This part of GB/T 13663 specifies the terms and definitions, symbols, abbreviations, materials and hygienic requirements for polyethylene (PE) piping systems for water supply. This part, together with other parts of GB/T 13663, applies to polyethylene piping systems and their components for general-purpose pressure water transmission and drinking water distribution with a water temperature not greater than 40 °C and a maximum operating pressure (MOP) not greater than 2.0 MPa .
GB/T 13663.1-2017 Referenced Document
GB/T 1033.1-2008 Plastics.Methods for determining density of non-celluar plastics.Part1:Immersion method,liquid pyknometer method and titration method
GB/T 1033.2-2010 Plastics.Methods for determining the density of non-cellular plastics.Part 2:Density gradient column method
GB/T 1040.2-2006 Plastics. Determination of tensile properties. Part 2: Test conditions for moulding and extrusion plastics
GB/T 13021-1991 Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis
GB/T 17219 Standard for safety evaluation of equipment and protective materials in drinking water system
GB/T 18251-2000 Method for the assessment of pigment or carbon black dispersion in polyolefin pipes,fittings and compounds
GB/T 18252 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation*, 2020-11-19 Update
GB/T 1845.2-2006 Plastics.Polyethylene (PE) moulding and extrusion materials.Part 2: Preparaation of test specimens and determination of properties
GB/T 18475 Thermoplastics materials for pipes and fittings for pressure applications classification and designation--Overall Service(design) coefficient
GB/T 18476-2001 Polyolefin pipes for the conveyance of fluids--Determination of resistance to crack propagation-Test method for slow crack growth on notched pipes(notch test)
GB/T 19278-2003 General terms and their definitions of thermoplastic pipes,fittings and valves
GB/T 19280-2003 Thermoplastics pipes for the conveyance of fluids--Determination of resistance to rapid crack propagation (RCP)--Small-scale steady-state test(S4 test)
GB/T 19466.6-2009 Plastics.Differential scanning calorimetry(DSC).Part 6:Determination of oxidation induction time(isothermal OIT) and oxidation induction temperature (dynamic OIT)
GB/T 19807-2005 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting
GB/T 19808-2005 Plastics pipes and fittings.Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
GB/T 19809-2005 Plastics pipes and fittings.Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion
GB/T 19810-2005 Polyethylene(PE)pipe and fittings.Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
GB/T 321 Preferred numbers-Series of preferred numbers
GB/T 3681-2011 Plastics. Methods of exposure to direct weathering,to weathering using glass-filtered daylight,and to intensified weathering by daylight using Fresnel mirrors
GB/T 3682.1 Plastics—Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics—Part 1:Standard method*, 2018-03-15 Update
GB/T 6111-2003 Thermoplastics pipes for the conveyance of fluids-Resistance to internal pressure--Test method
GB/T 8804.1-2003 Thermoplastic pipes--Determination of tensile properties--Part 1: General test method
GB/T 8804.3-2003 Thermoplastic pipes--Determination of tensile properties--Part 3: Polyolefin pipes
GB/T 9345.1-2008 Plastics.Determination of ash.Part1:General methods
SH/T 1770-2010 Plastics.Determination of water content for polyethylene
GB/T 13663.1-2017 history
2017GB/T 13663.1-2017 Polyethylene(PE) piping systems for water supply.Part 1:General