23.040.10 铁管和钢管 标准查询与下载

ASTM E213-22 金属管和管子的超声波检验的标准实施规程

1.1 This practice2 covers a procedure for detecting discontinuities in metal pipe and tubing during a volumetric examination using ultrasonic methods. Specific techniques of the ultrasonic method to which this practice applies include pulse-reflection techniques, both contact and non-contact (for example, as described in Guide E1774 and Practice E1816), and angle beam immersion techniques, both conventional and phased array. Artificial reflectors consisting of longitudinal, and, when specified by the using party or parties, transverse reference notches placed on the surfaces of a reference standard are employed as the primary means of standardizing the ultrasonic system. 1.2 This practice is intended for use with tubular products having outside diameters approximately 1⁄2 in. (12.7 mm) and larger, provided that the examination parameters comply with and satisfy the requirements of Section 11. These procedures have been successful with smaller sizes. These may be specified upon contractual agreement between the using parties. These procedures are intended to ensure that proper beam angles and beam shapes are used to provide full volume coverage of pipes and tubes, including those with low ratios of outside diameter-to-wall thickness, and to avoid spurious signal responses when examining small-diameter, thin-wall tubes. 1.3 The procedure in Annex A1 is applicable to pipe and tubing used in nuclear and other special and safety applications. The procedure in Annex A2 may be used to determine the helical scan pitch. 1.4 This practice does not establish acceptance criteria; they must be specified by the using party or parties. 1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ultrasonic Testing of Metal Pipe and Tubing

ASME B36.19-2022 不锈钢管

Stainless Steel Pipe

T/CFA 02010202-4-2021 非开挖管道施工用球墨铸铁顶管

本文件规定了顶管的术语和定义，球墨铸铁顶管结构、接口尺寸、外形及允许偏差，技术要求，试验方法，检验规则，标志、包装、存放、吊装、运输。

Ductile iron jacking pipe for trenchless pipeline construction

DIN 4927:2021 用于提升水的带法兰的钢上升管 公称直径 50 至 200

This document specifies dimensions, materials and requirements for flanged steel rising pipes. The pipes serve the raising of water from wells or tanks.

Flanged steel rising pipes for raising of water - Nominal diameter 50 to 200

ISO 21052:2021 球墨铸铁管道的约束连接系统.约束长度的计算规则

This document specifies a computation method used to determine the length of the ductile iron pipes to be restrained, when used for conveying raw water, drinking water, sewerage under pressure. This computation method takes into account all common pipeline route changes, including changes in the diameter of the pipeline itself and dead ends at the extremity of the pipeline, the outside diameter of the pipe, the system test pressure (to estimate the thrust), depth of cover, the characteristics of the soil surrounding the pipe and trench backfilling methods for a worldwide usage. The characteristics of the restrained joint are not covered by this document but can also be considered to determine the restraining length using any appropriate method. The computation method defined in this document is applicable to all types of restrained joint systems, with their operating pressure ratings of ductile iron pipelines complying with ISO 2531, ISO 7186 and NOTE 1 ISO 10804 deals with actual design of the joint for various operating pressures of the pipeline. NOTE 2 National standards or established calculation methods can be used instead of this ISO standard.

Restrained joint systems for ductile iron pipelines — Calculation rules for lengths to be restrained

ASTM A511/A511M-21a 无缝不锈钢机械管和空心棒的标准规范

1.1 This specification covers seamless stainless tubing for use in mechanical applications or as hollow bar for use in the production of hollow components such as, but not limited to nozzles, reducers, and couplings by machining where corrosion-resistant or high-temperature strength is needed. The grades covered are listed in Table 1 , Table 2, and Table 3. 1.2 This specification covers seamless cold-finished mechanical tubing and hollow bar and seamless hot-finished mechanical tubing and hollow bar in sizes up to 123⁄4 in. [325 mm] in outside nominal diameter (for round tubing) with wall thicknesses or inside diameters as required. 1.3 Tubes for mechanical applications shall be furnished in one of the following shapes, as specified by the purchaser: round, square, rectangular, or special. Tubes to be used as hollow bar shall be furnished in round shape. 1.4 Optional supplementary requirements are provided and when desired, shall be stated in the order. 1.5 The values stated in inch-pound units are to be regarded as the standard. Within the text, the SI units are shown in square brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar

ASTM A213/A213M-21b 无缝铁素体和奥氏体合金钢锅炉、过热器和热交换器管的标准规范

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

ASTM A335/A335M-21a 高温设备用无缝铁素体合金钢管标准规范

Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

ASTM A450/A450M-21 碳钢管和低合金钢管一般要求的标准规范

1.1 This specification2 covers a group of requirements which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21, 22, 23, 24, and 25, are mandatory requirements to the following ASTM tubular product specifications:3 Title of Specification ASTM DesignationA Electric-Resistance-Welded Carbon Steel and CarbonManganese Steel Boiler Tubes A178/A178M Seamless Cold-Drawn Low-Carbon Steel HeatExchanger and Condenser Tubes A179/A179M Seamless Carbon Steel Boiler Tubes for High-Pressure Service A192/A192M Seamless Medium-Carbon Steel Boiler and Superheater Tubes A210/A210M Electric-Resistance-Welded Carbon Steel HeatExchanger and Condenser Tubes A214/A214M Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins A498/A498M Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes A556/A556M Seamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System Service A822/A822M A These designations refer to the latest issue of the respective specifications. 1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1, 24, and 25 apply when the product specification or purchase order has a requirement for the test or analysis described by these sections. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes

ASTM A972/A972M-00(2021) 熔结环氧涂层管桩的标准规范

1.1 This specification covers pipe piles with protective fusion-bonded epoxy powder coating applied by the electrostatic spray, flocking, or fluidized bed process. NOTE 1—The coating applicator is identified throughout this specification as the manufacturer. 1.2 Other organic coatings may be used provided they meet the requirements of this specification. 1.3 Requirements for the powder coating are contained in Annex A1. 1.4 This specification is applicable for orders in either SI units (as Specification A972M) or inch-pound units [as Specification A972]. The values stated in either SI or inch-pound units are to be regarded as standard. Within the text, the inch-pound units are shown in brackets. 1.5 The following precautionary statement refers to the test method portion only, Section 8, of this standard: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Fusion Bonded Epoxy-Coated Pipe Piles

NF E86-700-2/A8*NF EN 13480-2 V1/A8:2021 金属工业管道 第2部分：材料

Metallic industrial piping - Part 2 : materials

ASTM A334/A334M-04a(2021) 低温设备用无缝和焊接碳和合金钢管的标准规范

1.1 This specification2 covers several grades of minimumwall-thickness, seamless and welded, carbon and alloy-steel tubes intended for use at low temperatures. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties. 1.2 Supplementary Requirement S1 of an optional nature is provided. This shall apply only when specified by the purchaser. NOTE 1—For tubing smaller than 1⁄2 in. [12.7 mm] in outside diameter, the elongation values given for strip specimens in Table 1 shall apply. Mechanical property requirements do not apply to tubing smaller than 1⁄8 in. [3.2 mm] in outside diameter and with a wall thickness under 0.015 in. [0.4 mm]. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service

ASTM A511/A511M-21 无缝不锈钢机械管和空心棒的标准规范

Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar

ASTM A501/A501M-21 热成型焊接和无缝碳钢结构管的标准规范

1.1?This specification covers black and hot-dipped galvanized hot-formed welded and seamless carbon steel square, round, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes. 1.

Standard Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

GSO ISO 8179-1:2021 球墨铸铁管、配件、附件及其接头 外锌基涂层 第1部分：带饰面层的金属锌

ISO 8179-1:2017 specifies an external protective coating system which is factory applied to ductile iron pipeline components as specified in ISO 2531, ISO 7186 and ISO 16631. This coating system comprises an electro-deposited metallic zinc-based coating of - pure metallic zinc with a purity of 99,99 %, - zinc and aluminium alloy with or without other metals, or - other zinc alloys followed by a finishing layer that can be bituminous paint or synthetic resin compatible with zinc-based coating. NOTE ISO 8179-2 deals with zinc-rich paint coating.

Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating — Part 1: Metallic zinc with finishing layer

GSO EN 10312:2021 用于输送水性液体（包括人类用水）的焊接不锈钢管 技术交货条件

This European Standard specifies the technical delivery conditions for light gauge welded stainless steel tubes, primarily for water application, including water intended for human consumption, supplied in straight lengths and suitable for connection by adhesive bonding, capillary fittings, compression fittings, press fittings or by inert gas welding. The standard covers the size range from 6 mm to 159 mm outside diameter in two grades of stainless steel from EN 10088-2.

Welded stainless steel tubes for the conveyance of aqueous liquids including water for human consumption – Technical delivery conditions

GSO ISO 16132:2021 球墨铸铁管和配件 水泥砂浆衬里密封层

ISO 16132:2016 specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings. It provides the performance requirements for short-term sealing efficiency, long-term durability and cyclic pressure, as well as the routine testing requirements for visual appearance, coating thickness and adhesion. ISO 16132:2016 is applicable to products for potable and other water applications.

Ductile iron pipes and fittings — Seal coats for cement mortar linings

OENORM EN 10357-2021 食品和化学工业用奥氏体、奥氏体-铁素体和铁素体纵焊不锈钢管

Austenitic, austenitic-ferritic and ferritic longitudinally welded stainless steel tubes for the food and chemical industry

GSO ASTM A377:2021 球墨铸铁压力管道规格标准索引

-

Standard Index of Specifications for Ductile Iron Pressure Pipe

ASTM F1545-15a(2021) 塑料衬里黑色金属管、配件和法兰的标准规范

1.1 This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dimensions, design, fabrication, working pressure and temperatures, test methods, qualification requirements, and markings are included. 1.1.1 This specification does not define the suitability of different liner materials to various chemical and operating environments. Refer to the manufacturer’s chemical resistance data for suitability recommendations. 1.1.2 This specification does not include products coated with plastics. 1.2 This specification covers plastic-lined pipe, flanges, and fittings as listed in Table 1. Pressure limitations shall be in accordance with ASME B16 Standards, except reduced pressure limitations may be established by the manufacturer, considering both pressure and temperature limitations of the ferrous metal housing and the sealing ability of the liner. NOTE 1—In this specification, propylene plastics cover those materials defined as both polypropylene plastics and propylene plastics in Terminology F412. Both materials are identified as “PP” on the product. Note that this is at variance with Terminology D1600, where “PP” is the abbreviation for polypropylene. 1.3 The plastic-lined flanged pipe and fitting assemblies are limited to temperatures shown in Table 2. End users should consult with manufacturers as to the likely result of using a particular lined piping component at temperatures below the rated minimum. NOTE 2—The temperature limitations are based on noncorrosive test conditions. Use in specific aggressive environments may alter temperature limitations. In such instances, specific temperature limits shall be established by mutual agreement between the purchaser and the manufacturer. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges