91.060.10 墙、隔墙、面墙 标准查询与下载

KS F 4725-2023 木质墙板组件

Wood-based panel assembly for wall

T/SDAS 700-2023 OKS保温板外墙保温系统应用技术规程

1.0.1 为规范OKS保温板外墙保温系统的应用，做到安全适用、技术先进、经济合理，保证工程质量，制定本规程。 1.0.2 本规程适用于抗震设防烈度8度及以下地区新建、改扩建的民用与工业建筑的外墙保温工程。 1.0.3 OKS保温板外墙保温系统的设计、施工及验收，除应符合本规程的规定外，尚应符合国家、行业和山东省现行有关标准的规定。

Technical specification for application of OKS insulation board external wall insulation system

DB36/T 1808-2023 中小学校教室LED照明技术规范

Technical Specifications for LED Lighting in Primary and Secondary School Classrooms

T/ZS 0504-2023 气凝胶保温膏料保温系统应用技术规程

1 范围　 2 规范性引用文件　 3 术语和定义　 4 系统及组成材料　 4.1 性能要求　 4.2 包装与贮运　 5 设计　 5.1 一般要求　 5.2 构造设计　 5.3 热工设计　 6 施工　 6.1 一般要求　 6.2 施工工艺　 6.3 施工要点　 6.4 成品保护　 7 质量验收　 7.1 一般要求　 7.2 主控项目　 7.3 一般项目　 附 录 A（资料性）气凝胶保温膏料保温工程检验批质量验收记录　 附 录 B（规范性）气凝胶保温膏料保温系统材料检验规则　

Technical specification for application of aerogel thermal insulation paste thermal insulation system

T/SCDA 050-2023 DE烧结淤泥多孔砖复合保温墙体系统建筑构造

  1.本图集适用于民用建筑非承重框架填充墙。工业建筑在技术条件相同时也可适用。   2.本图集适用于抗震设防烈度7度地区的乙类和丙类建筑物。   3.本图集DE烧结淤泥多孔砖也可用于有保温要求的内隔墙。   4.DE砖复合保温墙体禁止采用外包墙形式。

DE sintered silt porous brick composite insulation wall system building structure

T/CASMES 159-2023 轻钢龙骨式复合墙体应用技术规程

本文件规定了轻钢龙骨式复合墙体的基本规定、材料、设计、施工、验收、墙体维护及拆除。

echnical specification for application of light-gauge steel framing wall panel

DB11/T 2128-2023 预制混凝土夹心保温外墙板应用技术规程

Technical regulations for the application of precast concrete sandwich insulation exterior wall panels

ASTM C1670/C1670M-23 粘合人造石砌面板单元的标准规范

1.1 This specification covers the minimum product requirements for adhered manufactured stone masonry veneer units applied as an adhered veneer to exterior and interior walls and structures suitable to receive units. 1.2 The property requirements of this specification apply at the time of delivery. This standard does not address the physical evaluation of installed units removed from service. 1.3 The units described by this specification are manufactured from a mixture of cement, normal or lightweight aggregates (or a combination of both), water, admixtures, other cementitious materials and other components which are wetcast into shapes simulating the appearance of natural stone and other textures. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—When particular features are desired such as surface textures or color these features should be specified separately. Suppliers should be consulted as to the availability of units having the desired features. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. A1.1 Scope A1.1.1 This annex provides information on determining the average unit thickness on adhered manufactured stone masonry veneer units. NOTE A1.1—Other methods than the one presented here for determining average thickness may exist. These other methods should be verified by comparing results to the method provided here. A1.2 Sample Size A1.2.1 From each manufacturing location, obtain a minimum of three (3) samples of units that are representative of the materials, concrete mix design, manufacturing process and curing method. A1.3 Volume Measurement A1.3.1 The net volume of each unit shall be determined by dividing the saturated weight (Ws) by the saturated density determined in accordance with 8.3. A1.4 Area Measurement A1.4.1 Determine the area of the unit using A1.4.2, A1.4.3, or A1.4.4. A1.4.2 Rectangular Units—For rectangular units, measure the minimum and maximum length and width of each unit to the nearest 0.1 in. [2.5 mm]. Average the measured lengths and widths of each unit and calculate the average area of each unit by multiplying the average length and average width A1.4.3 Circular or Oval Units—For circular or oval units, measure the length (defined as the largest diameter of each unit) and the width (defined as the smallest diameter of each unit) to the nearest 0.1 in. [2.5 mm]. Calculate the average area of each unit as follows: Area, in.2 @mm2 # 5 Π ×Slength 2 D×Swidth 2 D A1.4.4 Non–Rectangular Units—For non-rectangular units the area of a unit shall be determined using A1.4.4.1 or A1.4.4.2. C1670/C1670M − 23 5 A1.4.4.1 Trace the outline of each unit onto graph paper. Count the number of squares inside the outline. Estimate the number of partial squares that are contained inside the outline. Add the total number of squares and determine the area of each unit by multiplying the number of squares counted by the area of each square on the graph paper. A1.4.4.2 Cut a large, rectangular piece of graph paper to serve as control paper. Measure and record its area and mass. Divide the mass by area to compute the mass per unit area. Trace the outline of each unit onto graph paper. Cut out traced area and take weight of the paper cut out. Divide by weight by the mass per unit area of the control paper to calculate unit area. A1.5 Average Thickness Calculation A1.5.1 Determine the average thickness of each unit by dividing the unit volume determined in accordance with A1.3 by the unit area determined in accordance with A1.4. The average of the three ACMV unit thicknesses shall be reported as the average unit thickness for the lot. SUMMARY OF CHANGES Committee C15 has identified the location of selected changes to this standard since the last issue (C1670/C1670M – 21b) that may impact the use of this standard. (June 15, 2023) (1) Modified 5.3 and 5.5 to require three specimens for compressive strength testing. (2) Modified 6.3 and 6.4.2 to require three specimens for freeze-thaw durability testing. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website (www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/ C1670/C1670M − 23 6 

Standard Specification for Adhered Manufactured Stone Masonry Veneer Units

ASTM C946-23 干堆表面粘合墙施工的标准实施规程

1.1 This practice covers material, workmanship, and construction procedures for applying surface bonded mortar to both sides of dry stacked concrete masonry units. It does not include grout, reinforcing, anchorage, or control joints since their use is essentially the same as conventional concrete masonry construction, unless specifically mentioned in this practice. NOTE 1—Design and construction procedures for conventional concrete masonry construction are found in Building Code Requirements for Masonry Structures (TMS 402-16) and Specification for Masonry Structures (TMS 602-16). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls

T/SDBMIA 002-2023 DS钢丝网架组合板现浇混凝土墙体自保温系统建筑构造

1.适用范围； 2.设计依据； 3.编制内容； 4.系统构成及构造示意； 5.系统及材料性能要求； 6.设计要求； 7.构造节点详图等。 无强制性条文。

DS steel wire grid composite plate cast-in-place concrete wall self-insulation system building structure

T/SDBMIA 001-2023 DS内置钢丝网片组合板现浇混凝土墙体自保温系统应用技术规程

1.总则； 2.术语； 3.基本规定； 4.性能要求； 5.设计； 6.施工； 7.验收。

DS built-in steel wire mesh composite plate cast-in-place concrete wall self-insulation system application technical specification

T/CSTM 00442-2023 既有建筑幕墙面板坠落风险排查法 振动测试法

本文件规定了采用振动测试法排查既有建筑幕墙面板坠落风险的原理、检测设备、检测步骤、结果判定和检测报告。 本文件适用于既有建筑幕墙面板因支承不牢固（如隐框玻璃幕墙硅酮结构胶的粘结失效，石材及金属幕墙挂件、栓件的脱挂、漏挂、螺栓松动等）造成的坠落风险部位的定位，既有建筑幕墙安全检测中幕墙面板坠落风险排查可参照使用。

Investigation method for falling risk of the existing building curtain wall panels-Vibration test method

T/CECS 1281-2023 琉璃复合板幕墙工程技术规程

本规程共分9章和3个附录，主要内容包括：总则、术语和符号、材料、建筑设计、结构设计、加工制作、安装施工、工程验收、保养和维修等。

Technical specification for glazed composite panel curtain wall engineering

ASTM C1381/C1381M-23 模制玻璃纤维增强石膏部件的标准规范

1.1 This specification covers molded glass fiber reinforced gypsum (GRG) parts, which are nonload-bearing, thin-shell, ornamental shapes for architectural embellishment of interior building construction. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The information presented refers to the molded surface of the part. 1.4 The text of this standard references footnotes, which provide explanatory material. These footnotes shall not be considered as requirements of the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts

GSO ASTM C1032:2023 编织线石膏底座标准规范

This specification covers woven wire plaster base, flat or self-furring, with or without stiffener wires, and with or without backing, designed for use as a base to receive gypsum or Portland cement based plaster. Backing shall allow lapping of wire-to-wire and backing-to-backing of one mesh at ends and edges and shall have a minimum tensile breaking strength. The wire shall be zinc-coated (galvanized). The weight, size, and diameter of the wire are specified.

Standard Specification for Woven Wire Plaster Base

T/CECS 1266-2023 建筑幕墙设计标准

本标准共分9章和1个附录，主要内容包括：总则、术语、基本规定、性能要求、建筑设计、结构设计、构造设计、建筑幕墙设计阶段及要求、建筑幕墙信息化模型设计（BIM）等。

Building Curtain Wall Design Standards

ASTM E331-00(2023) 用均匀静态气压差测定外窗、天窗、门和幕墙的水渗透性的标准试验方法

1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a uniform static air pressure at the outdoor face higher than the pressure at the indoor face. 1.2 This test method is applicable to any curtain-wall area or to windows, skylights, or doors alone. 1.3 This test method addresses water penetration through a manufactured assembly. Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass. This test method does not address these issues. 1.4 The proper use of this test method requires a knowledge of the principles of pressure measurement. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 7.1. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference

ASTM E2511-17(2023) EIFS包层屏障和排水墙组件详细说明的标准指南

1.1 This guide describes the types of project-specific construction conditions that need to be communicated by means of drawings (“details”) for the purpose of constructing Exterior Insulation and Finish System (EIFS)-clad barrier and drainage wall assemblies. EIFS manufacturers provide basic details for the installation of their materials and interface with adjacent materials. These details are generic and, in many cases, do not apply to specific project conditions. 1.2 This guide addresses only the EIFS itself and the interface between the EIFS and the materials immediately adjacent to the EIFS; it does not address all parts of the wall assembly. 1.3 Not all possible construction detail conditions are addressed by this guide. Identify and provide details for all construction conditions that exist on a specific building. 1.4 This guide is intended to supplement but not supersede information from the EIFS manufacturer about how their specific product should be detailed, nor to supersede technical product acceptance reports or the code requirements of regulatory authorities. 1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies

BS ISO 24084:2022 幕墙 层间位移阻力 测试方法

1   Scope This document specifies the test method to evaluate the inter-storey displacement resistance of curtain walling to three-directional seismic or wind actions when curtain walling is subjected to repeated movement. The test method allows to determine, depending on the axes of the displacement imposed: — horizontal inter-storey displacement in-plane resistance ; — horizontal inter-storey out-plane displacement resistance ; — vertical inter-storey in-plane displacement resistance ; — combined inter-storey displacement resistance . The test method can be used to evaluate the inter-storey displacement either when it is a design requirement or to assess the relative displacement accommodated by the curtain walling assembly. This test can be addressed manually or automatically depending on the size and/or the shape of the specimen.

Curtain walling. Inter-storey displacement resistance. Test method

DB11/ 1003-2022 装配式剪力墙结构设计规程

Code for design of prefabricated shear wall structures