共找到 331 条与 承压钢 相关的标准,共 23 页
1.1 This specification covers 98201;% nickel-alloy steel plates produced by the direct-quenching process. The plates are intended primarily for use in welded pressure vessels. 1.2 The direct-quenching process consists of quenching the plates directly after rolling, without permitting the plates to cool below the critical temperature prior to initiation of the quenching operation, and subsequently tempering the plates. (This differs from the “conventional” process in which the plates are permitted to cool to a temperature significantly below the critical temperature, usually to ambient temperature, prior to reheating to a temperature above the upper critical temperature, then quenching, and subsequently tempering.) 1.3 The maximum nominal thickness of plates furnished under this specification shall not exceed 2 in. [50 mm]. 1.4 This material is susceptible to magnetization. Use of magnets in handling after heat treatment should be avoided if residual magnetism would be detrimental to subsequent fabrication or service. 1.5 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
Standard Specification for Steel Plates, 9&x2009;%&x2009; Nickel Alloy, for Pressure Vessels, Produced by the Direct-Quenching Process
이 표준은 압력 용기 및 고압 설비 등(고온 및 저온에서 사용하는 것을 제외한다.)에 사용
Steel plates for pressure vessels for intermediate temperature service
This European Standard specifies requirements for hot-rolled sheet and strip up to 5 mm thickness of steels listed in Table 1 and intended for manufacturing welded gas cylinders.The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard.NOTE Sheet and strip made of: - general structural steels (see EN 10025 series);- non-alloy and alloy steels for pressure equipment (see EN 10028-1 to EN 10028-6);- low carbon non-alloy steels for cold forming (see EN 10111 and EN 10130);- steels with high yield strength for cold forming (see EN 10149);- cold rolled strip up to 600 mm wide of low carbon non
Steel sheet and strip for welded gas cylinders
이 표준은 LP 가스, 아세틸렌, 각종 프레온 가스 등의 고압 가스를 충전시키는 내용적 5
Steel sheets, plates and strip for gas cylinders
이 표준은 저온에서 사용하는 압력 용기 및 설비에 사용하는 열간 압연 탄소강 강판(이하 강
Carbon steel plates for pressure vessels for low temperature service
This European Standard applies to steel castings for pressure containing parts. It includes materials which are used for the manufacture of components, for pressure equipment.This European Standard relates to castings characterised by their chemical composition (see Table 2) and mechanical properties (see Tables 3 to 6).In cases where castings are joined by welding by the founder, this European Standard applies.In cases where castings are welded:- to wrought products (plates, tubes, forgings), or- by non founders,this European Standard does not apply.NOTE For this harmonised supporting standard for materials, presumption of conformity to the Essential Requi
Steel castings for pressure purposes
Steel castings for pressure purposes; German version EN 10213:2007, Corrigendum to DIN EN 10213:2008-01; German version EN 10213:2007/AC:2008
Steel castings for pressure purposes
Steel castings for pressure purposes
This European Standard applies to steel castings for pressure containing parts. It includes materials which are used for the manufacture of components, for pressure equipment.This European Standard relates to castings characterised by their chemical composition (see Table 2) and mechanical properties (see Tables 3 to 6).In cases where castings are joined by welding by the founder, this European Standard applies.In cases where castings are welded:- to wrought products (plates, tubes, forgings), or- by non founders,this European Standard does not apply.NOTE For this harmonised supporting standard for materials, presumption of conformity to the Essential Requi
Steel castings for pressure purposes
This European Standard applies to steel castings for pressure containing parts. It includes materials which are used for the manufacture of components, for pressure equipment. This European Standard relates to castings characterised by their chemical composibon (see Table 2) and mechanical properties (see Tables 3 to 6). In cases where castings are joined by welding by the founder, this European Standard applies. In cases where castings are welded: -- to wrought products (plates, tubes, forgings), or -- by non founders, this European Standard does not apply. NOTE For this harmonised supporting standard for materials, presumption of conformity to the Essential Requirements of the Directive is limited to technical data of the material in the standard and does not presume adequacy of the material to specific equipment. Consequently the technical data stated in the material standard should be assessed against the design requirements of the specific equipment to verify that the Essential Requirements of the Pressure Equipment Directive (PED) are satisfied.
Steel castings for pressure purposes; English version of DIN EN 10213:2008-01
Steel castings for pressure purposes.
This European Standard applies to steel castings for pressure containing parts. It includes materials which are used for the manufacture of components, for pressure equipment. This European Standard relates to castings characterised by their chemical composition (see Table 2) and mechanical properties (see Tables 3 to 6). In cases where castings are joined by welding by the founder, this European Standard applies. In cases where castings are welded: to wrought products (plates, tubes, forgings), or by non founders, this European Standard does not apply. NOTE For this harmonised supporting standard for materials, presumption of conformity to the Essential Requirements of the Directive is limited to technical data of the material in the standard and does not presume adequacy of the material to specific equipment. Consequently the technical data stated in the material standard should be assessed against the design requirements of the specific equipment to verify that the Essential Requirements of the Pressure Equipment Directive (PED) are satisfied.
Steel castings for pressure purposes
Nickel steel plates for pressure vessels for low temperature service
Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates quenched and tempered for pressure vessels
Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates for boilers and other pressure vessels
Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates for boilers and other pressure vessels
Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates quenched and tempered for pressure vessels
이 규격은 저온에서 사용하는 압력 용기 및 설비에 사용하는 열간 압연 니켈 강판(이하, 강
Nickel steel plates for pressure vessels for low temperature service
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号