23.040.10 铁管和钢管 标准查询与下载

CSA B70.1-2023 维护孔和集水槽的框架和盖子

1 Scope 1.1 General This Standard applies to frames and covers for maintenance holes and catchbasins. 1.2 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Frames and covers for maintenance holes and catchbasins

ASTM A498/A498M-17(2023) 带整体翅片的无缝和焊接碳钢热交换器管

1.1 This specification describes seamless or welded lowcarbon steel tubes on which the external or internal surface, or both, have been modified by a cold forming process to produce an integral increased surface area for improved heat transfer. The tubes are used in tubular heat exchangers, surface condensers, evaporators, superheaters, and similar heattransfer apparatus in outside diameters up to 2 in. [50 mm], inclusive. 1.2 Units—This specification is expressed in both inchpound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins

T/CFA 020102024-2023 非开挖施工用球墨铸铁管 第 1 部分：顶管法用

本文件规定了顶管法用非开挖施工用球墨铸铁管（以下简称顶管）的术语和定义，顶管结构、接口 尺寸、外形及允许偏差，技术要求，试验方法，检验规则，标志、包装、存放、吊装、运输等。 本文件适用于包含有承口、插口,一般以内部和外部涂覆状态交货的,尺寸范围为公称直径DN 250～ DN 2600 的球墨铸铁顶管，适用范围如下： ——采用顶管法于地下非开挖施工； ——在无压、有条件下运行； ——分流输送或合流输送饮用水、消防用水、造雪用水、灌溉用水、水电站用水、雨水、污水、某些类型的工业废水

Ductile iron pipes for trenchless application— Part 1：used for pipe jacking method

KS D 4317-2022 球墨铸铁管和管件内部的环氧粉末涂层

Epoxy-powder coating on the inside of ductile iron pipes and fittings

KS D 4308-2022 球墨铸铁配件

Ductile iron fittings

KS D 3607-2022 粉末熔接聚乙烯涂层钢管和管件

Polyethylene coated steel pipes and fittings by powder fusion

DB3715/T 28-2022 钢管生产企业安全生产基本规范

本文件适用于聊城市钢管生产企业的安全生产工作。

Basic norms for safe production of steel pipe production enterprises

ASTM A269/A269M-22 通用无缝和焊接奥氏体不锈钢管标准规范

1.1 This specification covers grades of nominal-wallthickness, stainless steel tubing for general corrosion-resisting and lowor high-temperature service, as designated in Table 1. 1.2 The tubing sizes and thicknesses usually furnished to this specification are 1⁄4 in. [6.4 mm] in inside diameter and larger and 0.020 in. [0.51 mm] in nominal wall-thickness and heavier. 1.3 Mechanical property requirements do not apply to tubing smaller than 1⁄8 in. [3.2 mm] in inside diameter or 0.015 in. [0.38 mm] in thickness. NOTE 1—Additional testing requirements may apply for use in ASME B31.3 applications. 1.4 Optional supplementary requirements are provided and, when one or more of these are desired, each shall be so stated in the order. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service

ASTM F1083-18(2022) 围栏结构用热浸镀锌（镀锌）焊接钢管标准规范

1.1 This specification covers hot-dipped galvanized welded steel pipe in sizes ranging from 1.315–8.625 in. (33.4 –219.1 mm) outside diameter (OD) inclusive, with nominal (average) wall thickness as given in Table 1 and Table 2. Pipe having other dimensions (Note 2) may be furnished provided such pipe complies with all other requirements of this specification. Pipe ordered under this specification is intended for use as a structural support for fencing in accordance with Specification F1043, Group 1A. NOTE 1—Outside diameter size is designated in that fence fittings are designed to securely fit on the outside of the pipe framework. NOTE 2—A comprehensive listing of standardized pipe dimensions is contained in ANSI B 36.10. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures

T/CFA 03033-2022 质量分级及“领跑者”评价要求 非开挖管道施工用球墨铸铁顶管

本文件规定了非开挖管道施工用球墨铸铁顶管（以下简称顶管）质量分级及“领跑者”评价要求的术语和定义、评价指标体系和评价方法。

Assessment requirements for forerunner standard - Ductile iron jacking pipe for trenchless pipeling construction

ASTM A376/A376M-22 高温用无缝奥氏体钢管标准规范

1.1 This specification2 covers seamless austenitic steel pipe intended for high-temperature service. Among the grades covered are H grades and nitrogen grades that are specifically intended for high-temperature service. NOTE 1—This specification was originally developed for use for piping in the central stations of electric-power generating thermal plants. However, its use is not restricted to such applications and it may be used in other applications for which the attributes of the materials, as defined by this specification, are appropriate. 1.2 Optional supplementary requirements (S1 through S10) are provided. These supplementary requirements specify additional tests that will be made only when stated in the order, together with the number of such tests required. 1.3 Grades TP321 and TP321H have lower strength requirements for nominal wall thicknesses greater than 3⁄8 in. [9.5 mm]. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. NOTE 2—The dimensionless designators NPS (nominal pipe size) and DN (Diametre Nominel) have been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Service

ASTM A312/A312M-22a 无缝、焊接和重冷加工奥氏体不锈钢管标准规范

1.1 This specification2 covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service. 1.2 Grades TP304H, TP309H, TP309HCb, TP310H, TP310HCb, TP316H, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP309Cb, TP309S, TP310Cb, TP310S, TP316, TP321, TP347, and TP348, and are intended for service at temperatures where creep and stress rupture properties are important. 1.3 Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, it is permitted to specify in the order one or more of these supplementary requirements. 1.4 Table X1.1 lists the standardized dimensions of welded and seamless stainless steel pipe as shown in ASME B36.19. These dimensions are also applicable to heavily cold worked pipe. Pipe having other dimensions is permitted to be ordered and furnished provided such pipe complies with all other requirements of this specification. 1.5 Grades TP321 and TP321H have lower strength requirements for pipe manufactured by the seamless process in nominal wall thicknesses greater than 3⁄8 in. [9.5 mm]. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

ASTM A213/A213M-22a 无缝铁素体和奥氏体合金钢锅炉、过热器和热交换器管标准规范

1.1 This specification2 covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2. 1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. 1.3 The tubing sizes and thicknesses usually furnished to this specification are 1⁄8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

T/CFA 03032-2022 质量分级及“领跑者”评价要求 建筑排水柔性接口铸铁管、管件及附件

本文件规定了建筑排水柔性接口铸铁管、管件及附件质量及企业标准水平评价的术语和定义、评价指标体系和评价方法。

Assessment requirements for quality grading and forerunner - Cast iron pipes, fittings and accessories with flexible interface for building

ASTM A335/A335M-22 高温用无缝铁素体合金钢管

1.1 This specification2 covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for hightemperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Selection will depend upon design, service conditions, mechanical properties, and high-temperature characteristics. 1.2 Several grades of ferritic steels (see Note 1) are covered. Their compositions are given in Table 1. NOTE 1—Ferritic steels in this specification are defined as lowand intermediate-alloy steels containing up to and including 10 % chromium. 1.3 Supplementary requirements (S1 to S8) of an optional nature are provided. Supplementary requirements S1 through S6 call for additional tests to be made, and when desired, shall be so stated in the order together with the number of such tests required. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. NOTE 2—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

22/30434600 DC BS ISO 10803.球墨铸铁管的设计方法

BS ISO 10803. Design method for ductile iron pipes

GSO ISO 21051:2022 球墨铸铁管道系统施工与安装

This document specifies the recommended practices and requirements for the installation of buried and above-ground ductile iron pipeline system conforming to ISO 2531, ISO 7186 and ISO 16631. The recommended practices in this document are intended to provide the practical advices based on the best methods of construction and installation of ductile iron pipeline system including pipes, fittings, valves and accessories.

Construction and installation of ductile iron pipeline system

GSO ISO 16134:2022 球墨铸铁管道的抗震、抗沉降设计

This document specifies the design of earthquake-resistant and subsidence-resistant ductile iron pipelines suitable for use in areas where seismic activity and land subsidence can be expected. It provides a means of determining and checking the resistance of buried pipelines and gives example calculations. It is applicable to ductile iron pipes and fittings with joints as specified in ISO 2531, ISO 7186 and ISO 16631 that have expansion/contraction and deflection capabilities, used in pipelines buried underground. NOTE Subsidence is not the effects of an earthquake or a sinkhole.

Earthquake-resistant and subsidence-resistant design of ductile iron pipelines

ASTM A716-18(2022) 球墨铸铁管

1.1 This specification covers 14 to 64 in. ductile iron culvert pipe, centrifugally cast. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods portions, Sections 6 and 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ductile Iron Culvert Pipe

ASTM B690-22 铁镍铬钼合金无缝管

1.1 This specification covers iron-nickel-chromiummolybdenum alloy (UNS N08367)2 cold-finished annealed or hot-finished annealed seamless pipe and tube intended for use in special corrosive service and for heat-resisting applications. 1.2 Pipe and tube shall be supplied in the solution heat treated and descaled condition. When bright annealing is used, descaling is not necessary. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy Seamless Pipe and Tube