27.060.10 液体和固体燃料燃烧器 标准查询与下载

KS B 8005-2010 燃油用具用芯

이 표준은 섬유로 만들어진 기름 연소 기기용 심지(이하 심지라 한다.)에 대하여 규정한다.

Wicks for oil burning appliances

KS B 8008-2010(2020) 燃油器具填料泵

Filler pumps for oil burning appliances

KS B 8023-2010(2020) 油供应铜管油类燃烧器具

Oil supply copper pipe for oil burning appliances

KS B 6034-2010 家庭用小型石油热水器

이 표준은 등유, 경유 또는 중유를 연료로 하고, 연료 소비량1) 5 800 g/h 이하이

Oil burning water heaters for domestic use

KS B 8010-2010 燃油用具油量调节阀

이 표준은 기름 탱크로부터의 기름의 낙차가 2.5 m 이하에서 사용되는 기름 연소 기기용

Oil controler for oil burning appliances

ISO 22968:2010 强制通风油燃器

This International Standard specifies the terminology, test procedures and general requirements for the construction and operation of automatic forced draught oil burners supplied with a fuel having a viscosity at the burner inlet of 1,6 mm2/s (cSt) to 6 mm2/s (cSt) at 20 °C or higher, boiling petroleum in accordance with ISO 8217-based first raffinates, and the provision of related control and safety devices. It is applicable to the following: a) automatic oil burners (hereinafter called “burners”) fitted with a combustion air fan and equipped as described in Clause 5, intended for use in appliances of different types and operated with fuel oils; b) single burners with a single combustion chamber, for which, where such burners are fitted to a single appliance, the requirements of the relevant appliance standard also apply; c) single-fuel and dual-fuel burners when operating only on oil; d) the oil function of dual-fuel burners designed to operate simultaneously on gaseous and liquid fuels, which, for the former, the requirements of ISO 22967 also apply. It is not applicable to burners used in direct fired processes either with defined combustion chamber applications or where the combustion chamber wall surface temperature is greater than 750 °C or the heat-transfer medium temperature is greater than 500 °C.

Forced draught oil burners

DS/EN 299:2010 油压雾化喷嘴 角度和喷雾特性的测定

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles.

Oil pressure atomizing nozzles - Determination of the angle and spray characteristics

BS EN 267:2010 整体型喷雾燃油器试验方法

Automatic forced draught burners for liquid fuels

BS EN 267:2009+A1:2011 液体燃料用自迫干燥燃烧器

Automatic forced draught burners for liquid fuels

ASTM D6615-10 喷射B类宽馏分航空涡轮机燃料标准规范

1.1 This specification covers the use of purchasing agencies in formulating specifications for purchases of aviation turbine fuel under contract. 1.2 This specification defines one specific type of aviation turbine fuel for civil use. This fuel has advantages for operations in very low temperature environments compared with other fuels described in Specification D1655. This fuel is intended for use in aircraft that are certified to use such fuel. Note 18212;The technical requirements of this product, at the time of the first publication of this specification, are substantially identical to the requirements of Jet B in Specification D1655.

Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel

ASTM D6550-10 超临界液相色谱法测定汽油中烯烃含量的标准试验方法

Gasoline-range olefinic hydrocarbons have been demonstrated to contribute to photochemical reactions in the atmosphere, which result in the formation of photochemical smog in susceptible urban areas. The California Air Resources Board (CARB) has specified a maximum allowable limit of total olefins in motor gasoline. This necessitates an appropriate analytical test method for determination of total olefins to be used both by regulators and producers. This test method compares favorably with Test Method D1319 (FIA) for the determination of total olefins in motor gasolines. It does not require any sample preparation, has a comparatively short analysis time of about 10 min, and is readily automated. Alternative methods for determination of olefins in gasoline include Test Methods D6839 and D6296.1.1 This test method covers the determination of the total amount of olefins in blended motor gasolines and gasoline blending stocks by supercritical-fluid chromatography (SFC). Results are expressed in terms of mass % olefins. The application range is from 1 to 25 mass % total olefins. 1.2 This test method can be used for analysis of commercial gasolines, including those containing varying levels of oxygenates, such as methyl tert/butyl ether (MTBE), diisopropyl ether (DIPE), methyl tert/amyl ether (TAME), and ethanol, without interference. Note 18212;This test method has not been designed for the determination of the total amounts of saturates, aromatics, and oxygenates. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography

LST EN 299-2009 油压雾化喷嘴 角度和喷雾特性的测定

Oil pressure atomizing nozzles - Determination of the angle and spray characteristics

DIN EN 299:2009 油压雾化喷嘴.角度和喷雾特性测定.英文版本EN 299-2009-11

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles

Oil pressure atomizing nozzles - Determination of the angle and spray characteristics; English version of DIN EN 299:2009-11

LST EN ISO 23553-1:2009 燃油燃烧器和燃油器具的安全和控制装置 特殊要求 第1部分：燃油燃烧器的关闭装置（ISO 23553-1:2007，包括 Cor 1:2009）

Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Shut-off devices for oil burners (ISO 23553-1:2007, including Cor 1:2009)

DIN EN ISO 23553-1:2009 燃油器和燃油器具的安全和控制装置.特殊要求.第1部分:燃油器的断油装置(ISO 23553-1:2007,包修改件1:2009),德文版本EN ISO 23553-1:2009

This part of ISO 23553 specifies safety, constructional and performance requirements, and testing of safety shut-off devices, for liquid fuels. This part of ISO 23553 covers type testing only. It applies to safety shut-off devices which: -- are designed as e.g. automatic valves or fast-closing devices; are used in combustion plants to interrupt the flow of liquid fuels with or without delay on closing and with or without delay on opening; are for use with fuel oils; NOTE For other liquid fuels, additional test methods can be agreed between the manufacturer and the test authority -- form part of a device having other function(s), such as oil pumps. In this case the test methods apply to those parts or components of the device forming the safety shut-off device, i.e. those parts which are necessary for the closing function: have declared maximum working pressures up to and including 5 000 kPa, for use on burners or in appliances using liquid fuels: - are directly or indirectly operated electrically or by mechanical or hydraulic means; are fitted with or without closed-position indicator switches. The methods of test given in this part of ISO 23553 are intended for product type testing.

Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Shut-off devices for oil burners (ISO 23553-1:2007, including Cor 1:2009); English version of DIN EN ISO 23553-1:2009-10

BS EN 299:2009 油压雾化喷嘴.角度和喷射特性的测定

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles.

Oil pressure atomizing nozzles - Determination of the angle and spray characteristics

NF E31-311-1:2009 燃油器和燃油设备用安全性和控制装置.特殊要求.第1部分:燃油器用切断装置

Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1 : shut-off devices for oil burners.

DS/EN ISO 23553-1:2009 燃油燃烧器和燃油器具的安全和控制装置 特殊要求 第1部分：燃油燃烧器的关闭装置

This part of ISO 23553 specifies safety, constructional and performance requirements, and testing of safety shut-off devices, for liquid fuels.This part of ISO 23553 covers type testing only.

Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Shut-off devices for oil burners

EN 299:2009 油压雾化喷嘴.角度和喷雾特性测定

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles.

Oil pressure atomizing nozzles - Determination of the angle and spray characteristics

BS EN ISO 23553-1:2009 燃油器和燃油器具的安全性和控制装置.详细要求.第1部分:燃油器的断油装置(ISO 23553-1-2007,包括Cor 1-2009)

This part of ISO 23553 specifies safety, constructional and performance requirements, and testing of safety shut-off devices, for liquid fuels. This part of ISO 23553 covers type testing only. It applies to safety shut-off devices which: -are designed as e.g. automatic valves or fast-closing devices; -are used in combustion plants to interrupt the flow of liquid fuels with or without delay on closing and with or without delay on opening; -are for use with fuel oils; -form part of a device having other function(s), such as oil pumps. In this case the test methods apply to those parts or components of the device forming the safety shut-off device, i.e. those parts which are necessary for the closing function; -have declared maximum working pressures up to and including 5 000 kPa, for use on burners or in appliances using liquid fuels; -are directly or indirectly operated electrically or by mechanical or hydraulic means; -are fitted with or without closed-position indicator switches. The methods of test given in this part of ISO 23553 are intended for product type testing.

Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Shut-off devices for oil burners (ISO 23553-1:2007, including Cor 1:2009)