V57 特种车辆 标准查询与下载

BS 2G 219:1983 飞行器地面保障用电源的一般要求规范

Specifies electrical output characteristics, interface requirements between the aircraft and ground support electrical supplies and safety requirements.

Specification for general requirements for ground support electrical supplies for aircraft

ISO 6965:1982 航空器 装吊航空货运集装箱和大件货物的自行式龙门起重机 功能要求

Gives the requirements for a gantry capable of raising from the ground, transporting and stacking two high: corner fitting equipped air/surface intermodal containers per ISO 1496/7, surface container, equipped with 8 corner fittings per ISO 1161 and various pieces of outsize cargo. The methods and devices used to lift corner fitting containers with the unit shall comply with ISO 3874.

Aircraft; Self-propelled gantry for lifting air cargo containers and outsize cargoes; Functional requirements

ISO 6858:1982 航空器 地面保障电源 一般要求

Gives electrical output characteristics, and interface requirements, between an aircraft and ground support electrical supplies. Requirements for safety features are also included. The facilities covered by this International Standard are intended to supply power to an aircraft. In some cases the facility may also be capable of being used for aircraft engine starting.

Aircraft; Ground support electrical supplies; General requirements

DLA MS90908 REV B-1982 填料 油舱 军用车辆

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

FILLER TUBE, FUEL TANK - MILITARY VEHICLES

AIR FORCE MIL-C-26339 C-1982 积雪型全面跟踪客运货运承运人的公用设施

This specification covers five sizes of cargo, utility and passenger carrying, full tracked, arctic tracklaying vehicles.

CARRIER, PASSENGER, CARGO, UTILITY, FULL TRACK, OVER-THE-SNOW TYPE

DIN ISO 43:1981 航空航天.飞机.千斤顶支板

Aerospace; aircraft; jacking pads

NAVY MS16957 REV B-1981 基于24的10000磅容量的货车钩型叉架

This specification covers a two -component epoxy cement for use in filling rough or pitted metal surfaces.

HOOK TYPE FORK MOUNTING FOR TRUCKS OF 10,000 POUNDS CAPACITY BASED ON 24" LOAD CENTER

NAVY MS16956 REV B-1981 基于24的6000磅容量的货车钩型叉架

Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS ran.nnm I -un

HOOK TYPE FORK MOUNTING FOR TRUCKS OF 6,000 POUNDS CAPACITY BASED ON 24" LOAD CENTER

ISO 43:1976 航空器千斤顶基座

Specifies the profiles and dimensions of main and axle jacking pads and the clear space to be provided around these pads. They are to be limited to the six designs shown in the figures 1 to 6, which specify the shape, size and clearances to be provided around the pads.

Aircraft jacking pads

ISO 451:1976 飞机.压力加注润滑油接头

Includes the basic dimensions for use with all oils for aircraft engines, and the clearance envelope to be provided. The dimensions and tolerances of the connection and space envelope are given in the figure and the table.

Aircraft; Pressure re-oiling connection

ISO 450:1976 飞机.饮用水的管接头

Aircraft; Connection for water of drinkable quality

AIR FORCE MIL-C-27840 C (1)-1975 A/S32H-11型4000磅重容量4 X 4车载起重机

This amendment forms a part of Military Specification MIL-C-Z7840C(USAF) dated 12 April 1966

CRANE, TRUCK MOUNTED A/S32H-11, 4,000 POUND CRANE CAPACITY, 4 X 4

ISO 413:1974 航空器 润滑油加油管嘴的头部

Specifies the envelope dimensions of axial type nipples and determines the clearance space which shall be provided in the region of the nipple to allow the lubricating gun to be connected, and the operating angle dimensions for the lubricating process. The tip design of the nipples is optional provided the profile remains within the envelope shown in figure 1.

Aircraft; Heads of lubricating nipples

ISO 2026:1974 航空器 发动机空气起动连接装置

Specifies the dimensions which are necessary to ensure international interchangeability of connectors with adaptors. Also gives the minimum clearances required on the aircraft to provide adequate access for the ground adaptor. The basic dimensions and tolerances for connections on aircraft and the minimum clearances around the connector, on the aircraft, are given in figure 1 and table 1 and figure 2 and table 2, respectively.

Aircraft; Connections for starting engines by air

ISO 46:1973 航空器 燃油管嘴接地插头和插座

Includes the dimensions of grounding plugs to be attached by cable to the nozzles of aircraft refuelling tankers. Details are also given of the sockets to be provided in the aircraft for the accomodation of the plugs and the minimum length, minimum diameter and material of the grounding cable.

Aircraft; Fuel nozzle grounding plugs and sockets

ISO 1034:1973 航空器 地面空气调节连接接头

Gives the requirements for 127 mm and 203 mm connections for the purpose of air-conditioning from ground sources. The conncetions shall comply with the basic dimensional requirements shown in either figure 1 or figure 2 as appropriate. The ground unit must not project more than 14,O mm beyond the sealing plane except through defined openings.

Aircraft; Ground air-conditioning connections

ISO 485:1973 航空器的水-甲醇压力加注接头

Gives the dimensions of 19 mm and 38 mm bore pressure connections. A space envolope is also specified for each size of connection. Dimensions and tolerances for connections are given in figures 1 and 3, and those for space envelopes in figures 2 and 4. The values are listed in tables.

Aircraft water-methanol pressure connections

AIR FORCE MIL-L-6378 C-1968 折叠加油梯

This specification is mandatory for use by a l l Departments and Agencies of the Department of Defense.

LADDERS, FOLDING REFUELING

AIR FORCE MIL-C-27840 C-1966 A/S32H-11型4000磅重容量4 X 4车载起重机

This specification covers one type of truck-mounted crane, designated A/S32H-ll.

CRANE, TRUCK MOUNTED A/S32H-11, 4,000 POUND CRANE CAPACITY, 4 X 4

NAVY MS16955 REV A-1964 基于24的2000和4000磅容量的货车钩型叉架

IN ACCORDANCE WITH SPECIFICATIONS. NOTCH SPACING [AITO BE I 1/2 INCHES.

HOOK TYPE FORK MOUNTING FOR TRUCKS OF 2000 AND 4000 POUNDS CAPACITY BASED ON 24" LOAD CENTER