71.040.50 物理化学分析方法 标准查询与下载

ASTM E1829-14(2020) 表面分析前处理标本的标准指南

1.1 This guide covers specimen handling and preparation prior to surface analysis and applies to the following surface analysis disciplines: 1.1.1 Auger electron spectroscopy (AES), 1.1.2 X-ray photoelectron spectroscopy (XPS or ESCA), and 1.1.3 Secondary ion mass spectrometry (SIMS). 1.1.4 Although primarily written for AES, XPS, and SIMS, these methods may also apply to many surface-sensitive analysis methods, such as ion scattering spectrometry, lowenergy electron diffraction, and electron energy loss spectroscopy, where specimen handling can influence surfacesensitive measurements. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Handling Specimens Prior to Surface Analysis

ASTM E984-12(2020) 识别俄歇电子能谱中化学效应和基质效应的标准指南

1.1 This guide outlines the types of chemical effects and matrix effects which are observed in Auger electron spectroscopy. 1.2 Guidelines are given for the reporting of chemical and matrix effects in Auger spectra. 1.3 Guidelines are given for utilizing Auger chemical effects for identification or characterization. 1.4 This guide is applicable to both electron excited and X-ray excited Auger electron spectroscopy. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Identifying Chemical Effects and Matrix Effects in Auger Electron Spectroscopy

ASTM E2735-14(2020) 用于选择X射线光电子能谱所需校准的标准指南

1.1 This guide describes an approach to enable users and analysts to determine the calibrations and standards useful to obtain meaningful surface chemistry data with X-ray photoelectron spectroscopy (XPS) and to optimize the instrument for specific analysis objectives and data collection time. 1.2 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide will be applicable in all circumstances. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection of Calibrations Needed for X-ray Photoelectron Spectroscopy (XPS) Experiments

ASTM E1078-14(2020) 标本制备和表面分析安装标准指南

1.1 This guide covers specimen preparation and mounting prior to, during, and following surface analysis and applies to the following surface analysis disciplines: 1.1.1 Auger electron spectroscopy (AES), 1.1.2 X-ray photoelectron spectroscopy (XPS and ESCA), and 1.1.3 Secondary ion mass spectrometry (SIMS). 1.1.4 Although primarily written for AES, XPS, and SIMS, these methods will also apply to many surface sensitive analysis methods, such as ion scattering spectrometry, low energy electron diffraction, and electron energy loss spectroscopy, where specimen handling can influence surface sensitive measurements. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Specimen Preparation and Mounting in Surface Analysis

ASTM C1647-20 用于铀或钚的铀或钚或两者的铀或钚材料中的杂质测定的标准操作

1.1 This practice covers instructions for using an extraction chromatography column method for the removal of plutonium or uranium, or both, from liquid or digested oxides or metals prior to impurity measurements. Quantification of impurities can be made by techniques such as inductively coupled plasma mass spectrometry (ICP-MS), inductively coupled plasma atomic emission spectrometry (ICP-AES), or atomic absorption spectrometry (AAS.) 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Removal of Uranium or Plutonium, or both, for Impurity Assay in Uranium or Plutonium Materials

ASTM D6733-01(2020) 通过50米毛细管高分辨率气相色谱法测定火花点火发动机燃料中各个组分的标准测试方法

1.1 This test method covers the determination of individual hydrocarbon components of spark-ignition engine fuels with boiling ranges up to 225 °C. Other light liquid hydrocarbon mixtures typically encountered in petroleum refining operations, such as, blending stocks (naphthas, reformates, alkylates, and so forth) may also be analyzed; however, statistical data was obtained only with blended spark-ignition engine fuels. The tables in Annex A1 enumerate the components reported. Component concentrations are determined in the range from 0.10 % to 15 % by mass. The procedure may be applicable to higher and lower concentrations for the individual components; however, the user must verify the accuracy if the procedures are used for components with concentrations outside the specified ranges. 1.2 This test method is applicable also to spark-ignition engine fuel blends containing oxygenated components. However, in this case, the oxygenate content must be determined by Test Methods D5599 or D4815. 1.3 Benzene co-elutes with 1-methylcyclopentene. Benzene content must be determined by Test Method D3606 or D5580. 1.4 Toluene co-elutes with 2,3,3-trimethylpentane. Toluene content must be determined by Test Method D3606 or D5580. 1.5 Although a majority of the individual hydrocarbons present are determined, some co-elution of compounds is encountered. If this procedure is utilized to estimate bulk hydrocarbon group-type composition (PONA) the user of such data should be cautioned that error may be encountered due to co-elution and a lack of identification of all components present. Samples containing significant amounts of naphthenic (for example, virgin naphthas) constituents above n-octane may reflect significant errors in PONA type groupings. Based on the interlaboratory cooperative study, this procedure is applicable to samples having concentrations of olefins less than 20 % by mass. However, significant interfering coelution with the olefins above C7 is possible, particularly if blending components or their higher boiling cuts such as those derived from fluid catalytic cracking (FCC) are analyzed, and the total olefin content may not be accurate. Many of the olefins in spark ignition fuels are at a concentration below 0.10 %; they are not reported by this test method and may bias the total olefin results low. 1.5.1 Total olefins in the samples may be obtained or confirmed, or both, by Test Method D1319 (volume %) or other test methods, such as those based on multidimensional PONA type of instruments. 1.6 If water is or is suspected of being present, its concentration may be determined, if desired, by the use of Test Method D1744. Other compounds containing sulfur, nitrogen, and so forth, may also be present, and may co-elute with the hydrocarbons. If determination of these specific compounds is required, it is recommended that test methods for these specific materials be used, such as Test Method D5623 for sulfur compounds. 1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricantsand is the direct responsibility of Subcommittee D02.04.0L on Gas Chromatography Methods. Current edition approved Nov. 1, 2020. Published November 2020. Originally approved in 2001. Last previous edition approved in 2016 as D6733 – 01 (2016). DOI: 10.1520/D6733-01R20. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 2. Referenced Documents

Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography

ASTM C1510-01(2020) 通过研磨分光光度法测定白色颜色和色差的标准测试方法

1.1 This test method describes the instrumental measurement of the reflection properties and color of ceramic glazes and other whitewares by the use of a spectrophotometer or spectrocolorimeter with a hemispherical optical measuring system, such as an integrating sphere. 1.2 The test method is suitable for use with most specimens having an exterior flat surface large enough to cover the spectrophotometer sample port. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Color and Color Difference of Whitewares by Abriged Spectrophotometry

ASTM E2409-20a 单 - 二 - 三 - 和四乙二醇和单 - 和二 - 丙二醇中乙二醇杂质的标准测试方法（气相色谱法）

1.1 This test method describes the gas chromatographic determination of glycol impurities in Mono-, Di-, Tri-, and Tetraethylene Glycol (MEG, DEG, TEG, and TetraEG), and in Monoand Dipropylene Glycol (MPG and DPG). 1.2 This test method is applicable to MEG, DEG, TEG, and TetraEG with impurities to 3000 mg/kg. The limit of detection (LOD) is 22 mg/kg and the limit of quantitation (LOQ) is 73 mg/kg. NOTE 1—LOD and LOQ were calculated using the lowest level sample in the ILS. 1.3 This test method is applicable to MPG and DPG to

Standard Test Method for Glycol Impurities in Mono-, Di-, Tri- and Tetraethylene Glycol and in Mono- and Dipropylene Glycol(Gas Chromatographic Method)

DB13/T 5220-2020 合成材料跑道面层中铅、镉、铬、汞的测定 X射线荧光光谱法

Determination of lead, cadmium, chromium, mercury in synthetic runway surfaces - X-ray fluorescence spectrometry

DB13/T 5219-2020 合成材料面层健身步道技术规范

Technical specifications for fitness walkways with synthetic material surfaces

ASTM E1792-20 表面灰尘铅取样材料的标准规格

1.1 This specification covers requirements for wipes that are used to collect settled dusts on surfaces for the subsequent determination of lead. 1.2 For wipe materials used for the determination of beryllium in surface dust refer to Specification D7707. This is mentioned to insure that users of wipes recognize that there is some relationship between the analytical backgrounds found in wipes and the analyte of interest. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wipe Sampling Materials for Lead in Surface Dust

ASTM E1726-20 通过热板消解制备土壤样品以进行后续铅分析的标准实践

Standard Practice for Preparation of Soil Samples by Hotplate Digestion for Subsequent Lead Analysis

ASTM E1775-20 现场提取和现场便携式电化学或铅分光光度分析性能评估标准指南

1.1 This guide provides guidelines for determining the performance of field-portable quantitative lead analysis instruments. 1.2 This guide applies to field-portable electroanalytical and spectrophotometric (including reflectance and colorimetric) analyzers. 1.3 Sample matrices of concern herein include paint, dust, soil, and airborne particles. 1.4 This guide addresses the desired performance characteristics of field-based sample extraction procedures for lead, as well as on-site extraction followed by field-portable analysis. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluating Performance of On-Site Extraction and Field-Portable Electrochemical or Spectrophotometric Analysis for Lead

ISO/TS 23973:2020 临界条件下的液相色谱法 聚乙烯氧化物的化学不均匀性

Liquid chromatography at critical conditions (LCCC) — Chemical heterogeneity of polyethylene oxides

BS ISO 13067:2020 微束分析 电子背散射衍射 平均晶粒尺寸的测量

What is ISO 13067 about?   ISO 13067 is an international standard that discusses microbeam analysis for electron backscatter diffraction. ISO 13067 specifies the procedures for measuring average grain size derived from a two- dimensional polished cross-section using backscatter diffraction (EBSD).   ISO 13067 requires the measurement of orientation, disorientation and pattern quality factor as a function of position in the crystalline specimen.   Who is ISO 13067 for?   ISO 13067 on electron backscatter diffraction is useful for:

Microbeam analysis. Electron backscatter diffraction. Measurement of average grain size

ASTM UOP905-20 通过 X 射线衍射的铂团聚

This method is for the qualitative identification of the presence of platinum agglomeration and types of alumina in reforming catalysts using X-ray diffraction. These materials generally contain between 0.2 to 0.4 mass-% platinum on predominantly gamma-alumina support. Catalyst samples may be either fresh, spent or regenerated, as typical levels of carbon, sulfur and moisture associated with these samples do not interfere. Reforming catalysts containing less than 2% zeolitic materials may also be analyzed. Platinum alloys with other metals such as tin, rhodium, rhenium or iron can also be identified by displacement of the Pt peak from expected position. If this occurs, additional types of analysis such as STEM can be used to identify the type of alloy if needed. Refer to the Appendix for quantification of Pt agglomeration.

Platinum Agglomeration by X-Ray Diffraction

ASTM D7951-20 歧化（TDP）甲苯的标准规范

1.1 This specification covers Disproportionation (TDP) toluene. 1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Consult current OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Disproportionation (TDP) Toluene

ASTM E2409-20 单 - 二 - 三 - 和四乙二醇和单 - 和二 - 丙二醇中乙二醇杂质的标准测试方法（气相色谱法）

Standard Test Method for Glycol Impurities in Mono-, Di-, Tri- and Tetraethylene Glycol and in Mono- and Dipropylene Glycol(Gas Chromatographic Method)

ISO 13067:2020 微束分析 - 电子反向散射衍射 - 平均晶粒尺寸的测量

This document describes procedures for measuring average grain size derived from a two-dimensional polished cross-section using electron backscatter diffraction (EBSD). This requires the measurement of orientation, misorientation and pattern quality factor as a function of position in the crystalline specimen[1]. The measurements in this document are made on two dimensional sections. The reader should note carefully the definitions used (3.3) which draw a distinction between the measured sectional grain sizes, and the mean grain size which can be derived from them that relates to the three dimensional grain size. NOTE 1 While conventional methods for grain size determination using optical microscopy are well- established, EBSD methods offer a number of advantages over these techniques, including increased spatial resolution and quantitative description of the orientation of the grains. NOTE 2 The method also lends itself to the measurement of the grain size of complex materials, for example those with a significant duplex content. NOTE 3 The reader is warned to interpret the results with care when attempting to investigate specimens with high levels of deformation.

Microbeam analysis — Electron backscatter diffraction — Measurement of average grain size

T/CSTM 00340-2020 石墨烯粉体材料中碳、氢、氧、氮、硫元素含量的测定方法 元素分析仪法

本标准规定了使用元素分析仪法测定单层或多层石墨烯粉体材料中碳、氢、氧、氮、硫元素含量的概述、仪器及试剂材料、取样、测试准备、测试结果计算、检测报告和精密度等。 本标准适用于单层或多层石墨烯粉体材料中总碳、总氢、总氧、总氮、总硫含量的测定。

Determination of the carbon, hydrogen, oxygen, nitrogen, and sulfur content of graphene powder materials— Elemental analyzer method