31.220.10 插头和插座装置、连接器 标准查询与下载

BS EN IEC 60352-5:2020 无焊连接 压入式连接 一般要求、测试方法和实践指导

What is BS EN IEC 60352 ‑ 5 about?    BS EN IEC 60352 ‑ 5 is the fifth part of the multi-series international standard on Solderless connection   BS EN IEC 60352 ‑ 5 applies to solderless press-in connections for use in electrical   and electronic equipment and components. The press-in connection consists of a termination having a suitable press-in zone that is inserted into a hole aboard.   Note: BS EN IEC 60352

Solderless connections - Press-in connections. General requirements, test methods and practical guidance

IEC 61076-2-114:2020 电气和电子设备用连接器.产品要求.第2-114部分:圆形连接器.带M8螺钉的连接器的详细规范.高达100MHz的数据传输用带电源触点和信号触点的锁定

Connectors for electrical and electronic equipment - Product requirements - Part 2-114: Circular connectors - Detail specification for connectors with M8 screw- locking with power contacts and signal

EN IEC 60352-5:2020 无焊连接 第5部分：压入式连接 一般要求、测试方法和实用指南

IEC 60352-5:2020 is applicable to solderless press-in connections for use in electrical and electronic equipment and components. The press-in connection consists of a termination having a suitable press-in zone which is inserted into a hole of a board. Information on materials and data from industrial experience is included in addition to the test procedures to provide electrically stable connections under specified environmental conditions. The object of this document is to determine the suitability of press-in connections under mechanical, electrical and atmospheric conditions as specified by the manufacturer of the press-in termination and to provide a means of comparing test results when the tools used to make the connections are of different designs or manufacture. This fifth edition cancels and replaces the fourth edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant changes with respect to the previous edition: revising the scope by removing the wording "… telecommunication equipment and in electronic devices employing similar techniques" and replacing it by "… electrical and electronic equipment and components" in the first paragraph; adding terms and definitions for 'board', 'hole' and 'metal board' to recognize that press-in terminations are being used in many non-printed board materials; editorial changes to clarify the difference between the two test schedules for qualification and application; modification of upper limit of copper thickness of the plated-through-hole to reflect actual market trends and manufacturing practices; removal of bending test, as this test is very specific for applications of press-in technology no longer common; adding graphs to document the press-in and push-out force, since this is common testing practice and provides further insight into mechanical performance of the contact zone; reducing the number of test specimens required, since in previous testing scheme a lot of test samples were discarded; new wording in 4.5 for cracked and bent terminations; added Figure 7b to show V and A connection locations when the press-in termination does not protrude through the bottom side of the board.

Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance

EN IEC 61076-2-012:2020 电气和电子设备用连接器 产品要求 第 2-012 部分：圆形连接器 根据 IEC 61076-2-101、IEC 61076-2-109、基于 M12 连接器接口的带内部推拉锁定的连接器的详细规范，

IEC 61076-2-012:2020 specifies circular connectors with an inner push‑pull locking mechanism of a size derived from and thus being compatible with M12 screw‑locking connectors and with mating interfaces according to IEC 61076‑2‑101, IEC 61076‑2‑109, IEC 61076‑2‑111 and IEC 61076‑2‑113. A female fixed connector with inner push-pull locking according to this document is intermateable with a correspondingly coded male free connector with M12 screw-locking according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 or IEC 61076-2-113. This document covers both: a) power connectors with current ratings up to 16 A and voltage ratings up to 630 V, typically used for power supply of electrical equipment used in industrial premises, and b) connectors for data and signal transmission with frequencies up to 500 MHz. These connectors consist of both fixed and free connectors, either rewirable or non‑rewirable, with M12 inner push‑pull locking as explained above. Male connectors have round contacts from Ø0,6 mm up to Ø1,5 mm. This document covers various types of connectors identified by their "codings" with different contact arrangement, not mutually interchangeable. The design of the inner push‑pull mechanism prevents the unintended mating of the male inner push‑pull free connector with the female connector with M12 screw‑locking even for identical coding. Some styles of free connectors with female contacts covered in this document are equipped with both inner and outer push-pull locking for intermateability also with correspondingly coded male fixed or free connectors according to IEC 61076-2-010.

Connectors for electrical and electronic equipment - Product Requirements - Part 2-012: Circular connectors - Detail specification for connectors with inner push-pull locking based on M12 connector interfaces according to IEC 61076-2-101, IEC 61076-2-109,

BS IEC 62946-01:2018 电气和电子设备连接器 矩形连接器 用于频率高达 100 MHz 且载流的数据传输的 8 路、屏蔽、自由和固定高密度连接器的详细规范...

1   Scope This part of IEC 62946 covers 8-way shielded connectors, and is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for the family of IEC 62946‑01 connectors. These connectors are intermateable and interoperable with other IEC 62946 series connectors.

Connectors for electrical and electronic equipment - Rectangular connectors. Detail specification for 8-way, shielded, free and fixed high density connectors for data transmission with frequencies up to 100 MHz and with current carrying…

IEC 61076-2-012:2020 电气和电子设备用连接器.产品要求.第2-012部分:圆形连接器.根据IEC 61076-2-101 IEC 61076-2-109 IEC 61076-2-111和IEC 61076-2-113的基于M12连接器接口的内推拉锁定连接器详细规范

Connectors for electrical and electronic equipment - Product Requirements - Part 2-012: Circular connectors - Detail specification for connectors with inner push-pull locking based on M12 connector in

IEC 60352-5:2020 无焊接 - 第5部分:压入式连接 - 一般要求 测试方法和实践指导

Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance

IEC PAS 61076-2-010:2020 电气和电子设备用连接器.产品要求.第2-010部分:圆形连接器.基于符合IEC 61076-2-101 IEC 61076-2-109 IEC 61076-2-111和IEC 61076-2-113的匹配接口的带锁紧机构的推拉连接器详细规范

Connectors for electrical and electronic equipment - Product requirements - Part 2-010: Circular connectors - Detail specification for push-pull connectors with locking mechanism, based on mating inte

BS EN IEC 61076-8-101:2020 电气和电子设备连接器 产品要求 电源连接器 额定电流为 40 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封塑料外壳连接器的详细规范

What is BS EN IEC 61076 ‑ 8 ‑ 101 about? BS EN IEC 61076 ‑ 8 ‑ 101 is the eighth part of Connectors for electrical and electronic equipment in multi-series. BS EN IEC 61076 ‑ 8 ‑ 101 describes 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with a plastic housing (hereinafter referred to as a connector) for electrical and electronic equipment, including overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods. BS EN IEC 61076 ‑ 8 ‑ 101 applies to electrical connectors with sealing and shielding requirements meeting this document, with a rated voltage up to and including 750 V a.c. or 1 000 V d.c. and a current rating of 40 A, in the field of electrical and electronic equipment. Who is BS EN IEC 61076 ‑ 8 ‑

Connectors for electrical and electronic equipment. Product requirements - Power connectors. Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 40 A

BS EN IEC 61076-8-100:2020 电气和电子设备连接器 产品要求 电源连接器 额定电流为 20 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封塑料外壳连接器的详细规范

What is BS EN IEC 61076 ‑ 8 ‑ 100 about? BS EN IEC 61076 ‑ 8 ‑ 100 is the eighth part of Connectors for electrical and electronic equipment in multi-series. BS EN IEC 61076 ‑ 8 ‑ 100 describes 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with a plastic housing (hereinafter referred to as a connector) for electrical and electronic equipment, including overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods. Who is BS EN IEC 61076 ‑ 8 ‑ 100 for ? BS EN IEC 61076 ‑ 8 ‑ 100 on Connectors for electrical and electronic equipment is useful for: Manufacturer of electronic devices Sound engineers Manufacturers and distributors of connectors Electrical engineers Why should you use BS EN IEC 61076 ‑ 8 ‑ 100? Electric connectors are electromechanical devices used to join electronic conductors. These connectors are used in creating electronic circuits. BS EN IEC 61076 ‑ 8 ‑ 100 will help you in classifying the electrical characteristics and help in contact resistance and insulation resistance. Using standard copper wire in connectors, these connectors can sustain in different climatic conditions. BS EN IEC 61076

Connectors for electrical and electronic equipment. Product requirements - Power connectors. Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 20 A

BS EN IEC 61076-8-102:2020 电气和电子设备连接器 产品要求 电源连接器 额定电流为 150 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封塑料外壳连接器的详细规范

What is BS EN IEC 61076 ‑ 8 ‑ 102 about ?    BS EN IEC 61076 ‑ 8 ‑ 102 is the eighth part of connectors for electrical and electronic equipment in multi-series.   BS EN IEC 61076 ‑ 8 ‑

Connectors for electrical and electronic equipment. Product requirements - Power connectors. Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 150 A

EN IEC 61076-8-102:2020 电气和电子设备用连接器 产品要求 第 8-102 部分：电源连接器 额定电流为 150 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封塑料外壳连接器的详细规范

IEC 61076-8-102:2020 describes 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing (hereinafter referred to as a connector) for electrical and electronic equipment, including overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods. This document is applicable to electrical connectors with sealing and shielding requirements meeting this document, with a rated voltage up to and including 750 V a.c. or 1 000 V d.c., and a current rating of 150 A, for applications in the field of electrical and electronic equipment.

Connectors for electrical and electronic equipment - Product requirements - Part 8-102: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 150 A

EN IEC 61076-8-100:2020 电气和电子设备连接器 产品要求 第 8-100 部分：电源连接器 额定电流 20 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封塑料外壳连接器的详细规范

IEC 61076-8-100:2020 describes 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing (hereinafter referred to as a connector) for electrical and electronic equipment, including overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods. This document is applicable to electrical connectors with sealing and shielding requirements meeting this document, with a rated voltage up to and including 750 V a.c. or 1 000 V d.c. and a current rating of 20 A, for applications in the field of electrical and electronic equipment.

Connectors for electrical and electronic equipment - Product requirements - Part 8-100: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 20 A

EN IEC 63171-1:2020 电气和电子设备连接器 第1部分：双向、屏蔽或非屏蔽、自由和固定连接器的详细规范 机械配合信息、引脚分配和 1 类铜 LC 型的附加要求

IEC 63171-1:2020 covers two-way, shielded or unshielded, free and fixed connectors for data transmission with frequencies up to 600 MHz and with current carrying capacity up to 2,0 A at 60 °C. It is intended to specify the common dimensions, mechanical, electrical, signal integrity, environmental characteristics, reliability specifications and corresponding tests for these connectors.

Connectors for electrical and electronic equipment - Part 1: Detail specification for two-way, shielded or unshielded, free and fixed connectors - Mechanical mating information, pin assignment and additional requirements for Type 1 copper LC style

EN IEC 61076-8-101:2020 电气和电子设备用连接器 产品要求 第 8-101 部分：电源连接器 额定电流为 40 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封塑料外壳连接器的详细规范

IEC 61076-8-101:2020 describes 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing (hereinafter referred to as a connector) for electrical and electronic equipment, including overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods. This document is applicable to electrical connectors with sealing and shielding requirements meeting this document, with a rated voltage up to and including 750 V a.c. or 1 000 V d.c. and a current rating of 40 A, in the field of electrical and electronic equipment.

Connectors for electrical and electronic equipment - Product requirements - Part 8-101: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 40 A

IEC 61076-8-102:2020 电子设备连接器 - 产品要求 - 第8-102部分:电源连接器 - 2P或3P电源加2P信号屏蔽和密封连接器的详细规范 带塑料外壳 额定电流为150 A

Connectors for electrical and electronic equipment - Product requirements - Part 8-102: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connec

IEC 63171-1:2020 电气和电子设备用连接器第1部分:双向、屏蔽或非屏蔽、自由和固定连接器详细规范第1类铜LC型机械配合信息、插针分配和附加要求

Connectors for electrical and electronic equipment - Part 1: Detail specification for two-way, shielded or unshielded, free and fixed connectors - Mechanical mating information, pin assignment and add

IEC 61076-8-100:2020 电气和电子设备用连接器.产品要求.第8-100部分:电源连接器.额定电流为20A的塑料外壳2极或3极电源加2极信号屏蔽和密封连接器详细规范

Connectors for electrical and electronic equipment - Product requirements - Part 8-100: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connec

IEC 61076-8-101:2020 电气和电子设备用连接器.产品要求.第8-101部分:电源连接器.额定电流为40A的塑料外壳的2极或3极电源加2极信号屏蔽和密封连接器详细规范

Connectors for electrical and electronic equipment - Product requirements - Part 8-101: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connec

EN IEC 63171-6:2020 电气和电子设备连接器 第6部分：用于频率高达 600 MHz 的电源和数据传输的 2 路和 4 路（数据/电源）屏蔽、自由和固定连接器的详细规范

IEC 63171-6:2020, covers 2-way and 4-way (data/power) shielded free and fixed connectors for data transmission with frequencies up to 600 MHz and specifies the common dimensions, mechanical, electrical and transmission characteristics and environmental requirements as well as test specifications respectively. This document specifies several properties overlapping with specifications in the IEC 63171 series which have been drafted later. In case of conflict the specifications within this document prevail. Keywords: Connectors for data transmission

Connectors for electrical and electronic equipment - Part 6: Detail specification for 2-way and 4-way (data/power), shielded, free and fixed connectors for power and data transmission with frequencies up to 600 MHz.