31.220.10 插头和插座装置、连接器 标准查询与下载

BS EN 61076-2-113:2017 电子设备连接器 产品要求 圆形连接器 带电源和信号触点的 M12 螺钉锁定连接器的详细规范 用于频率高达 100 MHz 的数据传输

What is BS EN 61076-2-113 – Circular connectors about ? BS EN 61076-2-113 is the second part of an international standard used for connectors that specifies the test methods and characteristics of the circular connectors. BS EN 61076-2-113 describes M12 circular connectors with two data pairs and power contacts with current ratings up to 12 A, that are typically used for data and power applications in industrial premises. These connectors consist of both fixed and free connectors either rewireable or non-rewireable, with screw-locking. Male connectors have round contacts diameters of 1,50 mm, 1,00 mm and 0,60 mm.   The different codings provided by BS EN 61076-2-113 prevent the mating of accordingly coded   male or female connectors to any other similarly sized interfaces covered by other standards   and the cross-mating between the different cod...

Connectors for electronic equipment. Product requirements - Circular connectors. Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz

GSO IEC/PAS 61076-3-119:2017 电子设备连接器 产品要求 第3-119部分：矩形连接器 用于频率高达 100 MHz 的工业环境的带推挽耦合的非屏蔽、自由和固定 10 路连接器的详细规范

This part of IEC 61076 establishes specifications and test requirements for a connector with ten contacts, for use in industrial environments. This PAS specifies free and fixed connector inserts, with round contacts, suitable for screw or crimp terminations. Other terminations techniques, as solder or printed board connections are upon agreement between manufacturer and user. The free and fixed connectors have a pushpull locking mechanism for IP65 and IP67 protection according to IEC 60529. Connectors according this PAS are without breaking capacity COC according to IEC 61984, therefore they are not intended to be engaged or disengaged in normal use when live or under load, if not otherwise specified by the manufacturer.

Connectors for electronic equipment - Product requirements - Part 3-119: Rectangular connectors - Detail specification for unshielded, free and fixed 10-way connectors with push-pull coupling for industrial environments with frequencies up to 100 MHz

GSO IEC 61076-3-118:2017 电子设备连接器 产品要求 第3-118部分：矩形连接器 带推拉耦合的 4 极加 PE 电源连接器的详细规范

1.1 General considerations This part of IEC 61076 establishes specifications and test requirements for a connector with four contacts plus PE contact, for use in industrial environments. NOTE For a definition of PE, see IEV, for example IEV 195-02-09. This International Standard specifies free and fixed connectors, with round contacts, suitable for screw or crimp terminations. Other terminations techniques, as solder or printed board connections are upon agreement between manufacturer and user. The free and fixed connectors have a push-pull locking mechanism for IP65 and IP67 protection according to IEC 60529. The PE contact is first-make last-break. Connectors according this International Standard are without breaking capacity COC according to IEC 61984, therefore they are not intended to be engaged or disengaged in normal use when live or under load, if not otherwise specified by the manufacturer.

Connectors for electronic equipment - Product requirements - Part 3-118: Rectangular connectors - Detail specification for a 4 pole plus PE power connector with push-pull coupling

GSO IEC 61076-4-116:2017 电子设备连接器 产品要求 第4-116部分：印制板连接器 具有集成屏蔽功能的高速两部分连接器的详细规范

This International Standard establishes specifications and test requirements for a high-speed two-part connector with integrated shielding function for use as a printed board connector in industrial environments. The connectors connect a backplane to printed boards.

Connectors for electronic equipment - Product requirements - Part 4-116: Printed board connectors - Detail specification for a high-speed two-part connector with integrated shielding function

GSO IEC/PAS 61076-2-110:2017 电子设备连接器 产品要求 第2-110部分：圆形连接器 带螺钉锁紧的圆形连接器 M12 x 1 的详细规范 用于频率高达 500 MH 的高速以太网和高速数据通信

This Publicly Available Specification (PAS) describes M12 circular connectors for use in industrial environments for high speed Ethernet and high speed data transfer. Applications include, but are not limited to, vision systems and data acquisition. Screw locking M12 connectors consist of fixed and free connectors. Male connectors have round contacts Ø 0,6mm.

Connectors for electronic equipment - Product requirements - Part 2-110: Circular connectors - Detail specification for circular connectors M12 x 1 with screw-locking, for high speed Ethernet and high speed data communication with frequencies up to 500 MH

GSO IEC/TR 62652:2017 电气负载下接合和分离对用于支持 IEEE 802.3af（以太网供电）应用的布线中连接器接口的影响

This Technical Report is intended to provide information on the effects of engaging and separating under electrical load on the connector interfaces in cabling, used to support IEEE 802.3af (Power-over-Ethernet (PoE)) applications.

Effects of engaging and separating under electrical load on connector interfaces in cabling used to support IEEE 802.3af (power-over-ethernet) applications

EN 61076-3-122:2017 电气和电子设备连接器 产品要求 第 3-122 部分：用于恶劣环境中 I/O 和千兆以太网应用的 8 路、屏蔽、自由和固定连接器的详细规范

IEC 61076-3-122:2017 covers 8-way, shielded, free and fixed rectangular connectors for I/O and Gigabit Ethernet applications, suitable for use in harsh environments, and is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for this family of connectors.

Connectors for electrical and electronic equipment - Product requirements - Part 3-122: Detail specification for 8-way, shielded, free and fixed connectors for I/O and Gigabit Ethernet applications in harsh environments

DIN EN 60603-7-82:2017 电子设备连接器 第 7-82 部分：8 路、12 触点、屏蔽、自由和固定连接器的详细规范，用于频率高达 2000 MHz 的数据传输（IEC 60603-7-82:2016）；德文版 EN 60603-7-82:2016

Connectors for electronic equipment - Part 7-82: Detail specification for 8-way, 12 contacts, shielded, free and fixed connectors, for data transmission with frequencies up to 2 000 MHz (IEC 60603-7-82:2016); German version EN 60603-7-82:2016

EN 61076-2-113:2017 电子设备连接器 产品要求 第 2-113 部分：圆形连接器 频率高达 100 MHz 的数据传输用 M12 螺钉锁定连接器的详细规范

IEC 61076-2-113:2017 describes M12 circular connectors with two data pairs and power contacts with current ratings up to 12 A, that are typically used for data and power applications in industrial premises. These connectors consist of both fixed and free connectors either rewireable or non rewireable, with screw-locking. Male connectors have round contacts diameters of 1,50 mm, 1,00 mm and 0,60 mm. The different codings provided by this document prevent the mating of accordingly coded male or female connectors to any other similarly sized interfaces covered by other standards and the cross-mating between the different codings provided by this document. M12 is the dimension of the thread of the screw locking mechanism of these circular connectors. Key words: Connectors, Circular Connectors, M12.

Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz

IEC 60603-7-81:2015/COR1:2017 电子设备连接器 第 7-81 部分：频率高达 2000 MHz 的数据传输用 8 路、屏蔽、自由和固定连接器的详细规范 勘误表 1

Connectors for electronic equipment - Part 7-81: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 2000 MHz - Corrigendum 1

DIN EN 61076-3-120:2017 电子设备连接器. 产品要求. 第3-120部分: 矩形连接器. 直流额定电压250 V, 额定电流30 A的带弹簧锁可重接电源连接器详细规格(IEC 61076-3-120-2016); 德文版本

Connectors for electronic equipment - Product requirements - Part 3-120: Rectangular connectors - Detail specification for rewirable power connectors with snap locking for rated voltage of 250 V d.c. and rated current of 30 A (IEC 61076-3-120:2016); Germa

DIN EN 61076-3-110:2017 电子设备用连接器.产品要求.第3-110部分:频带在3000 MHz以下的数据传输用活动和固定连接器的详细规范(IEC 61076-3-110-2016)；德文版本EN 61076-3-110-2016

Connectors for electronic equipment - Product requirements - Part 3-110: Detail specification for free and fixed connectors for data transmission with frequencies up to 3 000 MHz (IEC 61076-3-110:2016); German version EN 61076-3-110:2016

IEC 61076-3-122:2017 电气和电子设备连接器 产品要求 第 3-122 部分：用于恶劣环境中 I/O 和千兆以太网应用的 8 路、屏蔽、自由和固定连接器的详细规范

This part of IEC 61076 covers 8-way, shielded, free and fixed rectangular connectors for I/O and Gigabit Ethernet applications, suitable for use in harsh environments, and is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for this family of connectors.

Connectors for electrical and electronic equipment - Product requirements - Part 3-122: Detail specification for 8-way, shielded, free and fixed connectors for I/O and Gigabit Ethernet applications in harsh environments

BS IEC 62946-02:2017 电子设备连接器. 频率为250 MHz及以下, 载流能力1 A及以下的数据传输用8路无屏蔽活动和固定式高密度连接器详细规格

Connectors for electronic equipment. Detail specification for 8-way, unshielded, free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with current carrying capacity up to 1 A

IEC 61076-2-113:2017 电子设备连接器. 产品要求. 第2-113部分: 圆形连接器. 频率为100 MHz及以下的数据传输用带M12螺钉锁功率和信号接口连接器详细规格

This part of IEC 61076 describes M12 circular connectors with two data pairs and power contacts with current ratings up to 12 A, that are typically used for data and power applications in industrial premises. These connectors consist of both fixed and free connectors either rewireable or non rewireable, with screw-locking. Male connectors have round contacts diameters of 1,50 mm, 1,00 mm and 0,60 mm. The different codings provided by this document prevent the mating of accordingly coded male or female connectors to any other similarly sized interfaces covered by other standards and the cross-mating between the different codings provided by this document. NOTE M12 is the dimension of the thread of the screw locking mechanism of these circular connectors.

Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz

BS EN 61076-3-120:2016 电子设备连接器. 产品要求. 矩形连接器. 直流额定电压250 V, 额定电流30 A的带弹簧锁可重接电源连接器详细规格

Connectors for electronic equipment. Product requirements. Rectangular connectors. Detail specification for rewirable power connectors with snap locking for rated voltage of 250 V d.c. and rated current of 30 A

BS EN 60603-7-82:2016 电子设备连接器. 频率为2000 MHz及以下的数据传输用8路12触点屏蔽活动和固定式连接器详细规格

Connectors for electronic equipment. Detail specification for 8-way, 12 contacts, shielded, free and fixed connectors, for data transmission with frequencies up to 2 000 MHz

IEC 62946-02:2017 电子设备连接器. 第02部分: 频率为250 MHz及以下, 载流能力1 A及以下的数据传输用8路无屏蔽活动和固定式高密度连接器详细规格

This part of IEC 62946 covers 8-way, unshielded free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with extra low voltage current carrying capabilities up to 1 A, and is intended to specify the common dimensions, mechanical, electrical, signal integrity and environmental characteristics and tests for these connectors.

Connectors for electronic equipment - Part 02: Detail specification for 8-way, unshielded, free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with current carrying capacity up to 1 A

BS EN 61076-3-110:2016 电子设备用连接器.产品要求.矩形连接器.频率小于3000 MHz的数据传输用活动和固定式连接器的详细规范

Connectors for electronic equipment. Product requirements. Detail specification for free and fixed connectors for data transmission with frequencies up to 3 000 MHz

EN 60603-7-82:2016 电子设备连接器 第 7-82 部分：8 路、12 触点、屏蔽、自由和固定连接器的详细规范，用于频率高达 2000 MHz 的数据传输

IEC 60603-7-82:2016 covers 8-way, 12 contacts, shielded, free and fixed connectors, references dimensional, mechanical, electrical and environmental characteristics and tests in IEC 60603-7-7, and specifies electrical transmission requirements, including power sum alien (exogenous) crosstalk, for frequencies up to 2 000 MHz. These connectors are typically used as "category 8.2" connectors in "class II" cabling systems specified in ISO/IEC TR 11801-9901 and specified in ISO/IEC 11801-1. These connectors are intermateable and interoperable with other IEC 60603-7 series connectors, i.e. as defined in IEC 60603-7-7 and IEC 60603-7-1. These connectors are backward compatible with other IEC 60603-7 series connectors. Key words: Connectors, 8-way. Shielded Free and Fixed, Data Transmission

Connectors for electronic equipment - Part 7-82: Detail specification for 8-way, 12 contacts, shielded, free and fixed connectors, for data transmission with frequencies up to 2 000 MHz