21.060.01 紧固件综合 标准查询与下载

T/SZJGJ 001-2024 《十字型紧固件》

4.4 机械和物理性能 4.4.1 屈服强度、抗拉强度、硬度、破坏扭矩 机螺丝应符合GB/T 3098.1或GB/T 3098.6的规定。自攻螺钉符合GB/T 3098.5或GB/T 3098.21的规定。 4.4.2 螺纹精度 机螺纹精度应符合GB/T 197中要求。自攻螺纹应符合GB/T 5280中要求。 4.5表面缺陷 应符合 GB/T 5779.1的要求。 4.6耐腐蚀性 产品经中性盐雾试验按部件≥2h，无腐蚀现象。 5 试验方法 5.1外观质量 5.2尺寸公差 按JB/T 9151.1规定的方法进行检验。 5.3机械性能 5.3.1 屈服强度 机螺丝按GB/T 3098.1或GB/T 3098.6规定的方法进行。  5.3.2 抗拉强度 按GB/T 228.1和GB/T 3098.1的规定抗拉强度(Rm)应在L≥2.5d的紧固件上进行测量。 未旋合螺纹的长度应大于或等于2.5d。 5.3.3 硬度 按照GB/T 230.1的规定进行。 5.3.4 破坏扭矩 按GB/T 3098.13规定的方法进行。

Cross type fastener

ASTM A193/A193M-24 高温或高压服务及其他特殊用途应用的合金钢和不锈钢螺栓标准规范

Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

ASTM A540/A540M-24 特殊应用合金钢螺栓连接标准规范

Standard Specification for Alloy-Steel Bolting for Special Applications

ASTM A320/A320M-24 低温用合金钢和不锈钢螺栓连接标准规范

Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

T/CZII 002-2024 包装用锁扣产品

为规范工业包装用锁扣产品生产技术要求，针对包装用锁扣产品进行规定，通过对包装用锁扣产品生产工艺说明将包装用锁扣产品质量进行提升，助力推动社会绿色可持续发展，特制定本标准。

Lock products for packaging

ASTM F959/F959M-17a(2023) 英制和公制结构紧固件用可压缩垫圈型直接张力指示器标准规范

Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series

ASTM F3043-23 最小抗拉强度为200 ksi的热处理合金钢“扭转”型张力控制结构螺栓/螺母/垫圈组件的标准规范

Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength

ASTM F2437/F2437M-17(2023) 带帽螺钉、螺栓、锚固件和双头螺栓用碳素钢和合金钢可压缩垫圈型直接张力指示器的标准规范

Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs

ASTM G198-17(2023) 与处理过的木材接触的传动紧固件相对腐蚀性能测定的标准试验方法

Standard Test Method for Determining the Relative Corrosion Performance of Driven Fasteners in Contact with Treated Wood

ASTM F3111-23 最小抗拉强度为200 ksi的热处理合金钢重型六角结构螺栓/螺母/垫圈组件的标准规范

Standard Specification for Heavy Hex Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength

ASTM F2282-23 机械紧固件用碳素钢和合金钢线材、棒材和棒材的质量保证要求标准规范

Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners

T/CZII 016-2023 高压夹套法兰技术条件

为规范工业产品生产要求，针对高压夹套法兰类产品进行规定，通过对此类的技术要求、试验方法、检验规则、标志、随机附带文件、包装、运输进行规定，以提高高压夹套法兰性能，助力推动社会绿色可持续发展，特制定本标准。

High pressure jacket flange technical conditions

ASTM A962/A962M-23a 用于从低温到蠕变范围的任何温度下使用的螺栓连接的通用要求的标准规范

Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

ASTM A962/A962M-23 用于从低温到蠕变范围的任何温度下使用的螺栓连接的通用要求的标准规范

Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

ASTM D5649-15(2023) 螺纹紧固件上使用的粘合剂扭矩强度的标准试验方法

1.1 This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Torque Strength of Adhesives Used on Threaded Fasteners

ASTM A193/A193M-23 高温或高压设备和其他特殊用途用合金钢和不锈钢螺栓的标准规范

1.1 This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting. Bars and wire shall be hot-wrought and may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be carbide solution treated or carbide solution treated and strain-hardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood. 1.2 Several grades are covered, including ferritic steels and austenitic stainless steels designated B5, B8, and so forth. Selection will depend upon design, service conditions, mechanical properties, and high temperature characteristics. 1.3 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. NOTE 1—The committee formulating this specification has included several steel types that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent. NOTE 2—For grades of alloy-steel bolting suitable for use at the lower range of high temperature applications, reference should be made to Specification A354. NOTE 3—For grades of alloy-steel bolting suitable for use in low temperature applications, reference should be made to Specification A320/A320M. 1.4 Nuts for use with bolting are covered in Section 13. 1.5 Supplementary Requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified in the purchase order or contract. 1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

ASTM A320/A320M-22a 低温设备用合金钢和不锈钢螺栓的标准规范

1.1 This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for low-temperature service. See Specification A962/A962M for the definition of bolting. The bars shall be hot-wrought and may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strainhardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood. 1.2 Several grades are covered, including both ferritic and austenitic steels designated L7, B8, etc. Selection will depend on design, service conditions, mechanical properties, and low-temperature characteristics. The mechanical requirements of Table 1 indicate the diameters for which the minimum mechanical properties apply to the various grades and classes, and Table 2 stipulates the requirements for Charpy impact energy absorption. The manufacturer should determine that the material can conform to these requirements before parts are manufactured. For example, when Grade L43 is specified to meet the Table 2 impact energy values at −150 °F [−101 °C], additional restrictions (such as procuring a steel with lower P and S contents than might normally be supplied) in the chemical composition for AISI 4340 are likely to be required. NOTE 1—The committee formulating this specification has included several grades of material that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent. Users should note that hardenability of some of the grades mentioned may restrict the maximum size at which the required mechanical properties are obtainable. 1.3 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.4 Nuts for use with bolting are covered in Section 10 and the nut material shall be impact tested. 1.5 Supplementary Requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified in the purchase order or contract. 1.6 This specification is expressed in both inch-pound units and SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI) units, the inch-pound units shall apply. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

ASTM A193/A193M-22a 高温或高压设备和其他特殊用途用合金钢和不锈钢螺栓的标准规范

1.1 This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting. Bars and wire shall be hot-wrought and may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be carbide solution treated or carbide solution treated and strain-hardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood. 1.2 Several grades are covered, including ferritic steels and austenitic stainless steels designated B5, B8, and so forth. Selection will depend upon design, service conditions, mechanical properties, and high temperature characteristics. 1.3 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. NOTE 1—The committee formulating this specification has included several steel types that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent. NOTE 2—For grades of alloy-steel bolting suitable for use at the lower range of high temperature applications, reference should be made to Specification A354. NOTE 3—For grades of alloy-steel bolting suitable for use in low temperature applications, reference should be made to Specification A320/A320M. 1.4 Nuts for use with bolting are covered in Section 13. 1.5 Supplementary Requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified in the purchase order or contract. 1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

ASTM A193/A193M-22 高温或高压服务和其他特殊用途用合金钢和不锈钢螺栓

1.1 This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting. Bars and wire shall be hot-wrought and may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be carbide solution treated or carbide solution treated and strain-hardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood. 1.2 Several grades are covered, including ferritic steels and austenitic stainless steels designated B5, B8, and so forth. Selection will depend upon design, service conditions, mechanical properties, and high temperature characteristics. 1.3 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. NOTE 1—The committee formulating this specification has included several steel types that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent. NOTE 2—For grades of alloy-steel bolting suitable for use at the lower range of high temperature applications, reference should be made to Specification A354. NOTE 3—For grades of alloy-steel bolting suitable for use in low temperature applications, reference should be made to Specification A320/A320M. 1.4 Nuts for use with bolting are covered in Section 13. 1.5 Supplementary Requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified in the purchase order or contract. 1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

BS EN ISO 3506-6:2022 紧固件 耐腐蚀不锈钢紧固件机械性能 紧固件不锈钢和镍合金选用通则

This document specifies general rules and provides technical information on stainless steels and their properties, which are relevant when using other parts of the ISO 3506 series. It includes specifications for corrosion-resistant stainless steels and nickel alloys, which are suitable for the manufacture of fasteners. It applies to austenitic, martensitic, ferritic and duplex (austenitic-ferritic) stainless steel grades and nickel alloys for fasteners, and is intended to be used together with the relevant parts of the ISO 3506 series. Common designations of stainless steels and nickel alloys used for fasteners are given in Annex A.

Fasteners. Mechanical properties of corrosion-resistant stainless steel fasteners - General rules for the selection of stainless steels and nickel alloys for fasteners