91.060.10 墙、隔墙、面墙 标准查询与下载

T/CECS 926-2021 桁架加劲多腔体钢板组合剪力墙技术规程

主要技术内容包括：总则、术语和符号、基本规定、集成设计、结构类型、结构计算分析、桁架加劲多腔体钢板组合剪力墙设计、连接与节点设计、防护设计、施工、验收和使用维护等。

Technical specifications for truss-stiffened multi-cavity steel plate composite shear walls

NF P75-501-1-2:2021 建筑工程 带通风覆层的外部隔热系统 第 1-2 部分：材料选择的一般标准

Building works - Systems of external heat insulation with ventilated cladding - Part 1-2 : General criteria for selection of materials

ASTM E330/E330M-14(2021) 用均匀静态气压差法测定外窗、门、天窗和幕墙结构性能的标准试验方法

1.1 This test method describes the determination of the structural performance of exterior windows, doors, skylights, and curtain walls under uniform static air pressure differences, using a test chamber. This test method is applicable to curtain wall assemblies including, but not limited to, metal, glass, masonry, and stone components.2 1.2 This test method is intended only for evaluating the structural performance associated with the specified test specimen and not the structural performance of adjacent construction. 1.3 The proper use of this test method requires a knowledge of the principles of pressure and deflection measurement. 1.4 This test method describes the apparatus and the procedure to be used for applying uniformly distributed test loads to a specimen. 1.4.1 Procedure A (see 11.2) shall be used when a loaddeflection curve is not required. 1.4.2 Procedure B (see 11.3) shall be used when a loaddeflection curve is required. 1.5 The text of this standard references notes and footnotes which provide explanatory materials. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference

T/CECS 929-2021 纸蜂窝复合墙板应用技术规程

主要内容包括：总则、术语、材料、设计选用、安装施工、质量验收、维护和保养等。

Application technical specification for paper honeycomb composite wallboard

PN-EN 16758-2021-10 E 幕墙—剪切连接强度的测定—试验方法和要求

Curtain walling -- Determination of the strength of sheared connections -- Test method and requirements

ASTM E3036-15(2021) 现场标记立面条件的标准指南

1.1 This guide consists of symbols and notations pertaining to documenting deficient conditions observed during facade inspections. 1.2 The purpose of this guide is to provide a quick shorthand, notation system that will serve as a uniform system for facade inspectors to record their observations on existing elevation drawings or photographs, or both, of existing building facades. 1.3 This guide is not intended to be used to record or document a diagnosis for the particular symptom. 1.4 Notations are listed in alphabetical order. Compound terms appear as per the first word as spoken. 1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Notating Facade Conditions in the Field

T/CECS 10154-2021 陶粒发泡混凝土一体化墙板

本文件规定了陶粒发泡混凝土一体化墙板的术语和定义，分类、规格和标记，材料，要求，试验方法，检验规则，标志、随行文件、包装、运输与贮存。

Ceramsite foamed concrete integrated wall panel

T/CECS 915-2021 装配式空心板叠合剪力墙结构技术规程

主要技术内容包括：总则、术语和符号、基本规定、材料、建筑设计、结构设计、构件生产与运输、施工安装和质量验收等。

Technical specification for prefabricated hollow slab laminated shear wall structure

prEN 14024-2021 带隔热层的金属型材 机械性能 评估的要求、证明和试验

Metal profiles with thermal barrier - Mechanical performance - Requirements, proof and tests for assessment

T/CECS 908-2021 混凝土异形柱-钢丝网架保温墙体复合结构应用技术规程

主要技术内容是：总则、术语和符号、材料、设计与构造、施工和验收。 

Technical specification for application of composite structure of concrete special-shaped column-steel wire grid insulation wall

LST EN 16758-2021 幕墙剪力连接强度的测定试验方法和要求

Curtain walling - Determination of the strength of shear connections - Test method and requirements

T/ZZB 2174-2021 建筑室内用预制金属面板复合墙体

本文件规定了建筑室内用预制金属面板复合墙体的术语和定义、分类、规格及标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量与服务承诺等的要求。 本文件适用于建筑室内的非承重可拆装式隔断墙。

Prefabricated metal panel composite wall for building interior

DB42/T 1709-2021 既有建筑幕墙可靠性鉴定技术规程

Technical specification for reliability appraisal of existing building curtain wall

DB42/T 1711-2021 轻钢龙骨-混合相磷石膏喷筑墙体技术规程

Technical specification for light steel keel-mixed-phase phosphogypsum sprayed walls

GSO ASTM C645:2021 非结构钢框架构件标准规范

This specification covers nonstructural steel framing members in interior construction assemblies. Members shall be manufactured from steel and shall have a protective coating. Studs and rigid furring channels shall have a configuration and steel thickness such that the system in which they are used will carry the design transverse loads without exceeding either the allowable stress of the steel or the allowable design deflection. Members shall be manufactured in such a fashion as to minimize burrs and sharp edges. Penetration test shall be done for performance requirements, where members shall be capable of pulling the head of the screw below the surface of the gypsum board without spin out. Apparatus and materials shall satisfy the testing requirements of the specification.

Standard Specification for Nonstructural Steel Framing Members

GSO ASTM E2511:2021 EIFS 包层屏障和排水墙组件详图标准指南

1.1 This guide describes the types of project-specific construction conditions that need to be communicated by means of drawings (“details”) for the purpose of constructing Exterior Insulation and Finish System (EIFS)-clad barrier and drainage wall assemblies. EIFS manufacturers provide basic details for the installation of their materials and interface with adjacent materials. These details are generic and, in many cases, do not apply to specific project conditions. 1.2 This guide addresses only the EIFS itself and the interface between the EIFS and the materials immediately adjacent to the EIFS; it does not address all parts of the wall assembly. 1.3 Not all possible construction detail conditions are addressed by this guide. Identify and provide details for all construction conditions that exist on a specific building. 1.4 This guide is intended to supplement but not supersede information from the EIFS manufacturer about how their specific product should be detailed, nor to supersede technical product acceptance reports or the code requirements of regulatory authorities.

Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies

GSO ASTM C1766:2021 工厂层压石膏板产品的标准规范

This specification establishes the requirements for factory-laminated gypsum panel products designed for use either on walls, ceilings, or partitions as part of a sound control system, or as a gypsum stud or gypsum coreboard. It covers materials and manufacture, physical properties, dimensions and tolerances, finish and appearance, sampling, inspection, rejection, certification, packaging, marking, shipping, handling, and storage.

Standard Specification for Factory-Laminated Gypsum Panel Products

GSO ISO 16283-3:2021 声学 建筑物和建筑构件隔音的现场测量 第3部分：外墙隔音

ISO 16283-3:2016 specifies procedures to determine the airborne sound insulation of façade elements (element methods) and whole façades (global methods) using sound pressure measurements. These procedures are intended for room volumes in the range from 10 m3 to 250 m3 in the frequency range from 50 Hz to 5 000 Hz. The test results can be used to quantify, assess, and compare the airborne sound insulation in unfurnished or furnished rooms where the sound field can or cannot approximate to a diffuse field. The measured airborne sound insulation is frequency-dependent and can be converted into a single number quantity to characterize the acoustic performance using the rating procedures in ISO 717-1.

Acoustics — Field measurement of sound insulation in buildings and of building elements — Part 3: Façade sound insulation

DS/ISO 22497:2021 门、窗和幕墙 – 幕墙 – 词汇

Doors, windows and curtain walling – Curtain walling – Vocabulary

UNI EN 16758-2021 幕墙剪力连接强度的测定试验方法和要求

Curtain walling - Determination of the strength of shear connections - Test method and requirements