27.060.10 液体和固体燃料燃烧器 标准查询与下载
共找到 326 条与 液体和固体燃料燃烧器 相关的标准，共 22 页
Measurement method of NOx emission rate for open type forced draught oil burning space heaters
- ICS
- 27.060.10
- CCS
- 发布
- 2014-12-15
- 实施
이 표준은 연료 소비량1)이 600 g/h 이하인 강제 통기형 개방식 기름 난로(이하 난로라 한다.)로부터 배출되는 질소 산화물 배출량의 측정 방법에 대하여 규정한다.
Measurement method of NOx emission rate for open type forced draught oil burning space heaters
- ICS
- 27.060.10
- CCS
- Q83
- 发布
- 2014-12-15
- 实施
- 2014/12/15
Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves (ISO 23553-1:2014)
- ICS
- 27.060.10
- CCS
- 发布
- 2014-09-16
- 实施
- 2014-09-16
Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves (ISO 23553-1:2014); German version EN ISO 23553-1:2014
- ICS
- 27.060.10
- CCS
- J99
- 发布
- 2014-09
- 实施
Safety and control devices for oil burners and oil-burning appliances. Particular requirements. Automatic and semi-automatic valves
- ICS
- 27.060.10
- CCS
- J99
- 发布
- 2014-06-30
- 实施
- 2014-06-30
本标准规定了生物质炕炉的型号表示方法、技术要求、检验方法和检验规则等。本标准适用于燃用生物质及其成型燃料，以火炕供暖为主，或兼有其他功能(热水供暖、炊事)的炉具。
General specification for biomass Kang stove
- ICS
- 27.060.10
- CCS
- F13
- 发布
- 2014-06-29
- 实施
- 2014-11-01
Dieser Teil der ISO 23553 legt die Anforderungen an Sicherheit, Konstruktion und Leistung sowie die Prufung von automatischen und halbautomatischen Ventilen fur Ol fest. Er gilt fur automatische und halbautomatische Ventile, die: als Schnellschlusseinrichtungen ausgelegt sind; in Verbrennungsanlagen eingesetzt werden, um den Oldurchfluss mit oder ohne Verzogerung des Schliesvorgangs sowie mit oder ohne Verzogerung des Offnungsvorgangs zu unterbrechen; fur den Einsatz mit Olsorten ohne Benzin (z. B. Diesel, Rohol, Schwerol oder Kerosin) vorgesehen sind; ANMERKUNG 1 Fur weitere Olsorten (z. B. Olemulsionen) konnen zwischen Hersteller und Prufstelle zusatzliche Prufverfahren vereinbart werden. ANMERKUNG 2 Olsorten aus Raffinerieprozessen sind klassifiziert als ISO-F-D nach ISO 8216-99 und bilden einen Teil einer Einrichtung mit (einer) anderen Funktion(en) z. B. Olpumpen. In diesem Fall gelten die Prufverfahren fur diejenigen Bauteile oder Komponenten der Einrichtung, die die automatischen und halbautomatischen Ventile bilden, d. h. die Bauteile, die fur die Schliesfunktion erforderlich sind; fur die Anwendung an Brennern oder in Geraten vorgesehen sind, die Ol nutzen; direkt oder indirekt elektrisch oder durch mechanische oder hydraulische Hilfsmittel betrieben werden; mit Anzeigen fur die Geschlossenstellung ausgestattet sind oder nicht. Dieser Teil der ISO 23553 behandelt nur die Typprufung.
Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves
- ICS
- 27.060.10
- CCS
- J66
- 发布
- 2014-05
- 实施
Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves
- ICS
- 27.060.10
- CCS
- J16
- 发布
- 2014-05
- 实施
1.1 This specification covers four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment under various climatic and operating conditions. These fuels are not intended for use in residential heaters, small commercial boilers, combustion engines, or marine applications, 1.1.1 Grades RFO4, RFO5L, RFO5H, and RFO6 are used lubricating oil blends, with or without distillate or residual fuel oil, or both, of increasing viscosity and are intended for use in industrial burners equipped to handle these types of recycled fuels. Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1. 1.2 This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run. 1.3 Nothing in this specification shall preclude observance of national or local regulations, which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels from used oil are required to meet certain criteria before use as a fuel. Note 2: For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR 279. Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865. 1.4 The values stated in SI units are to be regarded as standard; non-SI units, when given, are for information only.
Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
- ICS
- 27.060.10
- CCS
- 发布
- 2014
- 实施
5.1 The acid strength, as measured by pHe, is a good predictor of the corrosion potential of ethanol fuels. It is preferable to total acidity because total acidity does not measure acid strength; overestimates the contribution of weak acids, such as carbonic acid; and can underestimate the corrosion potential of low concentrations of strong acids, such as sulfuric acid. 1.1 This test method covers a procedure to determine a measure of the acid strength of high ethanol content fuels. These include denatured fuel ethanol and ethanol fuel blends. The test method is applicable to denatured fuel ethanol and ethanol fuel blends containing ethanol at 518201;% by volume, or more. 1.2 Acid strength as measured in this test method is defined as pHe. A pHe value for alcohol solutions is not comparable to pH values of water solutions. 1.2.1 The value of pHe measured will depend somewhat on the fuel blend, the stirring rate, and the time the electrode is in the fuel. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 Hydrogen ion activity in water is expressed as pH and hydrogen ion activity in ethanol is expressed as pHe. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Determination of pHe of Denatured Fuel Ethanol and Ethanol Fuel Blends
- ICS
- 27.060.10
- CCS
- 发布
- 2014
- 实施
1.1 This specification covers four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment under various climatic and operating conditions. These fuels are not intended for use in residential heaters, small commercial boilers, combustion engines, or marine applications, 1.1.1 Grades RFO4, RFO5L, RFO5H, and RFO6 are used lubricating oil blends, with or without distillate or residual fuel oil, or both, of increasing viscosity and are intended for use in industrial burners equipped to handle these types of recycled fuels. Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1. 1.2 This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run. 1.3 Nothing in this specification shall preclude observance of national or local regulations, which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels from used oil are required to meet certain criteria before use as a fuel. Note 2: For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR 279. Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865. 1.4 The values stated in SI units are to be regarded as standard; non-SI units, when given, are for information only.
Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
- ICS
- 27.060.10
- CCS
- 发布
- 2014
- 实施
本标准规定了生物质炊事大灶的术语和定义，型号表示方法，技术要求，检验方法，检验规则以及标志、包装、储存和使用寿命等。本标准适用于炊事火力强度大于10kW，燃用生物质及其成型燃料的灶具。
General specification for biomass institutional stoves
- ICS
- 27.060.10
- CCS
- F13
- 发布
- 2013-11-28
- 实施
- 2014-04-01
This part of BS 5410 gives recommendations and guidance on the design, installation,commissioning and maintenance of oil burning installations for heating,hot water and steam supply services having a total rated output of over 45 kW and/or an oil storage capacity above 3 500 L. This part of BS 5410 is applicable to installations burning liquid fuel conforming to BS 2869:2010+A1,including biofuels, for example those containing fatty acid methyl esters (FAME) conforming to BS EN 14214, and blends thereof. The standard covers the provision of new installations and also gives guidance on the modernizing of existing installations. The standard also gives recommendations and guidance on the selection and installation of oil tanks associated with these installations. This part of BS 5410 is applicable to the oil burning equipment forming part of a multi-fuel installation in which oil is not burnt simultaneously with any other fuel. It is not applicable to oil fired systems for marine installations. The standard also gives recommendations on thermal fluid heaters and on portable plants, for example those used for emergency or temporary heat supply. The standard is intended for use by designers, specifiers,installers and building owners.
Code of practice for oil firing.Part 2:Installations over 45 kW output capacity for space heating, hot water and steam supply services
- ICS
- 27.060.10
- CCS
- J98
- 发布
- 2013-03-31
- 实施
- 2013-03-31
Gas burners, gas/oil burner and pulverized solid fuel/gas burners of steam and hot-water boilers. Acceptance test. Basis requirements
- ICS
- 27.060.10
- CCS
- 发布
- 2013
- 实施
- 2015-01-01
Pellet burners for heating boilers the output up to 100 kW. General technical requirements and test method
- ICS
- 27.060.10
- CCS
- 发布
- 2013
- 实施
- 2015-01-01
이 표준은 초기 라피네이트를 기초로 한 KS M ISO 8217에 따라 온도 20 ℃ 또는
Forced draught oil burners
- ICS
- 27.060.10
- CCS
- J83
- 发布
- 2012-12-11
- 实施
- 2012-12-11
