77.140.30 承压钢 标准查询与下载

DS/EN 10314:2003 高温下钢的保证强度最小值的推导方法

This standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures. However, this standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

DIN EN 10314:2003 高温下验证钢强度最小值导出法

The document specifies a method for deriving the minimum proof strengh values for steels at elevated temperatures. This standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures; German version EN 10314:2002

BS EN 10314:2002 高温下钢保证强度最小值的运算方法

This European Standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures. However, this standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

ASTM A1014-02 高温用沉淀硬化螺栓材料（UNS N07718）的标准规范

1.1 This specification covers a precipitation hardening bolting material (UNS N07718) for high temperature service.

Standard Specification for Precipitation-Hardening Bolting Material (UNS N07718) for High Temperature Service

ASTM A1014-00 高温用沉淀硬化螺栓材料（UNS N07718）的标准规范

1.1 This specification covers a precipitation hardening bolting material (UNS N07718) for high temperature service.

Standard Specification for Precipitation-Hardening Bolting Material (UNS N07718) for High Temperature Service

EN 10314:2002 高温下钢的校验强度最小值的推导方法;代替ENV 22605-1-1991,ENV 22605-2-1991和ENV 22605-3-1991

This European Standard specifies a method for derivingThe minimum proof strength valuesfor steels at elevated temperatures.However,This standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

CNS 11109-2001 焊接结构用高降伏强度钢板

本标准适用于压力容器、高压设备及其它结构物所使用之具有良好焊接性之钢板，抗拉强度为 780N∕mm2 ，降伏强度为 685N∕mm2 级之热轧钢板（以下简称钢板）。附录 3 及附录 4 对钢料之规定亦构成标准之一部分，但附录 2~4（分别对应于 ISO 4950-1~3）的内容自成为一完整之规

High yield strength steel plates for welded structure

ASTM A662/A662M-99 碳锰硅钢压力容器用中压和低温用标准规范

1.1 This specification covers three grades of carbon-manganese-silicon steel plates intended primarily for service in welded pressure vessels where improved low temperature notch toughness is important. 1.2 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification to 2 in. [50 mm]. 1.3 Grades A, B, and C comply substantially with the requirements of ISO Pressure Vessel Steels P9, P15, and P18, respectively. 1.4 For plates produced from coil, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A 20/A 20M apply.1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service

ASTM A612/A612M-01 压力容器板 碳钢 高强度 中温和低温服务的标准规范

1.1 This specification covers killed carbon-manganese-silicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures. 1.2 The maximum thickness of plates supplied under this specification is 1 in. [25 mm]. 1.3 For plates produced from coil, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

CNS 4273-2001 高压瓦斯容器用钢板、钢片及钢带

本标准适用于充填高压气体，如液化石油，乙炔及氟碳气体而内容积在 500L 以下之焊接容器用热轧钢板、钢片及钢带（以下简称为钢板、钢片及钢带）。备考：本标准采用国际单位制（SI），｛｝内之单位及数值仅供参考。

Steel plates,sheets and strips for gas cylinders

ASTM A240/A240M-99b 用于压力容器的铬和铬镍不锈钢板 板和带的标准规范和一般应用

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

JIS G 3116:2000 气瓶用薄钢板、钢板和钢带

Steel sheets, plates and strip for gas cylinders

JIS G 3115:2000 中等温度用压力容器的钢板

Steel plates for pressure vessels for intermediate temperature service

ASTM A736/A736M-88(2000) 低碳时效硬化镍铜铬钼铌和镍铜锰钼铌合金钢压力容器板的标准规范

Standard Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium and Nickel-Copper-Manganese-Molybdenum-Columbium Alloy Steel

ASTM A202/A202M-93(1999) 压力容器板合金钢铬锰硅标准规范

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon

ASTM A543/A543M-93(1999) 调质镍铬钼合金钢压力容器板标准规范

Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered Nickel-Chromium-Molybdenum

NF A36-220:1999 简单压力容器用钢.板材、带材和棒材的交货技术要求

Steels for simple pressure vessels. Technical delivery requirements for plates, strips and bars.

KS D 3853-1997 压力容器用钢板(第1部分:厚板材)

이 규격은 압력 용기 및 고압 설비 등(고온 및 저온에서 사용하는 것을 제외한다.)에 이용

Steel plates for pressure vessels for intermediate temperature service -Part 1 : Thicker plates

KS D 3853-1997(2022) 中温压力容器用钢板.第1部分:厚板

Steel plates for pressure vessels for intermediate temperature service -Part 1 : Thicker plates

KS D 3853-1997(2017) 钢板压力容器用中温SERVICE - 第1部分:厚板

Steel plates for pressure vessels for intermediate temperature service -Part 1 : Thicker plates