81.040.20 建筑玻璃 标准查询与下载

23/30464856 DC BS EN 17940 建筑中的玻璃 用于制造夹层玻璃的 Folio 中间膜 产品标准

BS EN 17940. Glass in Building. Folio Interlayers for the Manufacturing of Laminated Glass. Product standard

BS EN 17635:2022 建筑中的玻璃 粉碎属性 要求及考核方法

1   Scope This document gives test methods to assess the shatter properties of different types of monolithic flat glass for use in building and construction works, for which a specific fragmentation pattern is required when tested under defined conditions. NOTE Thermally treated monolithic glass is a product for which such a requirement exists.

Glass in building. Shatter properties. Requirements and assessment methods

ASTM E2461-22 机场交通管制塔轿厢玻璃厚度测定的标准实施规程

1.1 This practice covers the determination of the thickness of glass installed in airport traffic control towers (ATCT) to resist a specified design loading with a selected probability of breakage less than or equal to either 1 lite per 1000 or 4 lites per 1000 at the first occurrence of the design wind loading. 1.2 The procedures apply to common outward sloping cab glass designs for which the specified loads do not exceed 15 kPa (313 psf). 1.3 The procedures assume control tower cab glass has an aspect ratio no greater than 3. 1.4 The procedures assume control tower cab glass has an area no less than 1.86 m2 (20 ft2 ). 1.5 The use of the procedures assumes the following: 1.5.1 Monolithic and laminated glass installed in ATCTs shall have continuous lateral support along two parallel edges, along any three edges, or along all four edges; 1.5.2 Insulating glass shall have continuous lateral support along all four edges; and 1.5.3 Supported glass edges are simply supported and free to slip in plane. 1.6 The procedures do not apply to any form of wired, patterned, etched, sandblasted, or glass types with surface treatments that reduce the glass strength. 1.7 The procedures do not apply to drilled, notched, or grooved glass. 1.8 The procedures address the determination of thickness and construction type to resist a specified design wind load at a selected probability of breakage. The final glass thickness and construction determined also depends upon a variety of other factors (see 5.4). 1.9 These procedures do not address blast loading on glass. 1.10 These procedures do not apply to triple-glazed insulating glass units. 1.11 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.12 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.13 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining the Thickness of Glass in Airport Traffic Control Tower Cabs

22/30454072 DC BS EN 17871 建筑中的玻璃 玻璃产品的分光光度特性 计算工具的验证程序

BS EN 17871. Glass in building. Spectrophotometric characteristics of glass products. Validation procedure for calculation tool

T/CASME 84-2022 建筑材料真空夹层隔热玻璃生产技术条件

本文件规定了尾矿废石建筑垃圾回收利用生产的术语和定义、一般规定、开采和加工、质量控制、 储存、综合利用和环境保护。

Technical conditions for the production of vacuum laminated insulating glass for building materials

GSO ISO 19916-1:2022 建筑用玻璃 真空中空玻璃 第1部分：产品基本规范及隔热、隔音性能评价方法

This document specifies product specification for vacuum insulating glass. It also specifies evaluation methods for thermal and sound insulating performance and evaluation methods for thermal insulation durability.

Glass in building — Vacuum insulating glass — Part 1: Basic specification of products and evaluation methods for thermal and sound insulating performance

GSO EN 1036-2:2022 建筑玻璃 内部使用的镀银浮法玻璃镜子 第2部分：合格评定；产品标准

This European Standard specifies requirements, the evaluation of conformity and the factory production control of flat mirrors from silver-coated float glass for internal use in buildings. NOTE For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.

Glass in building - Mirrors from silver-coated float glass for internal use - Part 2: Evaluation of conformity; product standard

JC/T 2658-2022 曲面玻璃三维形状偏差测试方法 激光扫描法

本文件规定了采用激光扫描测量曲面玻璃三维形状偏差的方法，包括术语和定义、原理、试验条件、试验仪器、试验步骤及试验报告等。 本文件适用于曲面玻璃三维形状偏差的测试。

Laser scanning method for measuring three-dimensional shape deviation of curved glass

JC/T 2669-2022 气凝胶中空玻璃

本文件规定了气凝胶中空玻璃的分类、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本文件适用于建筑及保温隔热用气凝胶中空玻璃。

Airgel hollow glass

JC/T 2670-2022 温致变色调光夹层玻璃

本文件规定了温致变色调光夹层玻璃的分类、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本文件适用于使用特殊中间层导致透射状态发生变化的建筑用温致变色调光夹层玻璃，其他领域使用的温致变色调光夹层玻璃可参照使用。

Thermochromic dimming laminated glass

JC/T 648-2022 平板玻璃配合料

本文件规定了平板玻璃配合料的术语和定义、技术要求、检验方法和检验规则。 本文件适用于平板玻璃配合料的质量检验，其它玻璃配合料的质量检验可参照使用。

flat glass batch

JC/T 2701-2022 建筑用减反射镀膜玻璃

本文件规定了建筑用减反射镀膜玻璃的术语和定义、分类、要求、试验方法、检验规则及包装、标志、运输和贮存。 本文件适用于幕墙、门窗及橱窗用减反射镀膜玻璃，室内装饰用减反射镀膜玻璃可参照使用。

Anti-reflection coated glass for building

T/CASME 30-2022 建筑用光致变色玻璃

本文件规定了建筑用光致变色玻璃的术语定义、分类、基本要求、试验方法、检验规则、标志、包装、运输与贮存技术要求。

Photochromic glass for building

T/FJAS 013-2022 LED 光电建筑玻璃

本文件规定了 LED 光电建筑玻璃的材料、要求、试验方法、检验规则、包装、标志、运输和贮存。 本文件适用于 LED 光电建筑玻璃。

LED Photovoltaic Architectural Glass

ASTM C1265-22 结构玻璃应用用中空玻璃边缘密封件拉伸性能测定的标准试验方法

1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion properties of insulating glass edge seals that are used in structural sealant glazing applications. Edge seals for these applications use a structural sealant to bond both glass lites and the edge spacer into a monolithic sealed insulating glass unit. In typical applications, the structural sealant acts to hold the outside lite in place under wind and gravity load and to maintain the edge spacer in its proper position. Hereafter, the term “insulating glass” will be abbreviated as “IG.” 1.2 The characterization of the IG secondary sealant properties, as defined by this test method, are strongly dependent on glass and edge spacer cleaning procedures, IG spacer profile, location of spacer, and primary IG sealant application. Users of this test method must recognize that the IG edge seal assembly influences the secondary sealant properties. 1.3 The values determined by this test method will be characteristic of the particular edge seal assembly that is tested. NOTE 1—Presently, only elastomeric, chemically curing silicone sealants specifically formulated for use as the secondary seal of IG units are recognized as having the necessary durability for use in structural sealant glazing applications. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications

BS ISO 21690:2021 建筑中的玻璃 玻璃块 规格及测试方法

What is ISO 21690 - Specifications and test methods for glass blocks about? ISO 21690 is one of a series of standards regarding glass in buildings. ISO 21690 specifies requirements for the properties of glass blocks used for the construction of non-load-bearing walls and horizontally spanning panels. ISO 21690 also specifies test methods used to verify these properties for square, rectangular and circular glass blocks. Who is ISO 21690 - Specifications and test methods for glass blocks for ? ISO 21690 on the specifications and test methods for glass blocks is useful for: Architects Manufacturers of glass blocks used in buildings Real estate developers Quality control personnel Testing and inspection personnel Why should you use ISO 21690 -

Glass in building. Glass blocks. Specification and test methods

BS ISO 18543:2021 建筑中的玻璃 电致变色釉 加速老化试验及要求

What is ISO 18543 - Electrochromic glazings about?    ISO 18543 specifies the accelerated ageing test and requirements for electrochromic glazings intended to either control direct or indirect solar transmission, or both. The electrochromic glazings can be assembled as insulating glass units, laminated glass, or a combination of both.   The test method described in ISO 18543 is only applicable to chromogenic glazings that can be switched between different transmission states using an electrical stimulus. This test method is applicable to any electrochromic glazing fabricated for use in buildings such as indoors, windows, skylights, exterior wall systems and glazing exposed to solar radiation.   Who is ISO 18543- Electrochromic glazings for?   ISO 18543 on the accelerated ageing test and requirements for electrochromic glazings is useful for:

Glass in building. Electrochromic glazings. Accelerated ageing test and requirements

JIS R 3111-3:2022 建筑玻璃 玻璃抗弯强度的测定 第3部分：试样两点支撑试验（四点弯曲）

Glass in building -- Determination of the bending strength of glass -- Part 3: Test with specimen supported at two points (four-point bending)

JIS R 3221:2022 光学镀膜玻璃

Optical coated glass

ISO/TS 21486:2022 建筑玻璃.建筑用夹层太阳能光伏玻璃的重新试验要求

Glass in building — Retesting requirements for laminated solar photovoltaic glass for use in buildings