81.040.20 建筑玻璃 标准查询与下载

ISO 12543-4:2021 建筑玻璃夹层玻璃和夹层安全玻璃第4部分:耐久性试验方法

This document specifies test methods relating to resistance to high temperature, humidity and radiation for laminated glass and laminated safety glass for use in building.

Glass in building — Laminated glass and laminated safety glass — Part 4: Test methods for durability

ISO 12543-5:2021 建筑玻璃夹层玻璃和夹层安全玻璃第5部分:尺寸和边缘处理

This document specifies dimensions, limit deviations and edge finishes of laminated glass and laminated safety glass for use in building. This document is not applicable to panes having an area less than 0,05 m2.

Glass in building — Laminated glass and laminated safety glass — Part 5: Dimensions and edge finishing

ISO 12543-3:2021 建筑玻璃夹层玻璃和夹层安全玻璃第3部分:夹层玻璃

This document specifies performance requirements for laminated glass as defined in ISO 12543-1. NOTE Any defects that are found in installed laminated safety glass are dealt with in ISO 12543-6.

Glass in building — Laminated glass and laminated safety glass — Part 3: Laminated glass

DIN EN 16759:2021 门窗和幕墙的粘合玻璃 铝和钢表面粘合机械性能的验证；德文版 EN 16759:2021

This document specifies the method to be used to verify the mechanical performance of the bonded glazing for doors, windows and curtain walling and its durability. The bonding covered is only that between the glass and the untreated, treated or coated metal surface. This document

Bonded Glazing for doors, windows and curtain walling - Verification of mechanical performance of bonding on aluminium and steel surfaces; German version EN 16759:2021

ISO 21690:2021 建筑玻璃.玻璃块.规范和试验方法

This document specifies requirements for the properties of glass blocks used for the construction of non-load-bearing walls and horizontally spanning panels. This document also specifies test methods used to verify these properties for square, rectangular and circular glass blocks.

Glass in building — Glass blocks — Specification and test methods

ASTM E2141-21 密封绝缘玻璃装置中电致变色器件加速老化的标准试验方法

1.1 This test method covers the accelerated aging of electrochromic devices (ECD) integrated in insulating glass units. 1.2 The test method is applicable for any electrochromic device incorporated into sealed insulating glass units (IGUs) fabricated for vision glass (superstrate and substrate) areas for use in buildings, such as sliding doors, windows, skylights, and exterior wall systems. The layers used for constructing the EC device and electrochromically changing the optical properties may be inorganic or organic materials. 1.3 The electrochromic (EC) glazings used in this test method are exposed to environmental conditions, including solar radiation. They are employed to control the amount of transmitted radiation by absorption and reflection and, thus, limit the solar heat gain and amount of solar radiation that is transmitted into the building. 1.4 The test method is not applicable to other chromogenic devices, such as, photochromic and thermochromic devices which do not respond to electrical stimulus. 1.5 The test method is not applicable to electrochromic (EC) glazings that are constructed from superstrate or substrate materials other than glass. 1.6 The test method referenced herein is a laboratory test conducted under specified conditions. The test is intended to simulate and, in some cases, to also accelerate actual in-service use of the electrochromic glazing. Results from these tests cannot be used to predict the performance with time of in-service units unless actual corresponding in-service tests have been conducted and appropriate analyses have been conducted to show how performance can be predicted from the accelerated aging tests. 1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Accelerated Aging of Electrochromic Devices in Sealed Insulating Glass Units

ASTM F1233-21 安全玻璃材料和系统的标准试验方法

1.1 This test method sets forth procedures whose purpose is limited to the evaluation of the resistance of security glazing materials and systems against the following threats: 1.1.1 Ballistic Impact, 1.1.2 Blunt Tool Impacts, 1.1.3 Sharp Tool Impacts, 1.1.4 Thermal Stress, and 1.1.5 Chemical Deterioration. NOTE 1—Specifically exempted from this test method are the use of power (motor or engine-driven) tools or devices, explosives, military ordinance (excepting small arms) and tools, processes or devices requiring more than two persons to transport and operate. 1.2 The values stated in inch-pounds are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see Warning in 10.1.1.6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Security Glazing Materials And Systems

ASTM F3057-21 嵌装玻璃电磁屏蔽效能的标准试验方法

1.1 This test method covers the determination of the electromagnetic shielding effectiveness of glazings or glazing configurations. 1.1.1 The intended application of this test method is for glazings or glazing configurations to be evaluated for their transmittance or shielding capability to electromagnetic frequencies. 1.1.2 This is a component test. It is not applicable to full systems such as walls, floors, ceilings, shielded racks, or window systems. 1.1.3 The intention of this test method is to standardize a measurement procedure for glazings or glazing configurations, with and without coatings, films, interlayers, or other enhancements, as single or insulating units at a standard size and when mounted in a standardized frame. 1.1.4 This test method is to provide a means of generating data for the glazing or glazing configuration infills that can be used by the consumer, designer, and system manufacturer to understand the capability and contribution of glazings or glazing configurations to a system used for Electromagnetic Interference (EMI) security. 1.2 This test method is for use in the assessment of EMI transmittance for frequency ranges 100 kHz to 20 GHz. Specific test frequencies within these ranges are required. 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 8 on Hazards. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Electromagnetic Shielding Effectiveness of Glazings

ASTM E2751/E2751M-21 支撑夹层玻璃走道的设计和性能的标准实施规程

1.1 This practice addresses elements related to load-bearing glass walkways, glass treads, and glass landings constructed with laminated glass. This standard includes performance, design, and safe behavior considerations. It addresses the characteristics unique to glass and laminated glass. Issues that are common to all walkways, such as slip resistance, are addressed in existing referenced standards. 1.2 This practice does not address glass walkways constructed with monolithic glass, glass block, insulating glass units, glass tiles that are directly bonded to a non-glass structural substrate, or glass walkways intended to support vehicular traffic. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Design and Performance of Supported Laminated Glass Walkways

ISO 18543:2021 建筑玻璃. 电致变色玻璃. 加速老化试验和要求

This document specifies the accelerated ageing test and requirements for electrochromic glazings intended to either control direct or indirect solar transmission, or both. The electrochromic glazings can be assembled as insulating glass unit, laminated glass or combination of both. The test method described in this document is only applicable to chromogenic glazings that can be switched between different transmission states using an electrical stimulus. This test method is not applicable to other chromogenic glazings such as photochromic and thermochromic glazings, which do not respond to electrical stimulus. This test method is applicable to any electrochromic glazing fabricated for use in buildings such as in doors, windows, skylights, exterior wall systems and glazing exposed to solar radiation. The materials used for constructing the electrochromic glazing and for electrochromically changing its optical properties can be inorganic or organic materials.

Glass in building - Electrochromic glazings - Accelerated ageing test and requirements

ISO 19916-3:2021 建筑玻璃.真空中空玻璃.第3部分：温差下性能评估的试验方法

This document specifies test methods for evaluation of performance of vacuum insulating glass samples with rigid edge seal when subjected to temperature differences between the glass sheets. This document is not applicable to vacuum insulating glass samples with flexible edge seal.

Glass in building - Vacuum insulating glass - Part 3: Test methods for evaluation of performance under temperature differences

UNI EN 16759-2021 门窗和幕墙用粘合玻璃 铝和钢表面粘合的机械性能验证

Bonded Glazing for doors, windows and curtain walling - Verification of mechanical performance of bonding on aluminium and steel surfaces

BS PD ISO/TS 21480:2021 建筑中的玻璃 建筑一体化光伏组件回收利用通用技术要求

Glass in building. General technical requirements of building integrated photovoltaic modules recycling

DS/EN 16759:2021 门、窗、幕墙粘结玻璃 铝钢表面粘结力学性能验证

Bonded Glazing for doors, windows and curtain walling – Verification of mechanical performance of bonding on aluminium and steel surfaces

BS EN 16759:2021 用于门、窗和幕墙的粘结玻璃 铝和钢表面粘合的机械性能验证

Bonded Glazing for doors, windows and curtain walling. Verification of mechanical performance of bonding on aluminium and steel surfaces

ASTM C1376-21a 平板玻璃上热解和真空沉积涂层的标准规范

1.1 This specification covers the optical and aesthetic quality requirements for pyrolytic and vacuum deposition coatings applied on flat glass for use in building glazing. 1.2 The coatings are applied on the glass using either pyrolytic or vacuum sputtering deposition methods to control solar heat gain, energy performance, comfort level, and condensation and to enhance the aesthetic of the building. 1.3 This specification addresses blemishes related to the coating only. It does not address glass blemishes, applied ceramic frits to spandrel glass, and organic film opacifiers. 1.4 The Nonuniformity for Coated Glass requirements, given in 6.10, pertain to glazing units of vertical and sloped orientations as installed in the building exterior. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass

ASTM C1652/C1652M-21 用网格数字摄影测量平板玻璃产品光学畸变的标准试验方法

1.1 This test method covers the determination of optical distortion of heat-strengthened and fully tempered architectural glass substrates which have been processed in a heat controlled continuous or oscillating conveyance oven. See Specifications C1036 and C1048 for discussion of the characteristics of glass so processed. In this test method the reflected image of processed glass is photographed and the photographic image analyzed to quantify the distortion due to surface waviness. The test method is also useful to quantify optical distortion observed in transmitted light in laminated glass assemblies. 1.2 The values stated in either SI units or inch-pound units are regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 There is no known ISO equivalent to this test method. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Optical Distortion in Flat Glass Products Using Digital Photography of Grids

JS 10047-5-2021 建筑物中的玻璃 绝缘玻璃单元第5部分：产品标准

Glass in buildings - Insulating glass units Part 5: Product standard

JS 10042-4-2021 建筑玻璃 镀膜玻璃 第4部分：产品标准

Glass in buildings - Coated glass Part 4: Product standard

ASTM C1464-21 弯曲玻璃的标准规范

1.1 This specification covers the requirements for bent glass used in general building construction, furniture, display, and various other non-automotive applications. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Bent Glass