75.180.01 石油和天然气工业设备综合 标准查询与下载

ISO 15156-1:2020 石油和天然气工业.石油和天然气生产中用于含H2S环境的材料.第1部分:选择抗裂材料的一般原则

This document describes general principles and gives requirements and recommendations for the selection and qualification of metallic materials for service in equipment used in oil and gas production and in natural-gas sweetening plants in H2S-containing environments, where the failure of such equipment can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements given in the appropriate design codes, standards, or regulations. This document addresses all mechanisms of cracking that can be caused by H2S, including sulfide stress cracking, stress corrosion cracking, hydrogen-induced cracking and stepwise cracking, stress-oriented hydrogen-induced cracking, soft zone cracking, and galvanically induced hydrogen stress cracking. Table 1 provides a non-exhaustive list of equipment to which this document is applicable, including exclusions. This document applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, see Clause 5. This document is not necessarily applicable to equipment used in refining or downstream processes and equipment.  Table 1 — List of equipment This document is applicable to materials used for the following equipment Exclusions Drilling, well construction, and well-servicing equipment Equipment exposed only to drilling fluids of controlled compositiona Drill bits Blowout preventer (BOP) shear bladesb Drilling riser systems Work strings Wireline and wireline equipmentc Surface and intermediate casing Wells, including subsurface equipment, gas-lift equipment, wellheads, and christmas trees Sucker rod pumps and sucker rodsd Electric submersible pumps Other artificial lift equipment Slips Flowlines, gathering lines, field facilities, and field processing plants Crude-oil storage and handling facilities operating at a total absolute pressure below 0,45 MPa (65 psi) Water-handling equipment Water-handling facilities operating at a total absolute pressure below 0,45 MPa (65 psi) Water injection and water disposal equipment Natural-gas treatment plants — Transportation pipelines for liquids, gases, and multiphase fluids Lines handling gas prepared for general commercial and domestic use For all equipment above Components loaded only in compression a See ISO 15156-2:2020, A.2.3.2.3 for more information. b See ISO 15156-2:2020, A.2.3.2.1 for more information. c Wireline lubricators and lubricator connecting devices are not excluded. d For sucker rod pumps and sucker rods, reference can be made to NACE MR0176.

Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 1: General principles for selection of cracking-resistant materials

ISO 15156-3:2020 石油和天然气工业 - 用于石油和天然气生产中含H2S的环境中的材料 - 第2部分:耐开裂碳和低合金钢以及铸铁的使用

This document gives requirements and recommendations for the selection and qualification of CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards, or regulations. This document addresses the resistance of these materials to damage that can be caused by sulfide stress cracking (SSC), stress corrosion cracking (SCC), and galvanically induced hydrogen stress cracking (GHSC). This document is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed. Table 1 provides a non-exhaustive list of equipment to which this document is applicable, including exclusions. This document applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, This document is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.  Table 1 — List of equipment This document is applicable to materials used for the following equipment Exclusions Drilling, well construction, and well-servicing equipment Equipment exposed only to drilling fluids of con- trolled compositiona Drill bits Blowout-preventer (BOP) shear bladesb Drilling riser systems Work strings Wireline and wireline equipmentc Surface and intermediate casing Wells including subsurface equipment, gas lift equipment, wellheads, and christmas trees Sucker rod pumps and sucker rodsd Electric submersible pumps Other artificial lift equipment Slips Flow-lines, gathering lines, field facilities, and field processing plants Crude oil storage and handling facilities operating at a total absolute pressure below 0,45 MPa (65 psi) Water-handling equipment Water-handling facilities operating at a total absolute pressure below 0,45 MPa (65 psi) Water injection and water disposal equipment Natural gas treatment plants — Transportation pipelines for liquids, gases, and multi-phase fluids Lines handling gas prepared for general commer- cial and domestic use For all equipment above Components loaded only in compression a See ISO 15156-2:2020, A.2.3.2.3 for more information. b See ISO 15156-2:2020, A.2.3.2.1 for more information. c Wireline lubricators and lubricator connecting devices are not excluded. d For sucker rod pumps and sucker rods, reference can be made to NACE MR0176.

Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons

EN ISO 15156-1:2020 石油和天然气工业.油,气生产中含硫化氢(H2S)环境下使用的材料.第1部分:耐裂化材料选择的一般原则

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2020)

EN ISO 15156-2:2020 石油,石化和天然气工业.油,气生产中含硫化氢(H2S)环境下使用的材料.第2部分:耐裂化碳和低合金钢及铸铁的使用

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons (ISO 15156-2:2020)

EN ISO 15156-3:2020 石油,石化和天然气工业.油,气生产中含硫化氢(H2S)环境下使用的材料.第3部分:耐裂化CRAs(耐腐蚀合金)和其他合金

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2020)

SY/T 7457-2019 石油、石化和天然气工业 油气生产系统的材料选择和腐蚀控制

Material selection and corrosion control for oil and gas production systems in the petroleum, petrochemical and natural gas industries

T/ZZB 0887-2018 天然气用流量控制铝制轨道球阀

本标准规定了天然气用流量控制铝制轨道球阀的术语和定义、结构型式、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本标准适用于公称压力PN16、公称尺寸DN50～DN200、工作温度-20 ℃～60 ℃，端部连接形式为法兰，用于天然气流量控制的铝制轨道球阀（以下简称“球阀”）。

Flow control aluminum-alloy orbit ball valves for natural gas

KS B ISO 16903-2017(2022) 石油和天然气工业.影响设计和材料选择的液化天然气特性

Petroleum and natural gas industries - Characteristics of LNG, influencing the design, and material selection

KS B ISO 16903-2017 石油和天然气工业 - Lng的特点 影响设计和材料选择

Petroleum and natural gas industries - Characteristics of LNG, influencing the design, and material selection

KS B ISO 16903:2017 石油和天然气工业 - Lng的特点 影响设计和材料选择

Petroleum and natural gas industries - Characteristics of LNG, influencing the design, and material selection

BS EN ISO 17781:2017 石油石化和天然气工业 铁素体/奥氏体（双相）不锈钢显微组织质量控制试验方法

Petroleum, petrochemical and natural gas industries. Test methods for quality control of microstructure of ferritic/austenitic (duplex) stainless steels

EN ISO 17781:2017 石油石化和天然气工业. 铁素体/奥氏体(双相)不锈钢显微组织质量控制试验方法

Petroleum@ petrochemical and natural gas industries - Test methods for quality control of microstructure of ferritic/austenitic (duplex) stainless steels

ISO 17781:2017 石油石化和天然气工业. 铁素体/奥氏体(双相)不锈钢显微组织质量控制试验方法

This document specifies quality control testing methods and test conditions for the characterization of microstructure in relation to relevant properties in ferritic/austenitic (duplex) stainless steel components supplied in the solution annealed condition and fabrication welds in the as welded condition. This document supplements the relevant product and fabrication standards with respect to destructive testing methods including sampling of test specimens, test conditions and test acceptance criteria to show freedom from deleterious intermetallic phases and precipitates in duplex stainless steels. In addition, this document specifies the documentation of testing and test results by the testing laboratory. NOTE 1 This document is based upon experience with duplex stainless steels in offshore oil and gas industry applications including topside and subsea hydrocarbon service, sea water service, as well as structural use. NOTE 2 The austenite spacing is relevant to the susceptibility of duplex stainless steels to hydrogen-induced stress cracking (HISC) in subsea applications where cathodic protection is applied. This falls outside the scope of this document. Reference is made to DNV/GL RP-F112[4].

Petroleum, petrochemical and natural gas industries - Test methods for quality control of microstructure of ferritic/austenitic (duplex) stainless steels

DIN EN ISO 14224:2017 石油、石化产品和天然气工业 设备可靠性和维修数据的采集与交换(ISO 14224-2016,修正版2016-10-01) 英文版本EN ISO 14224-2016

Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment (ISO 14224:2016, Corrected version 2016-10-01); English version EN ISO 14224:2016, only on CD-ROM

SY/T 6476-2017 管线钢管落锤撕裂试验方法

Drop weight tear test method for pipeline steel pipes

GSO ISO 23936-2:2016 石油、石化和天然气工业 与石油和天然气生产相关的介质接触的非金属材料 第2部分：弹性体

ISO 23936 describes general principles and gives requirements and recommendations for the selection and qualification of non-metallic materials for service in equipment used in oil and gas production environments, where the failure of such equipment could pose a risk to the health and safety of the public and personnel, or to the environment. It can be applied to help avoid failures of the equipment itself. It supplements, but does not replace, the material requirements given in the appropriate design codes, standards or regulations. This part of ISO 23936 describes the requirements and procedures for qualification of elastomeric material used in equipment for oil and gas production.

Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 2: Elastomers

EN ISO 17348:2016 石油和天然气工业.材料选择为外壳,油管和井下设备含量高CO2环境（ISO17348:2016）

Petroleum and natural gas industries - Materials selection for high content CO2 environment for casings, tubings and downhole equipment (ISO 17348:2016)

T/CGAS 001-2016 宽边管件连接涂覆燃气管道技术规程

本标准的主要内容包括:总则、规范性引用文件、术语和定义、涂覆管技术要求、宽边管件技术要求、惰性填料技术要求、标志、标记和包装、装运与储存、产品验收要求、安全、卫生和环境保护、施工安装要求等。本标准的附录A、附录B、附录C、附录D、附录E为规范性附录，附录F、附录G、附录H为资料性附录。

Technical Specification for Connecting Collar Fitting with Pre-Coated Gas Pipe

ISO 17348:2016 石油和天然气工业.套管,油管和井下设备较高二氧化碳含量的材料选择

This International Standard provides guidelines and requirements for material selection of both seamless casing and tubing, and downhole equipment for CO2 gas injection and gas production wells with high pressure and high CO2 content environments [higher than 10 % (molar) of CO2 and 1 MPa CO2 partial pressure]. Oil production wells are not covered in this International Standard. This International Standard only considers materials compatibility with the environment. Guidance is given for the following: — corrosion evaluation; — materials selection; — corrosion control. This International Standard is aimed at high CO2 content wells, where the threat of low pH and CO2 corrosion is greatest. However, many aspects are equally applicable to environments containing lower CO2 concentrations. Materials selection is influenced by many factors and synergies and should be performed by either materials or corrosion engineer.

Petroleum and natural gas industries - Materials selection for high content CO2 for casing, tubing and downhole equipment

KS B ISO 15156-1-2015(2020) 石油和天然气工业 - 材料在石油和天然气生产环境中含硫化氢使用 - 第1部分:总则开裂 耐磨材料的选择

Petroleum and natural gas industries－Materials for use in H2S-containing environments in oil and gas production－Part 1：General principles for selection of cracking-resistant materials