81.040.01 玻璃综合 标准查询与下载

KS L ISO 7884-6-2019 玻璃 粘度和粘度测定固定点 第6部分：软化点的测定

Glass — Viscosity and viscometric fixed points — Part 6: Determination of softening point

KS L ISO 7884-7-2019 玻璃 粘度和粘度测定固定点 第7部分：通过梁弯曲确定退火点和应变点

Glass — Viscosity and viscometric fixed points — Part 7: Determination of annealing point and strain point by beam bending

KS L 2401-2019 玻璃退火点和应变点弯曲测试方法

Testing method for annealing point and strain point of glass by beam bending

KS L 2106-2019 激光干涉法测量玻璃均匀性的方法

Measuring method for the homogeneity of glasses by laser interferometry

KS L 2506-2019 玻璃平均线性热膨胀测试方法

Testing method for average linear thermal expansion of glass

ASTM E1967-19 用油浸法和相衬显微镜自动测定玻璃样品折射率的标准试验方法

1.1 This test method covers a procedure for measuring and comparing the refractive index (η) at a fixed wavelength (λ) and temperature (T) (ηλ T ) of glass from known sources to recovered fragments from a questioned source. 1.2 This test method does not include the measurement of optical dispersion or the measurement of refractive index (ηλ T ) at any other wavelength other than the Sodium D line (ηD T ). This method employs a narrow band pass filter at 589 nm, but other filters could be employed using the described method, allowing the ηλ T to be determined at other wavelengths, and therefore, also allowing for the dispersion value to be calculated. 1.3 Alternative methods for the determination of ηλ T are listed in Refs (1-5).2 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard cannot replace knowledge, skills, or abilities acquired through education, training, and experience and is to be used in conjunction with professional judgment by individuals with such discipline-specific knowledge, skills, and abilities. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for the Automated Determination of Refractive Index of Glass Samples Using the Oil Immersion Method and a Phase Contrast Microscope

T/WZOHOA 01-2019 “瓯海眼镜”浙江区域名牌标识获准使用条件

标准规定了基本条件、管理体系、资源条件、产品标准、产品质量控制、企业品牌宣传、售后服务建设、企业发展计划。

"Ouhai Glasses" Zhejiang Regional Famous Brand Logo Approved Conditions for Use

T/ZZB 1166-2019 单片防火玻璃

本标准规定了单片防火玻璃的术语和定义、耐火等级及标记、基本要求、技术要求、试验方法、检验规则、标志、产品使用说明书、包装、运输、贮存、安装及质量与服务承诺。 本标准适用于采用物理钢化和（或）化学钢化相结合的综合增强技术工艺制造的单片钠钙硅防火玻璃。

Monolithic fire-resistant glass

ASTM C1350M-96(2019) 在软化点和退火范围之间测量玻璃粘度的标准试验方法（约10⁸Pa·；s到大约10^{13Pa和xb7；s） 通过梁弯曲（公制）}

1.1 This test method covers the determination of glass viscosity from approximately 108 Pa·s to approximately 1013 Pa·s by measuring the rate of viscous bending of a simply loaded glass beam.2 Due to the thermal history of the glass, the viscosity may not represent conditions of thermal equilibrium at the high end of the measured viscosity range. Measurements carried out over extended periods of time at any temperature or thermal preconditioning will minimize these effects by allowing the glass to approach equilibrium structural conditions. Conversely, the method also may be used in experimental programs that focus on nonequilibrium conditions. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Viscosity of Glass Between Softening Point and Annealing Range (Approximately 10⁸ Pa·s to Approximately 10¹³ Pa·s) by Beam Bendi

T/ZBH 013-2019 夹层玻璃用乙烯-乙酸乙烯酯共聚物（EVA）中间膜

本标准规定了夹层玻璃用乙烯-乙酸乙烯酯共聚物（EVA)中间膜的术语和定义、分类、要求、试验方法、检验规则、包装、标志、运输和贮存要求。 本标准适用于建筑夹层玻璃、室内装饰及家居夹层玻璃、淋浴房夹层玻璃、光伏组件封装用无色透明EVA中间膜，其它夹层玻璃用彩色EVA中间膜可参照本标准使用。

Ethylene-vinyl acetate co-polymer (EVA) interlayer for laminated glass

ASTM E2188-19 中空玻璃组件性能的标准试验方法

1.1 This test method covers procedures for testing the performance of preassembled permanently sealed insulating glass units or insulating glass units with capillary tubes intentionally left open. 1.2 This test method is applicable only to insulating glass units that are constructed with glass. 1.3 This test method is applicable to both double-glazed and triple-glazed insulating glass units. For triple-glazed insulating glass units where both of the outer lites are glass and the inner lite is either glass or a suspended film. 1.4 The unit construction used in this test method contains dimensions that are an essential component of the test. Different types of glass, different glass thicknesses, and different cavity sizes may affect the test results. 1.5 This test method is not applicable to insulating glass units containing a spandrel glass coating due to testing limitations. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Insulating Glass Unit Performance

DB41/T 1780-2019 中空玻璃门通用技术条件

General technical requirements for insulating glass doors

T/ZZB 0900-2018 液晶调光玻璃

本标准规定了液晶调光玻璃的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和安装以及质量与服务承诺。 本标准适用于中间层使用塑胶型液晶调光膜的干法夹层工艺生产的调光玻璃。

Liquid crystal switchable glass

T/SAS 0001-2018 淋浴房用安全玻璃 第1部分：钢化夹层玻璃

本部分规定了钢化夹层玻璃的术语和定义、材料、要求、试验方法、检验规则及包装、标识、运输和贮存。

Safety glass for shower enclosures - Part 1: Tempered laminated glass

T/SAS 0002-2018 淋浴房用安全玻璃 第2部分：贴膜钢化玻璃

本部分规定了贴膜钢化玻璃的术语和定义、材料、要求、试验方法、检验规则及包装、标识、运输和贮存。

Safety glass for shower enclosures Part 2: Toughened glass with film

DB42/T 1471-2018 玻璃容器包装、仓储、运输规范

Specifications for packaging, storage and transportation of glass containers

DB37/T 3353-2018 玻璃包装容器制造行业企业生产安全事故隐患排查治理体系实施指南

Implementation guide for the investigation and management system of hidden dangers of production safety accidents in the glass packaging container manufacturing industry

DB37/T 3293-2018 玻璃包装容器制造行业企业安全生产风险分级管控体系实施指南

Guidelines for the implementation of safety production risk classification management and control system for enterprises in the glass packaging container manufacturing industry

ASTM C1351M-96(2017) 测量10⁴Pa和xb7之间玻璃粘度的标准试验方法；s和10^{8Pa和xb7；固体右圆柱体粘性压缩产生的s【公制】}

Standard Test Method for Measurement of Viscosity of Glass Between 10⁴ Pa·s and 10⁸ Pa·s by Viscous Compression of a Solid Right Cylinder [Metric]

JC/T 2423-2017 玻璃熔窑余热发电设计规范

Design specifications for waste heat power generation in glass melting furnaces