23.040.10 铁管和钢管 标准查询与下载

ASTM A861-04(2023) 高硅铁管和配件标准规范

1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both aboveand below-grade construction. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain-end design. 1.4 Pipe and pipe fittings shall be of the sizes specified in Table 1 and Table 2 and Figs. 1–71 or other sizes that shall be permitted to conform to the requirements given herein. 1.4.1 Pipe: 1.4.1.1 No-Hub (MJ) (Fig. 1): Size (in.) Length (ft) 11⁄2 7 2 7 3 7 4 7 1.4.1.2 Hub/Plain End (Fig. 35): Size (in.) Length (ft) 2 7 3 7 4 7 6 7 8 7 10 5 12 5 15 5 1.4.2 Fitting (No-Hub) (MJ): Figs. Quarter Bends 2 Sixth Bends 3 Return Bends 4 Double-Branch Quarter Bend 5 Eighth Bends 6 Sixteenth Bends 7 Long-Sweep Quarter Bends 8 Sanitary Y Branches 9 Double-Branch Sanitary Y 10 Sanitary Combination Y and 1⁄8 Bend 11 Double-Branch Sanitary Combination Y and 1⁄8 Bend 12 Sanitary T Branches 13 Double Branch Sanitary T 14 Sanitary Running Traps 15 Sanitary P Traps 16 Swivel Trap P-Style, Short 17 Swivel Trap P-Style, Long 18 Swivel Trap S-Style, Long 19 Centrifugal Drum Trap P Swivel Type 20 Centrifugal Drum Trap S Swivel Type 21 Combination Cleanout and Test Tees 22 Coupling 23 Pipe Plugs 24 Cleanout Plugs 25 No-Hub (MJ) Adapter 26 Reducers-Increasers 27 Sink Outlet 28 Sink Overflows 29 Threaded Adapters 30 Trap Cleanout Details 31 No-Hub (MJ) Adapter 32 (MJ) (No-Hub) to Lead Adapter 33 Floor Drains 34 1.4.3 Fitting (Hub/Plain End): Figs. Hub Plain-End Pipe 35 Straight Tees 36 Sanitary T Branches 37 Sanitary Y Branches 38 Double-Branch Sanitary Tee 39 Double-Branch Sanitary Y 40 Double-Branch Sanitary Combination Y and 1⁄8 Bend (T-Y) 41 Short-Sweep Quarter Bends 42 Long-Sweep Quarter Bends 43 Sanitary Combination Y and 1⁄8 Bend (T-Y) 44 Quarter Bends 45 1 This specification is under the jurisdiction of ASTM Committee A04 on Iron Castings and is the direct responsibility of Subcommittee A04.12 on Pipes and Tubes. Current edition approved May 1, 2023. Published May 2023. Originally approved in 1986. Last previous edition approved in 2017 as A861 – 04 (2017). DOI: 10.1520/A0861-04R23. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 Sixth Bends 46 Eighth Bends 47 Sixteenth Bends 48 Sanitary Increasers 49 Hub Strainers 50 Sanitary Reducers 51 Double Hubs 52 Pipe Plugs 53 Cleanout Plugs 54 Adapter – Plain end to Split Flange 55 Adapter – Hub to Split Flange 56 Combination Cleanout and Test Tees 57 Insertable Joints 58 Backwater Valves 59 Sanitary P Traps 60 Sanitary S Traps 61 Sanitary Running Traps 62 Floor Drains 63, 64, 65 Floor Drains 66 Floor Drains/Installation – Funnel Attachment 67, 68 Overflow 69 Sink Outlet 70 Detailed Cross Section of Cleanout 71 Chemical Composition Table 3 Transverse Bend Test Minimum Requirements Table S1.1 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for High-Silicon Iron Pipe and Fittings

ASTM A213/A213M-23 无缝铁素体和奥氏体合金钢锅炉、过热器和热交换器管标准规范

1.1 This specification2 covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2. 1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. 1.3 The tubing sizes and thicknesses usually furnished to this specification are 1⁄8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

ASTM A270/A270M-23 无缝和焊接奥氏体和铁素体/奥氏体不锈钢卫生卡套管标准规范

1.1 This specification covers grades of seamless, welded, and heavily cold worked welded austenitic and ferritic/ austenitic stainless steel sanitary tubing intended for use in the dairy and food industry and having special surface finishes. Pharmaceutical quality may be requested, as a supplementary requirement. 1.2 This specification covers tubes in sizes up to and including 12 in. [300 mm] in outside diameter. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 Optional supplementary requirements are provided, and when one or more of these are desired, each shall be so stated in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Austenitic and Ferritic/Austenitic Stainless Steel Sanitary Tubing

ASTM A335/A335M-23 高温用无缝铁素体合金钢管标准规范

1.1 This specification2 covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for hightemperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Selection will depend upon design, service conditions, mechanical properties, and high-temperature characteristics. 1.2 Several grades of ferritic steels (see Note 1) are covered. Their compositions are given in Table 1. NOTE 1—Ferritic steels in this specification are defined as lowand intermediate-alloy steels containing up to and including 10 % chromium. 1.3 Supplementary requirements (S1 to S9) of an optional nature are provided. Supplementary requirements S1 through S6 call for additional tests to be made, and when desired, shall be so stated in the order together with the number of such tests required as applicable. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. NOTE 2—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

BS ISO 24131-1:2023 球墨铸铁管采用聚合物衬里进行内部保护 要求和测试方法 聚氨酯衬里

1   Scope This document specifies the requirements and test methods applicable to factory applied internal polyurethane lining for ductile iron pipes according to ISO 2531, ISO 7186 and ISO 16631. It covers internal linings for use in the conveyance of raw water, potable water and sewage water for operating temperature up to 50 °C.

Internal protection by polymeric lining for ductile iron pipes. Requirements and test methods - Polyurethane lining

BS ISO 24131-2:2023 球墨铸铁管采用聚合物衬里进行内部保护 要求和测试方法 环氧衬里

1   Scope This document specifies the requirements and test methods applicable to factory applied internal epoxy lining for ductile iron pipes according to ISO 2531, ISO 7186 and ISO 16631. It covers internal linings for use in the conveyance of raw water, potable water and sewage water for operating temperature up to 50 °C.

Internal protection by polymeric lining for ductile iron pipes. Requirements and test methods - Epoxy lining

T/HEBQIA 150-2023 机动车过滤器用滤筒

本文件规定了机动车过滤器用滤筒的产品尺寸图样及结构、要求、试验方法、检验规则、标志、包装、运输、贮存。

Cartridges for Motor Vehicle Filters

23/30466158 DC BS EN 17970 球墨铸铁管 用于球墨铸铁管道系统的快插接头 抵抗根部入侵 要求及测试方法

BS EN 17970. Ductile iron pipes. Push-in joints for ductile iron pipe systems. Resistance against root intrusion. Requirements and test methods

ISO 24131-1:2023 球墨铸铁管用聚合物衬里的内部保护.要求和试验方法.第1部分：聚氨酯衬里

This document specifies the requirements and test methods applicable to factory applied internal polyurethane lining for ductile iron pipes according to ISO 2531, ISO 7186 and ISO 16631. It covers internal linings for use in the conveyance of raw water, potable water and sewage water for operating temperature up to 50 °C.

Internal protection by polymeric lining for ductile iron pipes — Requirements and test methods — Part 1: Polyurethane lining

ISO 24131-2:2023 球墨铸铁管用聚合物衬里的内部保护.要求和试验方法.第2部分：环氧衬里

This document specifies the requirements and test methods applicable to factory applied internal epoxy lining for ductile iron pipes according to ISO 2531, ISO 7186 and ISO 16631. It covers internal linings for use in the conveyance of raw water, potable water and sewage water for operating temperature up to 50 °C.

Internal protection by polymeric lining for ductile iron pipes — Requirements and test methods — Part 2: Epoxy lining

ASTM A498/A498M-17(2023) 带整体翅片的无缝和焊接碳钢热交换器管

1.1 This specification describes seamless or welded lowcarbon steel tubes on which the external or internal surface, or both, have been modified by a cold forming process to produce an integral increased surface area for improved heat transfer. The tubes are used in tubular heat exchangers, surface condensers, evaporators, superheaters, and similar heattransfer apparatus in outside diameters up to 2 in. [50 mm], inclusive. 1.2 Units—This specification is expressed in both inchpound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins

T/CFA 020102024-2023 非开挖施工用球墨铸铁管 第 1 部分：顶管法用

本文件规定了顶管法用非开挖施工用球墨铸铁管（以下简称顶管）的术语和定义，顶管结构、接口 尺寸、外形及允许偏差，技术要求，试验方法，检验规则，标志、包装、存放、吊装、运输等。 本文件适用于包含有承口、插口,一般以内部和外部涂覆状态交货的,尺寸范围为公称直径DN 250～ DN 2600 的球墨铸铁顶管，适用范围如下： ——采用顶管法于地下非开挖施工； ——在无压、有条件下运行； ——分流输送或合流输送饮用水、消防用水、造雪用水、灌溉用水、水电站用水、雨水、污水、某些类型的工业废水

Ductile iron pipes for trenchless application— Part 1：used for pipe jacking method

T/CFA 020102029-2023 非开挖施工用球墨铸铁管 第2 部分：水平定向钻法用

本文件规定了给水排水管道水平定向钻法施工用球墨铸铁管（简称拖拉管）及其接口的术语和定义，结构、接口、长度及允许偏差，技术要求，试验方法，出厂检验，标志、包装、存放、吊装、运输、安装和质量证明书。 本文件适用于公称规格为DN 100～DN 1200、包含有承口、插口及内部和外部涂覆状态交货的离心球墨铸铁管；适用于有压或无压输送各种不同用途的流体（饮用水、消防用水、灌溉用水、水电站用水、原水、处理过的水、回用水等），及温度为0℃～50℃的地下非开挖铺设施工用的球墨铸铁拖拉管及附件。

Ductile iron pipes for trenchless construction— part 2 : used for horizontal directional drilling method

CSA B70.1-2023 维护孔和集水槽的框架和盖子

1 Scope 1.1 General This Standard applies to frames and covers for maintenance holes and catchbasins. 1.2 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Frames and covers for maintenance holes and catchbasins

ASTM A249/A249M-18a(2023) 焊接奥氏体钢锅炉、过热器、换热器和冷凝器管的标准规范

1.1 This specification2 covers nominal-wall-thickness welded tubes and heavily cold worked welded tubes made from the austenitic steels listed in Table 1, with various grades intended for such use as boiler, superheater, heat exchanger, or condenser tubes. 1.2 Grades TP304H, TP309H, TP309HCb, TP310H, TP310HCb, TP316H, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP309S, TP309Cb, TP310S, TP310Cb, TP316, TP321, TP347, and TP348, and are intended for high-temperature service such as for superheaters and reheaters. 1.3 The tubing sizes and thicknesses usually furnished to this specification are 1⁄8 in. [3.2 mm] in inside diameter to 12 in. [304.8 mm] in outside diameter and 0.015 to 0.320 in. [0.4 to 8.1 mm], inclusive, in wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. 1.4 Mechanical property requirements do not apply to tubing smaller than 1⁄8 in. [3.2 mm] in inside diameter or 0.015 in. [0.4 mm] in thickness. 1.5 Optional supplementary requirements are provided and, when one or more of these are desired, each shall be so stated in the order. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.7 The following safety hazards caveat pertains only to the test method described in the Supplementary Requirements of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in Supplementary Requirement S7, Note S7.1. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes

KS D 3607-2022 粉末熔接聚乙烯涂层钢管和管件

Polyethylene coated steel pipes and fittings by powder fusion

KS D 4308-2022 球墨铸铁配件

Ductile iron fittings

KS D 4317-2022 球墨铸铁管和管件内部的环氧粉末涂层

Epoxy-powder coating on the inside of ductile iron pipes and fittings

DB3715/T 28-2022 钢管生产企业安全生产基本规范

本文件适用于聊城市钢管生产企业的安全生产工作。

Basic norms for safe production of steel pipe production enterprises

ASTM A213/A213M-22a 无缝铁素体和奥氏体合金钢锅炉、过热器和热交换器管标准规范

1.1 This specification2 covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2. 1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. 1.3 The tubing sizes and thicknesses usually furnished to this specification are 1⁄8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes