91.060.10 墙、隔墙、面墙 标准查询与下载

T/ZS 0367-2022 装配式玻纤增强无机材料复合保温墙板应用技术规程

前??言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 材料　 4.1 一般要求　 4.2 金属材料　 4.3 面板　 4.4 保温材料　 4.5 外围护墙板　 5 设计　 5.1 一般要求　 5.2 外围护墙体　 5.3 隔墙　 6 加工制作与运输　 6.1 一般要求　 6.2 加工制作　 6.3 质量检验　 6.4 运输与堆放　 7 安装施工　 7.1 一般要求　 7.2 施工准备　 7.3 预埋件　 7.4 外围护墙体　 7.5 隔墙　 7.6 施工安全　 8 工程验收　 9 保养和维护　

Technical specification for application of assembled glass fiber reinforced inorganic materials composite insulation wallboard

ISO 24084:2022 幕墙.层间位移阻力.试验方法

This document specifies the test method to evaluate the inter-s torey displacement resistance of curtain walling to three-directional seismic or wind actions when curtain walling is subj ected to repeated movement. The test method allows to determine, depending on the axes of the displacement imposed: — horizontal inter-storey displacement in-plane resis tance; — horizontal inter-storey out-plane displacement resis tance; — vertical inter-s torey in-plane displacement resistance; — combined inter-s torey displacement resis tance. The test method can be used to evaluate the inter-s torey displacement either when it is a design requirement or to assess the relative displacement accommodated by the curtain walling assembly. This test can be addressed manually or automatically depending on the size and/or the shape of the specimen.

Curtain walling — Inter-storey displacement resistance — Test method

ASTM D5319-22 玻璃纤维增强聚酯墙板和天花板标准规范

1.1 This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of testing glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structural applications. 1.2 Supplementary information on chemical resistance, impact resistance, and installation practice are provided in Appendix X1. 1.3 The classification of these composite panels into classes based on relative response to a laboratory test shall not be considered a fire-hazard classification. 1.4 This specification contains laboratory flammability tests (Test Methods E84 and D1929). In this standard flammability tests are used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but do not by themselves incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 The intent of this specification is to define the class, grade, and general laminate properties of the composite wall and ceiling liner panels in order to ensure a quality product which will perform in the intended application. This specification is not intended to restrict or limit technological changes affecting performance when changes are agreed upon between the purchaser and manufacturer. 1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in Tables and Figures) shall not be considered as requirements of this specification. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels

BS EN 13830:2015+A1:2020 幕墙 产品标准

Curtain walling. Product standard

T/SDBMIA 008-2022 TTL高精度榫接空心模块装配式墙体建筑构造

本图集的主要技术内容包括： 1.适用范围； 2.设计依据； 3.编制内容； 4.系统构成及构造示意； 5.系统及材料性能要求； 6.设计要求； 7.构造节点详图等。 无强制性条文。

TTL high-precision mortise joint hollow module assembly wall building structure

T/SDBMIA 007-2022 TTL高精度榫接空心模块装配式墙体应用技术规程

本规程的主要技术内容包括： 1.总则； 2.术语； 3.基本规定； 4.性能要求； 5.设计； 6.施工； 7.验收。 无强制性条文。

TTL high-precision mortise joint hollow module assembly wall application technical regulations

JC/T 2672-2022 建筑用植物纤维水泥墙板

本文件规定了建筑用植物纤维水泥墙板的术语和定义、分类与标记、要求、试验方法、检验规则、标志、运输和贮存。 本文件适用于工业与民用建筑墙体用植物纤维水泥板。

Plant fiber cement wall panels for construction

KS F 1518-2022 建筑板标准公称尺寸

Standard nominal dimension of boards of buildings

KS F 1517-2022 建筑物活动隔断构件标准公称尺寸

Standard nominal dimension of movable partition components for buildings

GSO ASTM C1795:2022 石膏板和面板高温特性的标准测试方法

1.1 These test methods describe three bench top test methods for measuring the thermophysical responses of gypsum boards and panels when exposed to high temperatures. The test methods are: 1.1.1 High-temperature Core Cohesion—This test method evaluates the ability of the test specimen to withstand a specified mechanical strain while exposed to elevated temperature. 1.1.2 High-temperature Shrinkage—This test method evaluates dimensional changes in the test specimen when exposed to elevated temperatures. 1.1.3 High-temperature Thermal Insulation—This test method evaluates the rate of heat transfer through the thickness of the test specimen by measuring the length of time required to heat the center of the test specimen over a specified temperature rise when exposed to prescribed furnace conditions.

Standard Test Methods for High-Temperature Characterization of Gypsum Boards and Panels

ASTM E2556/E2556M-10(2022) 用于机械附件的透气性柔性板防水屏障的标准规范

1.1 This specification is limited to vapor permeable flexible sheet materials which are intended to be mechanically attached and are generally installed behind the cladding system in exterior walls. 1.2 This specification is limited to the evaluation of materials and does not address installed performance. Although the fastening practices (type of fastener, fastening schedule, etc.) may affect the installed function of these materials, they are not included in this specification. 1.3 This specification does not address integration of the water-resistive barrier with other wall elements. The topic is addressed in more detail in Practice E2112 and Guide E2266. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment

ASTM E72-22 建筑结构用面板强度试验的标准试验方法

1.1 These test methods cover the following procedures for determining the structural properties of segments of wall, floor, and roof constructions: Section Test Specimens 3 Loading 4 Deformation Measurements 5 Reports 6 Precision and Accuracy 7 TESTING WALLS Significance and Use 8 Compressive Load 9 Tensile Load 10 Transverse Load—Specimen Horizontal 11 Transverse Load—Specimen Vertical 12 Concentrated Load 13 Impact Load—See Test Methods E695 and E661 Racking Load—Evaluation of Sheathing Materials on a Standard Wood Frame 14 Racking Load—Evaluation of Sheathing Materials (Wet) on a Standard Wood Frame 15 TESTING FLOORS Significance and Use 16 Transverse Load 17 Concentrated Load 18 Impact Load—See Test Methods E695 and E661 TESTING ROOFS Section Significance and Use 19 Transverse Load 20 Concentrated Load 21 APPENDIX Technical Interpretation Appendix X1 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods of Conducting Strength Tests of Panels for Building Construction

JC/T 60012-2022 型钢网架整体喷筑速凝墙体技术规程

本标准适用于七层及以下一般工业与民用建筑中以型钢网架整体喷筑速凝墙体作为非承重墙体的设计、施工及质量验收。

Technical specifications for quick-setting wall construction by integral spraying of section steel grid

DB11/T 2003-2022 蒸压加气混凝土墙板系统应用技术规程

Technical specification for application of autoclaved aerated concrete wall panel system

T/FSNZ 13-2022 非承重玻璃隔墙通用技术条件

非承重玻璃隔墙的术语和定义、分类、规格和标记、一般要求、要求、试验方法

General technical requirements for non-load-bearing glass partition walls

T/SDBMIA 006-2022 UTS钢丝拉结网片组合板现浇混凝土墙体自保温系统建筑构造

本图集的主要技术内容包括： 1.适用范围； 2.设计依据； 3.编制内容； 4.系统构成及构造示意； 5.系统及材料性能要求； 6.设计要求； 7.构造节点详图等。 无强制性条文。

UTS steel wire tie mesh composite plate cast-in-place concrete wall self-insulation system building structure

T/SDBMIA 005-2022 UTS钢丝拉结网片组合板现浇混凝土墙体自保温系统应用技术规程

本规程的主要技术内容包括： 1.总则； 2.术语； 3.基本规定； 4.性能要求； 5.设计； 6.施工； 7.验收。 无强制性条文。

Application technical specification for cast-in-place concrete wall self-insulation system of UTS steel wire tie mesh composite slab

T/SDBMIA 001-2022 ISS双丝扣合钢丝网片组合板现浇混凝土墙体自保温系统应用技术规程

规程适用于山东省内抗震设防烈度为8度及8度以下地区工业与民用建筑现浇混凝土墙体保温工程的设计、施工及验收。本规程的主要技术内容包括：1.总则；2.术语；3.基本规定；4.性能要求；5.设计；6.施工；7.验收。无强制性条文。

ISS double wire fastening steel wire mesh composite plate cast-in-place concrete wall self-insulation system application technical specification

T/SDBMIA 002-2022 ISS双丝扣合钢丝网片组合板现浇混凝土墙体自保温系统建筑构造

本图集适用于山东省内抗震设防烈度为8度及8度以下地区工业与民用建筑现浇混凝土墙体保温工程的设计、施工及验收。本图集的主要技术内容包括：1.适用范围；2.设计依据；3.编制内容；4.系统构成及构造示意；5.系统及材料性能要求；6.设计要求；7.构造节点详图等。无强制性条文。

ISS double-wire fastening steel wire mesh composite plate cast-in-place concrete wall self-insulation system building structure

ASTM C1776/C1776M-17(2022) 湿铸预制模块式挡土墙单元的标准规范

1.1 This specification covers wet-cast precast modular retaining wall units cast from first-purpose concrete with or without the inclusion of steel reinforcement. The precast units covered by this specification are machine-placed units intended for use in the construction of dry stacked modular retaining wall systems. 1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text of the specification, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wet-Cast Precast Modular Retaining Wall Units