75.180.01 石油和天然气工业设备综合 标准查询与下载

T/QGCML 2267-2023 低浓度煤层气浓缩制压缩天然气压缩净化系统

本文件规定了低浓度煤层气浓缩制压缩天然气压缩净化系统的术语和定义、系统构成及原理、一般要求、工艺流程、操作与控制、系统巡检。 本文件适用于低浓度煤层气浓缩制压缩天然气压缩净化系统的操作与控制。

Low-concentration coalbed methane concentration to produce compressed natural gas compression and purification system

T/QGCML 2268-2023 低浓度煤层气浓缩制压缩天然气压缩系统

本文件规定了低浓度煤层气浓缩制压缩天然气压缩系统的术语和定义、系统构成及原理、技术要求、工艺流程、系统操作、系统巡检。 本文件适用于低浓度煤层气浓缩制压缩天然气压缩系统的操作与控制。

Low-concentration coalbed methane enrichment and compressed natural gas compression system

T/QGCML 2266-2023 低浓度煤层气浓缩制压缩天然气冷却塔系统

本文件规定了低浓度煤层气浓缩制压缩天然气冷却塔系统的术语和定义、系统构成及原理、一般要求、工艺流程、操作与控制、系统巡检。 本文件适用于低浓度煤层气浓缩制压缩天然气冷却塔系统的操作与控制。

Low-concentration coalbed methane concentration to produce compressed natural gas cooling tower system

T/CSTM 00402-2023 油气集输用缓蚀剂性能及试验评价方法

本文件规定了油气集输用缓蚀剂的术语和定义、性能指标、理化性能评价、腐蚀速率及缓蚀率测定试验、试验报告等。 本文件适用于油气田集输管线用缓蚀剂的筛选和评价。

Performance and evaluation methods of corrosion inhibitor for oil and gas gathering system

T/QGCML 1970-2023 压裂泵

本文件规定了压裂泵的术语和定义、常用计算公式、型号编制规则、泵方向及液缸号规定、信息确认、主要零部件、要求、主要零部件材料、焊接、检测、试验、标志和表面保护，出厂文件、贮存、包装和运输要求及使用规范。 本标准适用于压裂泵的生产和检验。

fracturing pump

GSO ISO 15156-2:2023 石油和天然气工业 石油和天然气生产中含 H2S 环境中使用的材料 第2部分：抗裂碳钢和低合金钢以及铸铁的使用

This document gives requirements and recommendations for the selection and qualification of carbon and low-alloy steels for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments, whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards or regulations. This document addresses the resistance of these steels to damage that can be caused by sulfide stress cracking (SSC) and the related phenomena of stress-oriented hydrogen-induced cracking (SOHIC) and soft-zone cracking (SZC). This document also addresses the resistance of these steels to hydrogen-induced cracking (HIC) and its possible development into stepwise cracking (SWC). This document is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed. Table 1 provides a non-exhaustive list of equipment to which this document is applicable, including exclusions. This document applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, see ISO 15156-1:2020, Clause 5. Annex A lists SSC-resistant carbon and low alloy steels, and A.2.4 includes requirements for the use of cast irons. This document is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.

Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons

GSO ISO 15156-3:2023 石油和天然气工业 石油和天然气生产中含 H2S 环境中使用的材料 第3部分：抗裂 CRA（耐腐蚀合金）和其他合金

This document gives requirements and recommendations for the selection and qualification of CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards, or regulations. This document addresses the resistance of these materials to damage that can be caused by sulfide stress cracking (SSC), stress corrosion cracking (SCC), and galvanically induced hydrogen stress cracking (GHSC). This document is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed. Table 1 provides a non-exhaustive list of equipment to which this document is applicable, including exclusions. This document applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, see ISO 15156‑1:2020, Clause 5. This document is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.

Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys

GSO ISO 15156-1:2023 石油和天然气工业 石油和天然气生产中含 H2S 环境中使用的材料 第1部分：抗裂材料选择的一般原则

This document describes general principles and gives requirements and recommendations for the selection and qualification of metallic materials for service in equipment used in oil and gas production and in natural-gas sweetening plants in H2S-containing environments, where the failure of such equipment can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements given in the appropriate design codes, standards, or regulations. This document addresses all mechanisms of cracking that can be caused by H2S, including sulfide stress cracking, stress corrosion cracking, hydrogen-induced cracking and stepwise cracking, stress-oriented hydrogen-induced cracking, soft zone cracking, and galvanically induced hydrogen stress cracking. Table 1 provides a non-exhaustive list of equipment to which this document is applicable, including exclusions. This document applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, see Clause 5. This document is not necessarily applicable to equipment used in refining or downstream processes and equipment.

Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 1: General principles for selection of cracking-resistant materials

ISO/DIS 23936-4:2023 包括低碳能源在内的石油和天然气工业 与石油和天然气生产相关介质接触的非金属材料 第 4 部分：纤维增强复合材料

Oil and gas industries including lower carbon energy — Non-metallic materials in contact with media related to oil and gas production — Part 4: Fiber-reinforced composite

23/30474665 DC BS ISO 16904-2 液化天然气安装和设备 船舶输送系统的设计和测试 第2部分：输送软管的设计和测试

BS ISO 16904-2. Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems - Part 2. Design and testing of transfer hoses

ISO/CD 23936-4:2023 包括低碳能源在内的石油和天然气工业 与石油和天然气生产相关介质接触的非金属材料 第 4 部分：纤维增强复合材料

Oil and gas industries including lower carbon energy — Non-metallic materials in contact with media related to oil and gas production — Part 4: Fiber-reinforced composite

T/CPCIF 0260-2023 非液化烃双防罐罐区设计规范

本文件规定了非液化烃双防罐罐区的设计要求。 本文件适用于新建、扩建或改建非液化烃双防罐罐区的设计。

Code for design of double containment storage tank farm for non-liquefied hydrocarbon

T/NXQICA 01-2022 危险化学品立式金属储罐安全技术规范

1、危险化学品立式金属常压储罐设计载荷　 2、危险化学品立式金属常压储罐用材料　 3、危险化学品立式金属常压储罐设计　 4、危险化学品立式金属常压储罐制造　 5、危险化学品立式金属常压储罐工程验收　 6、危险化学品立式金属常压储罐定期检验　 7、危险化学品立式金属常压储罐缺陷处理　 8、危险化学品立式金属常压储罐 检验结论　 9、危险化学品立式金属常压储罐安全附件及仪表　 附   录  A（资料性）定期检验铭牌　 附   录  B（资料性）危险化学品名称及其临界量　 附   录  C（资料性）立式圆筒形钢制焊接储罐对基础的基本要求　 附   录  D（资料性）危险化学品储罐定期检验工作联络单　 附   录  E（资料性）危险化学品储罐定期检验（委托检验）报告　

Safety technical specification for vertical metal storage tank of hazardous chemicals

T/CAS ES370112008-2022 工业品质量分级评价规则 电子式井下压力计

1　范围  本文件规定了电子式井下压力计质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于电子式井下压力计的质量评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 SY/T 5134  石油勘探开发仪器基本环境试验方法 试验G SY/T 5221  石油勘探开发仪器基本环境试验方法 试验B SY/T 6640  电子式井下压力计校准方法 JJG 1173  电子式井下压力计检定规程 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则 通则

Rules for quality grading and evaluating of industrial products—Electronic downhole pressure gauge

T/CAS ES371900003-2022 工业品质量分级评价规则 油气回收在线监控系统

1　范围 本文件规定了油气回收在线监控系统质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于油气回收在线监控系统、质量分级评价活动；同时本文件也适用便携式油气回收监控系统。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB 20952—2020  加油站大气污染物排放标准 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则 通则

Rules for quality grading and evaluating of industrial products—Oil and gas recovery online monitoring system

ISO/TS 16901:2022 陆上液化天然气装置（包括船/岸界面）设计中的风险评估指南

Guidance on performing risk assessment in the design of onshore LNG installations including the ship/shore interface

BS EN ISO 23936-1:2022 石油和天然气行业 包括低碳能源 与石油和天然气生产相关的介质接触的非金属材料 热塑性塑料

1   Scope This document gives general principles, specifies requirements and gives recommendations for the assessment of the stability of non-metallic materials for service in equipment used in oil and gas exploration and production environments. This information aids in material selection. It can be applied to help avoid costly degradation failures of the equipment itself, which could pose a risk to the health and safety of the public and personnel or the environment. This document also provides guidance for quality assurance. It supplements but does not replace, the material requirements given in the appropriate design codes, standards or regulations. This document addresses the resistance of thermoplastics to the deterioration in properties that can be caused by physical or chemical interaction with produced and injected oil and gas-field media, and with chemical treatment. Interaction with sunlight and ionizing radiation are excluded from the scope of this document. This document is not necessarily suitable for application to equipment used in refining or downstream processes and equipment. The equipment considered includes, but is not limited to, non-metallic pipelines, piping, liners, seals, gaskets and washers. Blistering by rapid gas decompression is not included in the scope of this document. This document applies to the assessment of the stability of non-metallic materials in simulated hydrocarbon production conditions to aid the selection of materials for equipment designed and constructed using conventional design criteria. Designs utilizing other criteria are excluded from its scope.

Oil and gas industries including lower carbon energy. Non-metallic materials in contact with media related to oil and gas production. Thermoplastics

T/NTAS 013-2022 多用液压动力钳

本文件规定了多用液压动力钳的分类、要求、试验方法、检验规则、标志、包装和贮存。 本文件适用于多用液压动力钳的设计、制造和检验。

Multipurpose hydraulic power tongs

EN ISO 23936-1:2022 石油,石化和天然气工业.与油和气生产有关的介质接触的非金属材料.第1部分:热塑性塑料

This document gives general principles, specifies requirements and gives recommendations for the assessment of the stability of non-metallic materials for service in equipment used in oil and gas exploration and production environments. This information aids in material selection. It can be applied to help avoid costly degradation failures of the equipment itself, which could pose a risk to the health and safety of the public and personnel or the environment. This document also provides guidance for quality assurance. It supplements but does not replace, the material requirements given in the appropriate design codes, standards or regulations. This document addresses the resistance of thermoplastics to the deterioration in properties that can be caused by physical or chemical interaction with produced and injected oil and gas-field media, and with chemical treatment. Interaction with sunlight and ionizing radiation are excluded from the scope of this document. This document is not necessarily suitable for application to equipment used in refining or downstream processes and equipment. The equipment considered includes, but is not limited to, non-metallic pipelines, piping, liners, seals, gaskets and washers. Blistering by rapid gas decompression is not included in the scope of this document. This document applies to the assessment of the stability of non-metallic materials in simulated hydrocarbon production conditions to aid the selection of materials for equipment designed and constructed using conventional design criteria. Designs utilizing other criteria are excluded from its scope.

Oil and gas industries including lower carbon energy - Non-metallic materials in contact with media related to oil and gas production - Part 1: Thermoplastics (ISO 23936-1:2022)

T/CI 080-2022 管体缺陷智能套筒修复技术规范

智能套筒修复技术 epoxy injection technology for sleeve 主要用于各类钢质管道缺陷的承压强度的恢复。对于此类缺陷，采用钢制套筒安装在管道缺陷的外表面，与管道保持一定环缝隙，环缝隙两端用胶封闭，再在此封闭空间内灌注环氧填胶，构成复合套管，对管道缺陷进行补强。智能套筒内壁预留应变计安装槽，用于后期应变计安装，实现对管体缺陷及环氧填充剂的应力监测。 3.2　 套筒 sleeve 管体缺陷智能套筒修复技术中所用的套筒可以套在钢制管道上，管道和套筒之间注入环氧。套筒包括焊接式和法兰式两种。 3.3　 环氧树脂 epoxy resin 修复注入用环氧树脂材料由基料和固化剂按一定比例混合而成。其中基料组分包括：环氧树脂、改性橡胶弹性体、环氧改性聚氨酯弹性体、经偶联剂处理过的无机填料、气相法二氧化硅。固化剂部分包括：改性脂环族胺类固化剂、聚酰胺类固化剂、改性脂肪族胺类固化剂。 3.4　 缺陷修补填平胶 glue for repairing and leveling defects 在缺陷处涂抹缺陷修补填平胶可以缓解应力集中。主要包括：环氧树脂、硅灰石、活性稀释剂、增塑剂、胺固化剂。 3.5　 缺陷 defect 管道超出可接受标准的不完整类型或量级。 3.6　 修复压力 repair pressure 实施修复时缺陷处管道的操作压力。 3.7　 凹陷 dent 管壁受外部挤压或碰撞产生径向位移而形成的局部塌陷，是由于管壁永久塑性变形而使管道横截面发生的形状改变。 3.8　 应力 stress 作用于单位面积上的载荷或力。 4　补强应具备的资料 4.1　管道资料调查 4.1.1　原始资料 管道管径、壁厚及使用年限。 4.1.2　管道运行记录 管道输送介质、压力、温度等。 4.1.3　管道维修或改造资料 管道维修记录及竣工资料。

Technical specification for intelligent sleeve repair of pipe defects