13.340.99 其他防护设备 标准查询与下载

KS G ISO 10333-2-2010(2021) 个人防坠落系统第2部分:系索和能量吸收器

Personal fall-arrest systems－Part 2：Lanyards and energy absorbers

KS G ISO 10333-3-2010(2021) 个人防坠落系统第3部分:自缩救生索

Personal fall-arrest systems－Part 3：Self-retracting lifelines

KS G ISO 14567-2010(2021) 高处坠落个人防护设备单点锚固装置

Personal protective equipment for protection against falls from a height－Single-point anchor devices

KS G ISO 14567:2010 防止从高处坠落的个人防护装置.单点锚定设备

이 표준은 추락 방지, 작업 포지셔닝(work positioning) 및 이동제한(trav

Personal protective equipment for protection against falls from a height－Single-point anchor devices

GA 872-2010 防爆球

本标准规定了防爆球的术语和定义、产品命名、技术要求、试验方法、检验规则、包装、运输及贮存。 本标准适用于防爆球。

Explosion suppression container

GA 871-2010 防爆罐

本标准规定了防爆罐的术语和定义、分类与命名、技术要求、试验方法、检验规则、包装、运输及贮存。 本标准适用于防爆罐。

Bomb blast suppression bin

ASTM C1695-10(2015) 热加工用可移去与可重复使用的柔性绝缘卷材的制造规格

1.1 This specification covers the minimum requirements for materials and fabrication of flexible removable and reusable blanket insulation for hot service, from above ambient temperatures to 1000°F (538°C). 1.2 This specification separately addresses both outdoor and indoor applications. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Fabrication of Flexible Removable and Reusable Blanket Insulation for Hot Service

CAN/CSA-Z262.6-2009(C2014) 具有面部特征的头模规范

Domaine d'application 1.1 Cette norme établit les exigences relatives aux dimensions et aux matériaux des fausses têtes présentant des traits du visage et devant servir à la mise à l'essai de l'équipement de protection des yeux et du visage complet, en particulier la protection contre les chocs. 1.2 Dans les normes CSA, le terme «doit» indique une exigence, c'est-à-dire une prescription que l'utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu'il est conseillé mais non obligatoire de faire ; et «peut», une possibilité ou un conseil. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d'informatives (facultatives) pour en préciser l'application.

Specifications for headforms with facial features

CAN/CSA-Z262.6-2009(R2014) 面部特征头模规范

Scope 1.1 This Standard specifies the dimensional and material requirements for facially featured headforms to be used in the testing of full-face protection and eye protection equipment, especially impact protection testing. 1.2 In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative materal. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Specifications for facially featured headforms

ASTM F2676-09 防止电弧危害的电弧保护毯防护性能确定的标准试验方法

This test method determines the effectiveness of arc protective blankets in suprressing the combined effects of an arc flash and arc blast. The arc exposure energy is produced from controlled phase-to-ground arc fault. The resulting arc flash and blast energy are intentionally directed onto the test specimen to simulate worst case conditions. Test results will describe the maximum arc current and product of arc current and cycles at which test specimens block the energy without breakopen, ability to self-extinguish afterflaming, afterflame time and the detection of mechanical attachment failures during testing. Mechanical attachment failure and afterflame time are obtained from visual observations and video recording after each arc exposure. This test method maintains the arc protective blanket in a vertical position and does not involve movement except that resulting from the arc exposure. In this test method, test specimens are exposed at three arc current levels to determine the test specimen’s performance. Note 28212;In experimental testing, some blankets increase in protection (in value of kA*cycles to cause breakopen) as the arc current increases and some decrease as shown in Fig. 1. This test method is designed to recognize this behavior and to specify testing over the range of arc current levels including lower levels of 5 kA or 10 kA, or both. This test method specifies a standard set of exposure conditions. Different exposure conditions may produce different results. Note 38212;In addition to the standard set of exposure conditions, it is permitted to test using other conditions representative of the expected hazard, reported all non-standard test conditions that are used. FIG. 1 Example of Performance Trend for Different Blankets1.1 This test method is used to evaluate the ability of the arc protective blankets to withstand the effects of arc flash and arc blast in a configuration in which the blanket is hung or anchored near energized equipment. Specifically, this test method is used to determine the arc protective blanket’s (1) resistance to breakopen, (2) mechanical strength, and (3) ability to self-extinguish flames following a controlled arc exposure. 1.2 This method is used to determine the performance of arc protective blankets in terms of: maximum arc current level expressed in kA and BTP (BTP) expressed as the product of arc current in kA and arc duration in number of cycles to cause breakopen (kA*cycles). Cycles are on the basis of 60 Hz. 1.3 Blanket test specimens used in this test method are test size blankets of 152 ± 5 cm (60 ± 2 in.) by 122 ± 5 cm (48 ± 2 in.). The test specimen size is for testing purposes only. Commercially available arc protective blankets either larger or smaller than the test specimen size are covered by this standard. 1.4 The arc protective blankets described in this test method are made of flame-resistant materials and are available in varying sizes and configurations based on the application. 1.5 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to incident thermal (convective and radiant) and pressure energies generated by an electric arc under controlled laboratory conditions. 1......

Standard Test Method for Determining the Protective Performance of an Arc Protective Blanket for Electric Arc Hazards

SANS 50365:2008 防高空坠落的人员防护装置.使用、保养、定期检查、修理指示、标记和包装说明的一般要求

States the general requirements for instructions for use and for marking of equipment for protection against falls from heights.

Personal protective equipment against falls from a height - General requirements for instructions for use, maintenance, periodic examination, repair, marking and packaging

SANS 50362:2008 防高空坠落的人员防护装置.连接器

Specifies the requirements, test methods, instructions for use and marking for connectors.

Personal protective equipment against falls from a height - Connectors

GA 422-2008 防暴盾牌

本标准规定了防暴盾牌的术语和定义、分类与代号、技术要求、试验方法、检验规则、包装、运输和贮存。 本标准适用于防暴盾牌。

Anti-riot shield

SANS 50358:2008 用于工作定位及防高空坠落的个人防护装置.工作定位及约束带及工作定位系索

Applies to belts and lanyards intended for the purpose of work positioning or restraint. Specifies the requirements, testing, marking and information supplied by the manufacturer.

Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards

GA 420-2008 警用防暴服

本标准规定了警用防暴服（以下简称防暴服）的术语和定义、分类及命名、技术要求、试验方法、检验规则和标志、包装、运输及贮存。 本标准适用于警用防暴服。

Anti-riot suit for police

GA 68-2008 警用防刺服

本标准规定了警用防刺服（以下简称防刺服）产品的术语和定义、分类和命名、技术要求、试验方法、检验规则、包装、运输及贮存。 本标准适用于警用防刺服。

Stab resistance body armor for police

GOST R EN 813-2008 职业安全标准体系.防止高处掉落用个人防护装置.坐式安全带.一般技术要求.测试方法

Occupational safety standards system. Personal protective equipment against falls from a height. Sit harnesses. General technical requirements. Test methods

GOST R EN 360-2008 职业安全标准体系.防止高处掉落用个人防护装置.伸缩式防坠装置.一般技术要求.测试方法

Occupational safety standards system. Personal protective equipment against falls from a height. Retractable type fall arresters. General technical requirements. Test methods

GOST R EN 358-2008 职业安全标准体系.防止高处掉落用个人防护装置.工作定位及安全带或安全索.一般技术要求.测试方法

Occupational safety standards system. Personal protective equipment against falls from a height. Belts and lanyards for work positioning and restraint. General technical requirements. Test methods

GOST R EN 355-2008 职业安全标准体系.防止高处掉落用个人防护装置.减能器.一般技术要求.测试方法

Occupational safety standards system. Personal protective equipment against falls from a height. Energy absorbers. General technical requirements. Test methods