31.220 电子电信设备用机电元件 标准查询与下载

GB/T 12993-1991 电子设备热性能评定

本标准规定了电子设备的热性能评定。 本标准适用于电子设备自然冷却和强迫冷却热性能的评定。

Thermal performances evaluation for electronic equipment

GB/T 12992-1991 电子设备强迫风冷热特性测试方法

本标准规定了正常大气压条件下电子设备强迫风冷的温度、流速（流量）和压力的测试方法。 本标准适用于正常大气条件下强迫风冷电子设备的电子元器件表面温度、环境温度、机箱（柜）表面温度的测量，通风系统空气流速（或流量）的测量及风道内气流的静压和动压的测量。

Measuring methods of thermal characteristic for forced air cooling of electronic equipment

GB 9393-1988 STZ3型电子测量仪器用连接器

STZ3 type connector for electronic measurement instrument

BS EN IEC 61169-70:2024 射频连接器 HD-BNC 系列射频同轴连接器的截面规范 特性阻抗75Ω

Radio-frequency connectors - Sectional specification for series HD-BNC radio-frequency coaxial connectors. Characteristic Impedance 75 Ω

FprEN IEC 61169-70:2023 射频连接器 第70部分：HD-BNC 系列射频同轴连接器的分规范 特性阻抗 75 Ω

IEC 61169-70:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) of HD-BNC series RF coaxial connectors together with the pro forma blank detail specification. HD-BNC series connectors with characteristic impedance of 75 Ω are used with RF cables or micro-strips in microwave, telecommunication, wireless and other fields. The operating frequency limit is up to 18 GHz. It also prescribes mating face dimensions for general purpose connectors, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series HD-BNC RF connectors. This specification indicates the recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.

Radio-frequency connectors - Part 70: Sectional specification for series HD-BNC radio-frequency coaxial connectors - Characteristic Impedance 75 Ω

KS C IEC 62528-2020 基于嵌入式内核的集成电路的标准可测试性方法

Standard Testability Method for Embedded Core-based Integrated Circuits

KS C IEC 60512-7-2019 电子设备机电元件 基本试验程序和测量方法 第7部分：机械操作试验和密封试验

Electromechanical components for electronic equipment — Basic testing procedures and measuring methods — Part 7: Mechanical operating tests and sealing tests

KS C 6116-2016 报警系统，第2部分入侵者报警系统的要求第三部分建筑物中红外光束中断探测器的要求

Alarm systems, Part 2：Requirements for intruder alarm systems－Section Three－Requirements for infrared-beaminterruption detectors in buildings

KS C IEC 62528-2015(2020) 嵌入式核心集成电路的标准可测性方法

Standard Testability Method for Embedded Core-based Integrated Circuits

KS C IEC 62528:2015 嵌入式核心集成电路的标准可测试性方法

Standard Testability Method for Embedded Core-based Integrated Circuits

GSO IEC 60512-12-7:2015 电子设备的连接 测试和测量 第12-7部分：焊接测试 测试 12(g)：可焊性、润湿称重方法

This part of IEC 60512, when required by the detail specification, is to be used for testing connectors within the scope of IEC technical committee 48. This test may also be used for similar components when specified in a detail specification. The object of this test is to define a standard test method to assess the solderability of the terminations of a component designed for use with printed boards or for other applications using similar soldering techniques.

Connectors for electronic equipment - Tests and measurements - Part 12-7: Soldering tests - Test 12g: Solderability, wetting balance method

GSO IEC 60512-1:2015 电子设备连接 测试和测量 第1部分：一般原则

This part of IEC 60512 is intended to be used as a basic specification. It contains basic test methods and procedures which, when required by the detail specification, are used for testing connectors within the scope of technical committee 48. They may also be used for similar devices when specified in a detail specification. The object of this standard is to establish test methods and measurement procedures for use in specifications for connectors. This standard is to be used in conjunction with the generic, sectional and detail specification which will select and prescribe the tests to be used, the required degree of severity for each of them and the permissible performance limits. The detail specification will also specify the deviations in procedure, which may be inevitable when applying a test to the type of component under consideration, and it will further specify any special procedures which may be required. In the event of conflict between this basic specification and any individual component specification, the requirements of the component specification will apply. NOTE 1 RF connectors will not be dealt with by this technical committee as they will be covered by technical committee 46, together with r.f. cables. NOTE 2 Sockets for components such as crystals or electronic tubes will be considered in co-operation with the relevant technical committee. NOTE 3 Safety requirements for switches will not be developed by this technical committee as they are covered by subcommittee 23J.

Connectors for electronic equipment - Tests and measurements - Part 1: General

GSO IEC 62528:2014 基于内核的集成电路可测试性的标准方法

IEEE Std 1500 has developed a standard design-for-testability method for integrated circuits (ICs) containing embedded nonmergeable cores. This method is independent of the underlying functionality of the IC or its individual embedded cores. The method creates the necessary requirements for the test of such ICs, while allowing for ease of interoperability of cores that may have originated from different sources.

Standard Testability Method for Embedded Core-based Integrated Circuits

KS C IEC 60512-7-2014(2019) 电子设备机电组件 - 基本测试程序和测量方法 - 第7部分:机械操作测试和密封测试

Electromechanical components for electronic equipment — Basic testing procedures and measuring methods — Part 7: Mechanical operating tests and sealing tests

KS C IEC 60512-7:2014 电子设备用机电元件 基本试验程序和测量方法 第7部分：机械操作试验和密封试验

Electromechanical components for electronic equipment — Basic testing procedures and measuring methods — Part 7: Mechanical operating tests and sealing tests

KS C 6113-2014 报警系统·艺术1·一般要求·功能三·环境试验

Alarm systems－Part 1：General requirements－Section Three－Environmental testing

KS C 6112-2014 报警系统第 1 条一般要求-第 2 节动力装置、测试方法和性能标准

Alarm systems－Part 1：General requirements-Section Two-Power units, test methods and performance criteria

KS C 6114-2014 报警系统-第1部分-一般要求-第四部分-操作规范

Alarm systems-Part 1：General requirements－Section Four-Code of practice

KS C IEC 60512-1-2014 电子设备连接器 试验和测量 第1部分：概述

Connectors for electronic equipment－Tests and measurements－Part 1：General

KS C IEC 60512-6-5-2014 电子设备机电部件 基本试验程序和测量方法 第6部分：动态应力试验 第5节：试验6e：随机振动

Electromechanical components for electronic equipment－Basic testing procedures and measuring methods－Part 6：Dynamic stress tests－Section 5：Test 6e：Random vibration