77.140.30 承压钢 标准查询与下载

ASTM A541/A541M-05(2015) 压力容器部件用淬火和回火碳素与合金钢锻件的标准规格

1.1 This specification2 covers requirements for quenched and tempered carbon and alloy steel forgings for pressure vessel components. 1.2 All grades are considered weldable under proper conditions. Welding technique is of fundamental importance, and it is presupposed that welding procedure and inspection will be in accordance with approved methods for the grade of material used. Note 1: Grades 1 and 1A have different chemistries but the same mechanical requirements. Note 2: Designations have been changed as follows: Current Formerly     Grade 1 Class 1 Grade 1A Class 1A Grade 1C Class 4 Grade 2 Class 1 Class 2 Grade 2 Class 2 Class 2A Grade 3 Class 1 Class 3 Grade 3 Class 2 Class 3A Grade 4N Class 1 Class 7 Grade 4N Class 2 Class 7A Grade 4N Class 3

Standard Specification for Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components

KS D ISO 6303-2004(2009) 压力容器钢不包括在ISO 2604中 第1部分长期应力破裂性能的6-推导

Pressure vessel steels not included in ISO 2604, Part 1 to 6 - Derivation of long time stress rupture properties

KS D ISO 9327-1-2004(2009) 用于压力目的的钢锻件和轧制或锻造钢筋 - 技术交付条件 - 第1部分:一般要求

Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions Part 1 General requirements

KS D ISO 2605-3-2004(2009) 用于压力用途的钢产品 - 高温特性的衍生和验证 - 第3部分:当数据有限公司获得高温温度或耐压应力的替代方法

Steel products for pressure purposes Derivation and verification of elevated temperature properties Part 3 An alternative procedure for deriving the elevated temperature yield or proof stress properti

KS D ISO 4978-2004(2009) 用于焊接气瓶的平轧钢产品

Flat rolled steel products for welded gas cylinders

ASTM A533/A533M-93(2004)e1 压力容器板 合金钢 淬火和淬火 锰 - 钼和锰 - 钼 - 镍的标准规范

Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel

ASTM A240/A240M-04a 用于压力容器的铬和铬镍不锈钢板 板和带的标准规范和一般应用

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM A859/A859M-04(2014) 压力容器部件用时效硬化合金钢锻件的标准规格

1.1 This specification covers requirements for low-carbon age-hardening nickel-copper-chromium-molybdenum-columbium alloy steel forgings for pressure vessel components. 1.2 Forgings under this specification are available as Grades A or B. Grade A may be ordered in one or two classes as follows: 1.2.1 Grade A Class 1—Normalized-and-precipitation-heat-treated, providing a minimum yield strength of 55 ksi [380 MPa] and a minimum tensile strength of 65 ksi [450 MPa]. 1.2.2 Grade A Class 2—Quenched-and-precipitation-heat-treated, providing a minimum yield strength of 65 ksi [450 MPa] and a minimum tensile strength of 75 ksi [MPa]. 1.2.3 Grade A was the original steel composition in this specification. 1.3 Although the material is readily weldable, welding procedures are of fundamental importance and must be such as not to affect adversely the properties of the material, especially in the heat-affected zone. It is presupposed that welding procedures will be suitable for the material being welded. 1.4 Supplementary requirements, including those applicable in Specification A788/A788M, are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units.

Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components

KS D 3575-2003 高压气体容器用无缝钢管

이 규격은 KS B 6217 및 KS B 6210의 제조에 사용하는 이음매 없는 강관(

Seamless steel tubes for high pressure gas cylinder

KS D ISO 9329-1-2003(2013) 承压用无缝钢管交货技术条件第1部分:规定室温性能的非合金钢

Seamless steel tubes for pressure purposes－Technical delivery conditions－ Part 1：Unalloyed steels with specified room temperature properties

KS D ISO 9329-2-2003(2013) 承压用无缝钢管交货技术条件第2部分:规定高温性能的非合金钢和合金钢

Seamless steel tubes for pressure purpose－Technical delivery Conditions－Part 2：Unalloyed and alloyed steels with specified elevated temperature properties

KS D ISO 9328-3-2003(2013) 承压用钢板和钢带交货技术条件第3部分:规定低温性能的镍合金钢

Steel plates and strips for pressure purposes－Technical delivery conditions－Part 3：Nickel-alloyed steels with specified low temperature properties

ASTM A612/A612M-03 压力容器板 碳钢 高强度 中温和低温服务的标准规范

1.1 This specification covers killed carbon-manganese-silicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures. 1.2 The maximum thickness of plates supplied under this specification is 1 in. [25 mm]. 1.3 For plates produced from coil, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

ASTM A735/A735M-03 中低温用压力容器用低碳锰钼铌合金钢板的标准规范

1.1 This specification covers low-carbon manganese-molybdenum-columbium alloy steel plates for piping components and welded pressure vessels. 1.2 Four different classes are covered, which provide various tensile strength properties. A Charpy V-notch energy absorption requirement of 20 ftl183;bf [27J] at -50176;F [-45176;C] is specified for all grades. 1.2.1 Classes 1 and 2 provide minimum yield strength levels of 65 ksi [450 MPa] and 70 ksi [485 MPa] respectively. Both classes can be provided in the as-rolled condition or in the quenched-and-tempered condition. 1.2.2 Class 3 provides a minimum yield strength level of 75 ksi [515 MPa]. This grade can be provided in the as-rolled and precipitation heat-treated condition or in the quenched-and-tempered condition. 1.2.3 Class 4 provides a yield strength level of 80 ksi [550 MPa] in the as-rolled and precipitation heat-treated condition. 1.3 Current practice limits plate thickness furnished under this specification. The individual manufacturer should be consulted on size and thickness limitations. 1.4 Welding procedures are of fundamental importance and must be such as not to adversely affect the properties of the material, especially in the heat-affected zone. It is presupposed that welding procedures will be suitable for the materials being welded. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Pressure Vessel Plates, Low-Carbon Manganese-Molybdenum-Columbium Alloy Steel, for Moderate and Lower Temperature Service

LST EN 10314-2003 高温下钢的保证强度最小值的推导方法

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

NF A03-035:2003 高温下钢保证强度最小值的导出法

Method for the derivation of minimum values of proof strength of steel at elevated temperatures.

ASTM A508/A508M-03 用于压力容器的淬火和回火真空处理的碳钢和合金钢锻件的标准规范

1.1 This specification covers quenched and tempered vacuum treated carbon and alloy steel forgings for pressure vessels such as those used in reactor systems. Specifically, it covers forgings for vessel closures, shells, flanges, tube sheets, rings, heads, and similar parts.1.2 All grades are considered weldable under proper conditions. Welding technique is of fundamental importance, and it is presupposed that welding procedure and inspection will be in accordance with approved methods for the grade of material used.1.3 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text and the tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.1.4 Unless the order specifies the applicable "M" specification designation, the material shall be furnished to the inch-pound units.Note 18212;Grades 1 and 1A are composed of different chemistries but have the same mechanical requirements.Note 28212;Designations have been changed as follows:CurrentFormerlyGrade 1Class 1Grade 1AClass 1AGrade 2 Class 1Class 2Grade 2 Class 2Class 2AGrade 3 Class 1Class 3Grade 3 Class 2Class 3AGrade 4N Class 1Class 4Grade 4N Class 2Class 4AGrade 4N Class 3Class 4BGrade 5 Class 1Class 5Grade 5 Class 2Class 5AGrade 22 Class 3Class 22BGrade 3VClass 3VGrade 6 Classes 1, 2, 3, and 4N/A

Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels

DS/EN 10314:2003 高温下钢的保证强度最小值的推导方法

This standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures. However, this standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

DIN EN 10314:2003 高温下验证钢强度最小值导出法

The document specifies a method for deriving the minimum proof strengh values for steels at elevated temperatures. This standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures; German version EN 10314:2002

BS EN 10314:2002 高温下钢保证强度最小值的运算方法

This European Standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures. However, this standard does not specify a verification procedure.

Method for the derivation of minimum values of proof strength of steel at elevated temperatures