共找到 2302 条与 管件、卡箍、密封件 相关的标准,共 154 页
Fitting, Adapter, Union and Reducer, Short Flareless to Boss
Hose Assembly, Polytetrafluoroethylene, Para Aramid Reinforced, 275°F, 4000 PSI, Flareless, Titanium Fittings, Straight to 45°
Hose Assembly, Polytetrafluoroethylene, Para Aramid Reinforced, 275°F, 4000 PSI, Flareless, Titanium Fittings, Straight to 90°
Fitting, Cross, Reducer, Flareless and Short Flareless
Fitting, Union, Bulkhead, Short Flareless
Fitting, Elbow, 90 degrees, Bulkhead, Short Flareless
Fitting, Tee, Bulkhead on Side, Short Flareless
Space systems. Bellows. Design and operation
This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10500 kPa), D (3000 psi or 21000 kPa), and E (4000 psi or 28000 kPa), and J (5000 psi or 35000 kPa) and in temperatures types I (-65 to 160 °F or -55 to 70 \mdC), II (-65 to 275 °F or -55 to 135 °C), and III (-65 to 400 °F or -55 to 200 °C) of AS2001.
Test Methods for Tube-Fitting Assemblies
General specification for hydraulic servo system safety and relief valve
This International Standard specifies general and detailed requirements for bellows used in space systems. It establishes requirements with regard to material, design, analysis, fabrication, material, testing, inspection and operation for space use. This International Standard is applicable to metallic bellows which are used as pressure bearing components and are integrated into a pressure system. This International Standard is not applicable to engine bellows or valve bellows.
Space systems - Bellows - Design and operation
This Aerospace Recommended Practice sets forth the guidelines for the use of non-black O-ring seals. Black is the preferred color for polymer types other than Silicone and Fluorosilicone. When a color other than black is to be used, those established by this document are the preferred.
Color Identification for O-Ring Seals
本标准规定了飞机维护用化学品对飞机结构铝合金搭接面(夹层)的腐蚀测试方法。 本标准适用于固体颗粒或液体的飞机维护用化学品的认证和批准。
Test method for sandwich corrosion test
本标准规定了判定飞机涡轮发动机清洗和维护用品对钛合金零件造成应力腐蚀倾向的试验方法。 本标准适用于评估清洗和维护用品在加热条件下对受力的钛合金造成裂纹的倾向。
Test method for stress-corrosion of titanium alloys by aircraft engine cleaning materials
Fitting, Tee, Standard and Reducer, 37° Spherical, Flared
This specification covers a corrosion and heat resistant steel in the form of two types of thin-wall, close-tolerance tubing 0.25 to 2.00 inches (6.4 to 50.8 mm) in nominal OD. This tubing has been used typically in high pressure hydraulic or pneumatic systems assembled with brazed joints, but usage is not limited to such applications.
Steel, Corrosion and Heat Resistant, Seamless and Welded Hydraulic Tubing 19Cr 9.5Ni 0.03C max Cold Drawn,1/8 Hard Temper
This specification covers a corrosion and heat resistant steel in the form of welded tubing. This tubing has been used typically for parts requiring corrosion resistance and high strength up to 600 °F (316 °C) after precipitation heat treatment, but usage is not limited to such applications. Certain design and processing procedures may cause this tubing to become susceptible to stress-corrosion cracking after precipitation heat treatment; ARP1110 recommends practices to minimize such conditions.
Steel, Corrosion and Heat Resistant, Welded Tubing 17Cr 7.1Ni 1.1Al Solution Heat Treated, Precipitation-Hardenable
This specification covers a corrosion and heat resistant steel in the form of thin-wall seamless tubing. This tubing has been used typically for parts, such as fluid lines, requiring high strength and oxidation resistance up to 800 °F (427 °C), but usage is not limited to such applications.
Steel, Corrosion and Heat Resistant, Seamless Tubing 16.5Cr 4.5Ni 2.9Mo 0.10N Annealed
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号