assembly, Ring Locked, Adapter, Flareless to Port, Extra Fine Threads, 5080 PSI

SAE AS5986C-2013 连接环孔连接到梁密封4000 PSI和5000 PSI /9/配件总装

Fitting Assembly, Adapter Ring Locked Port Connection to Beam Seal 4000 PSI and 5000 PSI /9/

SAE AS4459B-2013 额定压力3000磅/平方英寸(21 000 kPa)外部锻造流体系统管道配件

This SAE Aerospace Standard (AS) establishes the requirements for externally swaged tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10 500 Kpa), and D (3000 psi or 21 000 kPa), and in temperature types I (-65 to 160 degree F or -55 to 70 degree C), and II (-65 to 275 degree F or -55 to 135 degree C) of AS2001. This specificaiton covers a common Cres, titanium, and aluminum fittings that may be used for a range of operating pressures up to 3000 psi with different tubing materials and tubing wall thicknesses and is assembled with the same tooling in accordance with AS 5902.

Fittings, Tube, Fluid System 3000 psig (21 000 kPa) Rated Pressure, Externally Swaged, Specification for