31.220 电子电信设备用机电元件 标准查询与下载

KS C 7026-2013(2018) 用于音频/视频系统远程控制接收器

Remote control receiver for audio/video system

KS C 7026-2013 音频和视频机器用遥控接收器

이 표준은 가정과 사무실 등 이와 유사한 장소에서 사용되는 TV 등 서로 다른 오디오기기와

Remote control receiver for audio/video system

TIS 2036-2009 电子设备用连接器.试验和测量.第1部分:总则

Connectors for electronic equipment.tests and measurements.part 1: general

IPC TM-650 2.5.6.1-2007 REV B介质强度焊料的面具

This specification covers paper made from cellulosic fibers intended as a reinforcing material in laminated plastics for electrical and electronic use.

Solder Mask - Dielectric Strength REV B

IPC WHMA-A-620A-2006 有线和束线组装的要求与接受

Connector misalignment precludes contact of all wires to the IDC contacts (Figure 6-15, arrow).

Requirements and Acceptance for Cable and Wire Harness Assemblies

IPC TM-650 2.4.24.6-2006 测试方法手册

The purposes of the Wetting Balance Standard Weight Comparison test were to

TEST METHODS MANUAL

JIS C 5402-12-7:2005 电子设备用连接器.试验和测量.第12-7部分:锡焊试验.试验12g:湿润平衡法测定可焊性

この規格は，電子機器用コネクタ(以下.コネクタという。)において，プリント配線板向けに，又は類似のはんだ付け技術を用いる他の用途向けに設計したコネクタにおけるターミネーションのはんだ付け性を評価するための試験方法について規定する。

Connectors for electronic equipment -- Tests and measurements -- Part 12-7: Soldering tests -- Test 12g: Solderability, wetting balance method

IPC WP-008-2005 设立离子色谱能力

It is the position of IPC’s Technical Activities Executive Committee that the use and implementation of IPC publications is voluntary and is part of a relationship entered into by customer and supplier. When an IPC publication is updated and a new revision is published, it is the opinion of the TAEC that the use of the new revision as part of an existing relationship is not automatic unless required by the contract. The TAEC recommends the use of the latest revision. Adopted October 6, 1998

Setting Up Ion Chromatography Capability

KS C IEC 60512-6-2004(2009) 电子设备用机电元件基本试验程序和测量方法第6部分:气候试验和焊接试验

Electromechanical components for electronic equipment－Basic testing procedures and measuring methods－Part 6：Climatic tests and soldering tests

KS C IEC 60512-8-2004(2009) 电子设备用机电元件基本试验程序和测量方法第8部分:连接器试验（机械）及触点和终端的机械试验

Electromechanical components for electronic equipment－Basic testing procedures and measuring methods－Part 8：Conenctor tests(mechanical) and mechanical tests on contacts and terminations

KS C IEC 60512-12-7-2004(2009) 电子设备用连接器试验和测量第12－7部分:焊接试验试验试验12g:可焊性湿平衡法

Connectors for electronic equipment－Tests and measurements－Part 12－7：Soldering tests－Test 12g：solderability, wetting balance method

KS C IEC 60512-1-2004(2009) 电子设备连接器试验和测量第1部分:总则

Connectors for electronic equipment－Tests and measurements－Part 1：General

IPC TM-650 2.3.34-2004 通量固形物含量 修订本C

aterial in this Test Methods Manual was voluntarily established by Technical Committees of the IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement by the IPC.

Solids Content, Flux Revision C

IPC TM-650 2.3.32-2004 通量诱导腐蚀(铜镜法) 修订本D

Material in this Test Methods Manual was voluntarily established by Technical Committees of the IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement by the IPC.

Flux Induced Corrosion (Copper Mirror Method) Revision D

IPC TM-650 2.3.33-2004 熔剂中的卤化物显现(银铬法) 修订本D

aterial in this Test Methods Manual was voluntarily established by Technical Committees of the IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement by the IPC.

Presence of Halides in Flux, Silver Chromate Method Revision D

IPC TM-650 2.3.35-2004 定量(氯化物和溴化物)卤化物含量 修订本C

aterial in this Test Methods Manual was voluntarily established by Technical Committees of the IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement by the IPC.

Halide Content, Quantitative (Chloride& Bromide) Revision C

IPC TM-650 2.6.4-2004 印制板出气 修订版B

This specification establishes specific test methods to evaluate the performance and reliability of surface mount solder attachments of electronic assemblies. It further establishes different levels of performance and reliability of the solder attachments of surface mount devices to rigid, flexible and rigid-flex circuit structures. In addition, it provides an approximate means of relating the results from these performance tests to the reliability of solder attachments for the use environments and conditions of electronic assemblies.

Outgassing, Printed Boards Revision B

IPC TM-650 2.6.3-2004 印刷板水分和电阻绝缘 修订版F

This document is presented to assist in selecting the test analyzer, test parameters, test data, and fixturing required to perform electrical test(s) on all unpopulated printed boards without embedded components (i.e., resistors, capacitors, etc.).

Moisture and Insulation Resistance, Printed Boards Revision F

ANSI/VITA 1.7-2003 96针及160针DIN/IEC连接器标准用增长的电流等级

This standard describes increased current levels, test methods, test data and compliance criteria for 3 row DIN and 5 row DIN connectors when used in VME, VME64 and VME64 Extension P1/J1 and P2/J2 pin out arrangements.

Increased Current Level for 96 Pin & 160 Pin DIN/IEC Connector Standard

KS C IEC 60512-9-2003(2008) 电子设备用机电元件基本试验程序和测量方法第9部分:其它试验

Electromechanical components for electronic equipment－Basic testing procedures and measuring methods－Part 9：Miscellaneous tests