77.140.30 承压钢 标准查询与下载

DS-håndbog 111.3:2010 钢铁 第3部分：压力用钢

This handbook for iron and steel includes standards for steels for pressure purposes.

Iron and steel - Part 3: Steels for pressure purposes

ASTM A479/A479M-10a 锅炉和其他压力容器用不锈钢棒材和型材标准规范

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

ASTM A479/A479M-10 锅炉和其他压力容器用不锈钢棒材和型材标准规范

1.1 This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction. Note 18212;There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

ASTM A387/A387M-10 压力容器用铬钼合金钢板的标准规格

1.1 This specification covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. 1.2 Plates are available under this specification in several grades having different alloy contents as follows:

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum

ASTM A562/A562M-10(2015) 玻璃或扩散金属涂层用锰钛碳钢压力容器板的标准规格

1.1 This specification2 covers titanium-bearing carbon steel plates intended for welded glass lined pressure vessels or other applications where the presence of free-iron carbide would be deleterious to the coating. A minimum specific ratio of titanium to carbon is specified. 1.2 The maximum thickness of plates is limited to 2 in. [50 mm]. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings

ASTM A516/A516M-10(2015) 中温和低温服务用碳钢压力容器板的标准规格

1.1 This specification2 covers carbon steel plates intended primarily for service in welded pressure vessels where improved notch toughness is important. 1.2 Plates under this specification are available in four grades having different strength levels as follows: 8201;Grade U.S. [SI] Tensile Strength, ksi [MPa] 55 [380] 55–75 [380–515] 60 [415] 60–80 [415–550] 65 [450] 65–85 [450–585] 70 [485] 70–90 [485–620] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows: 8201;Grade U.S. [SI] Maximum Thickness, in. [mm] 55 [380] 12 [305] 60 [415]  8 [205] 65 [450]  8 [205] 70 [485]  8 [205]

Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service

ASTM A517/A517M-10(2015) 高强度淬火和回火用合金钢压力容器板的标准规格

1.1 This specification2 covers high-strength quenched and tempered alloy steel plates intended for use in fusion welded boilers and other pressure vessels. 1.2 This specification includes a number of grades as manufactured by different producers, but all having the same mechanical properties and general characteristics. 1.3 The maximum thickness of plates furnished under this specification shall be as follows: Grade Thickness A, B 1.25 in. [32 mm] H, S 2 in. [50 mm] P 4 in. [100 mm] F 2.50 in. [65 mm] E, Q 6 in. [150 mm] 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other without combining values in any way.

Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered

ASTM A723/A723M-10(2015) 高强度压力组件应用使用合金钢锻件的标准规格

1.1 This specification2 covers requirements for high-strength quenched and tempered alloy steel forgings for pressure vessels, isostatic presses, shock tubes, and similar components. 1.2 These materials are not intended for welded construction. 1.3 Three grades of nickel-chromium-molybdenum steels and six classes of increasing tensile strength are included. The strength class, section size, and configuration of the forging will largely dictate the applicable type(s) of steel. 1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application

ASTM A515/A515M-10 中温及高温压力容器用碳素钢板的标准规格

1.1 This specification covers carbon-silicon steel plates primarily for intermediate- and higher-temperature service in welded boilers and other pressure vessels.

Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service

ASTM A516/A516M-10 中温及低温压力容器用碳素钢板材的标准规格

1.1 This specification covers carbon steel plates intended primarily for service in welded pressure vessels where improved notch toughness is important. 1.2 Plates under this specification are available in four grades having different strength levels as follows:

Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service

ASTM A723/A723M-10 高强度压力件用合金钢锻件的标准规格

1.1 This specification covers requirements for high-strength quenched and tempered alloy steel forgings for pressure vessels, isostatic presses, shock tubes, and similar components. 1.2 These materials are not intended for welded construction. 1.3 Three grades of nickel-chromium-molybdenum steels and six classes of increasing tensile strength are included. The strength class, section size, and configuration of the forging will largely dictate the applicable type(s) of steel. 1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application

ASTM A240/A240M-10b 一般用途用压力容器用铬不锈钢和铬-镍不锈钢厚钢板,薄钢板和带材的标准规格

1.1 This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A1014/A1014M-10 高温设备用脱溶硬化螺栓组件(UNS N07718)标准规范

1.1 This specification covers precipitation hardening bolting (UNS N07718) for high temperature service. See Specification for the definition of “bolting.” 1.2 The following referenced general requirements are indispensable for application of this specification: Specification . 1.3 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4 This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service

ASTM A517/A517M-10 压力容器用经回火与淬火的高强度合金钢板

1.1 This specification covers high-strength quenched and tempered alloy steel plates intended for use in fusion welded boilers and other pressure vessels. 1.2 This specification includes a number of grades as manufactured by different producers, but all having the same mechanical properties and general characteristics.

Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered

ASTM A515/A515M-10(2015) 中温和高温服务用碳钢压力容器板的标准规格

1.1 This specification2 covers carbon-silicon steel plates primarily for intermediate- and higher-temperature service in welded boilers and other pressure vessels. 1.2 Plates under this specification are available in three grades having different strength levels as follows: Grade U.S. [SI] Tensile Strength, ksi [MPa] 60 [415] 60–80 [415–550] 65 [450] 65–85 [450–585] 70 [485] 70–90 [485–620] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows: Grade U.S. [SI] Maximum Thickness, in. [mm] 60 [415]  8 [200] 65 [450]  8 [200] 70 [485]  8 [200] 1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply. 1.5 The values stated in either inch-pound units or SI units are to be regard......

Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service

ASTM A562/A562M-10 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板标准规格

1.1 This specification covers titanium-bearing carbon steel plates intended for welded glass lined pressure vessels or other applications where the presence of free-iron carbide would be deleterious to the coating. A minimum specific ratio of titanium to carbon is specified. 1.2 The maximum thickness of plates is limited to 2 in. [50 mm]. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings

KS D 3543-2009 锅炉和其他压力容器用铬钼合金钢板

이 표준은 보일러 및 압력 용기(저온에서 사용하는 것을 제외한다.)에 사용하는 크로뮴 몰리

Chromium-molybdenum alloy steel plates for boilers and pressure vessels

NB/T 47002.1-2009 压力容器用爆炸焊接复合板.第1部分:不锈钢-钢复合板

NB/T 47002的本部分规定了以 不锈钢为覆材，碳素钢、低合金钢或不锈钢为基材，用爆炸焊接法制造的复合板的型式、尺寸、级别、技术要求、试验方法、检验规则、包装、标志和质量证明书等内容。 本部分适用于总厚度等于或大于8mm的压力容器用爆炸焊接不锈钢-钢复合板。

Explosion welded clad plate for pressure vessels.Part 1:Stainless steel-steel clad plate

EN 10028-4:2009 压力用平板钢制产品.第4部分:规定低温性质的镍合金钢

This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1. The requirements and definitions of EN 10028-1:2007 + A1:2009 also apply. NOTE OnceThis European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC; presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials inThis European Standard (Part 1 andThis Part 4 of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently; the assessment of the technical data stated inThis material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied; needs to be done.

Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties

ASTM A1014/A1014M-09 高温设备用沉淀硬化螺栓材料(UNS N07718)的标准规范

1.1 This specification covers precipitation hardening fasteners and fastener material (UNS N07718) for high temperature service. 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A 962/A 962M. 1.3 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4 This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Precipitation-Hardening Fasteners and Fastener Material (UNS N07718) for High Temperature Service