91.060.10 墙、隔墙、面墙 标准查询与下载

T/GDLF 9-2022 建筑外墙防水装饰工程验收规程

本文件规定了建筑外墙防水装饰工程验收的基本规定、施工过程验收和竣工验收的内容。 本文件适用于对建筑外墙防水装饰工程进行验收。

Acceptance rules for building exterior wall waterproof decoration project

ASTM C1372-22 干铸分段挡土墙构件标准规范

1.1 This specification covers dry-cast segmental retaining wall units of concrete, machine–made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. The units are intended for use in the construction of mortarless segmental retaining walls. NOTE 1—When particular features are desired, such as density classification, higher compressive strength, surface texture, finish, color, or other special features, such properties should be specified separately by the purchaser. Suppliers should be consulted as to availability of units having the desired features. 1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Dry-Cast Segmental Retaining Wall Units

T/CIEEMA 008-2022 烧结保温轻质复合墙板应用技术规程

1 总则 2 术语 3 基本规定 4 材料 5 设计 6 施工 7 验收

Technical specification for application of sintered thermal insulation lightweight composite wallboard

T/ZZB 2912-2022 室内装饰用石塑板材

本文件规定了室内装饰用石塑板材的术语和定义、分类和标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于石粉和PVC树脂组成的室内装饰用石塑板材(以下简称石塑板材)。

Stone-plastic sheet for interior decoration

T/ZS 0391-2022 灌浆套筒剪力墙应用技术规范

前  言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本要求　 5 材料　 5.1 一般要求　 5.2 混凝土、钢筋和钢材　 5.3 套筒及连接材料　 5.4 其他材料　 5.5 材料管理　 6 设计要求　 6.1 一般要求　 6.2 建筑平面设计　 6.3 立面、外墙设计　 6.4 预制构件设计　 7 构建制作与运输　 7.1 一般要求　 7.2 工艺试验和检验　 7.3 灌浆套筒剪力墙制作与验收　 7.4 预制构件运输　 8 预制构件安装　 8.1 一般要求　 8.2 安装与连接　 9 验收　 附录A（规范性）坐浆料性能指标 　

Technical specification for grouting sleeve shear wall application

T/GCES 0002-2022 轻钢龙骨喷筑复合墙板应用技术规程

本规程规定了轻钢龙骨喷筑复合墙板的术语、材料、设计、施工、质量验收。

Technical regulations for the application of light steel keel spray-cast composite wall panels

ASTM C1197-22 用平板千斤顶法现场测量砌体变形性能的标准试验方法

1.1 This test method describes an in situ method for determining the deformation properties of existing unreinforced solid-unit masonry. (See Note 1.) This test method concerns the measurement of in-situ masonry deformability properties in existing masonry by use of thin, bladder-like flatjack devices that are installed in cut mortar joints in the masonry wall. This test method provides a relatively nondestructive means of determining masonry properties. NOTE 1—Solid-unit masonry is that built with stone, concrete, or clay units whose net area is equal to or greater than 75 % of the gross area. 1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method

ASTM E518/E518M-22 砌体抗弯粘结强度的标准试验方法

1.1 These test methods cover determination of the flexural bond strength of unreinforced masonry assemblages. Two procedures are provided: 1.1.1 Test Method A—Simply supported beam with thirdpoint loading. 1.1.2 Test Method B—Simply supported beam with uniform loading. NOTE 1—Third-point loading (Test Method A) produces a moment distribution that is significantly different from uniformly distributed loading (Test Method B).Third-point loading (Test Method A) subjects more mortar joints to the maximum moment and thus, is likely to produce more conservative capacities than uniform loading (Test Method B). 1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Flexural Bond Strength of Masonry

ASTM C1072-22 砌体抗弯粘结强度测量的标准试验方法

1.1 These test methods evaluate the flexural bond strength, normal to the bed joints, of masonry built of manufactured masonry units. Sampling and testing procedures are referenced, and terms are defined. Three different specimen fabrication methods are specified, each for a different purpose: 1.1.1 The first method is the “Test Method for LaboratoryPrepared Specimens.” Its purpose is to compare the bond strengths (under the given conditions) of masonry mortars. It could be used, for example, to check the quality of mortar products after production, or to indicate the bond strength (under the given conditions) of a mortar product without requiring the product to be tested in combination with many different units. It is not intended to represent field conditions. It uses standard concrete masonry units. Mortars are batched by weight equivalents of volume proportions and are mixed to a prescribed flow. Prisms are constructed using a jig and are bag-cured. 1.1.2 The second method is the “Test Method for FieldPrepared Specimens.” Its purpose is to evaluate the bond strength (under the given conditions) of a particular unit-mortar combination, either for preconstruction evaluation of materials or for quality control purposes during construction. Mortars are batched conventionally, and the flow is not prescribed. Prisms are constructed conventionally (no jig) and are bag-cured. 1.1.3 The third method is the “Test Method for Prisms Removed from Existing Masonry.” Its purpose is to evaluate the bond strength of unit-mortar combinations of prisms cut from existing walls. 1.1.4 The three methods are not consistent, nor are they intended to be. They are intended to be used for three different purposes. To make this clear, the three methods are presented separately. 1.1.5 Appendix X1 suggests two possible criteria for assessing the bond strength values obtained using these test methods. These possible evaluation criteria are given for illustration only and are not mandatory. 1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Measurement of Masonry Flexural Bond Strength

ASTM E519/E519M-22 砌体组件中对角线张力（剪切）的标准试验方法

1.1 This test method covers determination of the diagonal tensile or shear strength of masonry assemblages by loading them in compression along one diagonal (see Fig. 1), thus causing a diagonal tension failure with the specimen splitting apart parallel to the direction of load. 1.2 Annex A1 provides requirements regarding the determination of the diagonal-tension strength of masonry under combined diagonal-tension and compressive loading. 1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages

T/ZS 0377-2022 内外墙涂饰工程施工及验收规范

1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本要求　 5 材料　 6 基层工艺　 7 施工 8 验收　 附录 A（规范性）复试项目　

Specication for construction and acceptance of building finishings for interior and exterior wall

T/ZS 0367-2022 装配式玻纤增强无机材料复合保温墙板应用技术规程

前??言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 材料　 4.1 一般要求　 4.2 金属材料　 4.3 面板　 4.4 保温材料　 4.5 外围护墙板　 5 设计　 5.1 一般要求　 5.2 外围护墙体　 5.3 隔墙　 6 加工制作与运输　 6.1 一般要求　 6.2 加工制作　 6.3 质量检验　 6.4 运输与堆放　 7 安装施工　 7.1 一般要求　 7.2 施工准备　 7.3 预埋件　 7.4 外围护墙体　 7.5 隔墙　 7.6 施工安全　 8 工程验收　 9 保养和维护　

Technical specification for application of assembled glass fiber reinforced inorganic materials composite insulation wallboard

ISO 24084:2022 幕墙.层间位移阻力.试验方法

This document specifies the test method to evaluate the inter-s torey displacement resistance of curtain walling to three-directional seismic or wind actions when curtain walling is subj ected to repeated movement. The test method allows to determine, depending on the axes of the displacement imposed: — horizontal inter-storey displacement in-plane resis tance; — horizontal inter-storey out-plane displacement resis tance; — vertical inter-s torey in-plane displacement resistance; — combined inter-s torey displacement resis tance. The test method can be used to evaluate the inter-s torey displacement either when it is a design requirement or to assess the relative displacement accommodated by the curtain walling assembly. This test can be addressed manually or automatically depending on the size and/or the shape of the specimen.

Curtain walling — Inter-storey displacement resistance — Test method

ASTM D5319-22 玻璃纤维增强聚酯墙板和天花板标准规范

1.1 This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of testing glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structural applications. 1.2 Supplementary information on chemical resistance, impact resistance, and installation practice are provided in Appendix X1. 1.3 The classification of these composite panels into classes based on relative response to a laboratory test shall not be considered a fire-hazard classification. 1.4 This specification contains laboratory flammability tests (Test Methods E84 and D1929). In this standard flammability tests are used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but do not by themselves incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 The intent of this specification is to define the class, grade, and general laminate properties of the composite wall and ceiling liner panels in order to ensure a quality product which will perform in the intended application. This specification is not intended to restrict or limit technological changes affecting performance when changes are agreed upon between the purchaser and manufacturer. 1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in Tables and Figures) shall not be considered as requirements of this specification. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels

BS EN 13830:2015+A1:2020 幕墙 产品标准

Curtain walling. Product standard

T/SDBMIA 008-2022 TTL高精度榫接空心模块装配式墙体建筑构造

本图集的主要技术内容包括： 1.适用范围； 2.设计依据； 3.编制内容； 4.系统构成及构造示意； 5.系统及材料性能要求； 6.设计要求； 7.构造节点详图等。 无强制性条文。

TTL high-precision mortise joint hollow module assembly wall building structure

T/SDBMIA 007-2022 TTL高精度榫接空心模块装配式墙体应用技术规程

本规程的主要技术内容包括： 1.总则； 2.术语； 3.基本规定； 4.性能要求； 5.设计； 6.施工； 7.验收。 无强制性条文。

TTL high-precision mortise joint hollow module assembly wall application technical regulations

JC/T 2672-2022 建筑用植物纤维水泥墙板

本文件规定了建筑用植物纤维水泥墙板的术语和定义、分类与标记、要求、试验方法、检验规则、标志、运输和贮存。 本文件适用于工业与民用建筑墙体用植物纤维水泥板。

Plant fiber cement wall panels for construction

KS F 1517-2022 建筑物活动隔断构件标准公称尺寸

Standard nominal dimension of movable partition components for buildings

KS F 1518-2022 建筑板标准公称尺寸

Standard nominal dimension of boards of buildings